Search Results

Due to the design of lightweight, high speed driveline system, the coupled bending and torsional vibration and rotordynamics must be considered to predict vibratory responses more realistically. In the current analysis, a lumped parameter model of the propeller shaft is developed with Timoshenko beam elements, which includes the effect of rotary inertia and shear deformation. The propeller shaft model is then coupled with a hypoid gear pair representation using the component mode synthesis approach. In the proposed formulation, the gyroscopic effect of both the gear and propeller shaft is considered. The simulation results show that the interaction between gear gyroscopic effect and propeller shaft bending flexibility has considerable influence on the gear dynamic mesh responses around bending resonances, whereas the torsional modes still dominate in the overall frequency spectrum.

Squeak and rattle (S&R) problems in body structure and trim parts have become serious issues for automakers because of their influence on the initial quality perception of consumers. In this study, various CAE and experimental methods developed by Hyundai Motors for squeak and rattle analysis of door systems are reported. Friction-induced vibration and noise generation mechanisms of a door system are studied by an intelligent combination of experimental and numerical methods. It is shown that the effect of degradation of plastics used in door trims can be estimated by a numerical model using the properties obtained experimentally. Effects of changes in material properties such as Young's modulus and loss factor due to the material degradation as well as statistical variations are predicted for several door system configurations. As a new concept, the rattle and squeak index is proposed, which can be used to guide the design.

Cycloid drives are widely used in the in-wheel motor for electric vehicles due to the advantages of large ratio, compact size and light weight. To improve the transmission efficiency and the load capability and reduce the manufacturing cost, a novel cycloid drive with non-pin design for the application in the in-wheel motor is proposed. Firstly, the generation of the gear pair is presented based on the gearing of theory. Secondly, the meshing characteristics, such as the contact zones, curvature difference, contact ratio and sliding coefficients are derived for performance evaluation. Then, the loaded tooth contact analysis (LTCA) is performed by establishing a mathematical model based on the Hertz contact theory to calculate the contact stress and deformation.

A combined lumped parameter, finite element (FE) and boundary element (BE) model is developed to predict the whine noise from rear axle. The hypoid geared rotor system, including the gear pair, shafts, bearings, engine and load, is represented by a lumped parameter model, in which the dynamic coupling between the engaging gear pair is represented by a gear mesh model condensed from the loaded tooth contact analysis results. The lumped parameter model gives the dynamic bearing forces, and the noise radiated by the gearbox housing vibration due to the dynamic bearing force excitations is calculated using a coupled FE-BE approach. Based on the predicted noise, a new procedure is proposed to tune basic rear axle design parameters for better sound quality purpose. To illustrate the salient features of the proposed method, the whine noise from an example rear axle is predicted and tuned.

Looking forward to an autonomous Unmanned Combat Aerial Vehicle (UCAV) for future applications, it becomes apparent that on-board intelligent controllers will be necessary for these advanced systems. LETHA (Learning Enhanced Tactical Handling Algorithm) was created to develop intelligent managers for these advanced unmanned craft through the novel means of a genetic cascading fuzzy system. In this approach, a genetic algorithm creates rule bases and optimizes membership functions for multiple fuzzy logic systems, whose inputs and outputs feed into one another alongside crisp data. A simulation space referred to as HADES (Hoplological Autonomous Defend and Engage Simulation) was created in which LETHA can train the UCAVs intelligent controllers.

Spiral bevel gear dynamics are significantly affected by the flexibilities of shafts and bearings. In this study, a new shaft-bearing model has been proposed for computing the effective support stiffness. The results are applied to the lumped parameter dynamic model of spiral bevel geared rotor system with 3-bearing straddle-mounted pinion configuration. Also, using the multi-degree of freedom lumped parameter dynamic model and quasi-static three-dimensional finite element tooth contact analysis program, the responses of two typical shaft-bearing configurations used in automotive applications, that are the 3-bearing straddle mounted pinion configuration and the 2-bearing overhung mounted pinion configuration, are compared. The comparative analysis along with a set of parametric studies highlights their different contributions to the spiral bevel gear mesh characteristics and dynamic response.

The noise and vibration response of hypoid or bevel geared rotor system, primarily excited by transmission error (TE), and mesh vector and stiffness variations, can be affected significantly by the coupling between the driveline rotor dynamics and gear vibratory response. This is because of the inherent design comprising of non-parallel rotational axes and time-varying as well as spatial-varying gear mesh characteristics. One of the important factors of the driveline system dynamics is the rotor gyroscopic effect that has not been studied extensively in traditional gear dynamics. To address this gap in the literature, this paper attempts to examine the influence of incorporating gyroscopic terms in the hypoid gear dynamic simulation. A multi-degrees-of-freedom, multi-body dynamic model is used as a generalized representation of a hypoid geared rotor system.

High speed, precision geared rotor systems are often plagued by excessive vibration and noise problems. The response that is primarily excited by gear transmission error is actually coupled to the large displacement rotational motion of the driveline system. Classical pure vibration model assumes that the system oscillates about its mean position without coupling to the large displacement motion. To improve on this approach and understanding of the influences of the dynamic coupling, a coupled multi-body dynamic and vibration simulation model is proposed. Even though the focus is on hypoid geared rotor system, the model is more general since hypoid and bevel gears have more complicated geometry and time and spatial-varying characteristics compared to parallel axis gears.

A proposed multi-coordinate spectral-based inverse substructuring approach is applied experimentally to examine the vibration transmissibility through chassis mounts. In this formulation, the vehicle system is partitioned into two substructures. One substructure comprises of the chassis and suspension, while the second one is the body structure and other attached components. The approach yields the free substructure dynamic characteristics that are extracted from the measured coupled system response spectra. The resultant free substructure transfer functions are verified by comparison of the re-synthesized results to the actual vehicle system measurements. A real life vehicle setup is utilized to demonstrate the salient features and capabilities of this approach, which includes the ability to compute the main structure-borne paths, dynamic interactions between the chassis and body, and interior noise and vibration response.

A manual task can be performed based on alternative movement techniques. Ergonomic human motion simulation requires consideration of alternative movement techniques, because they could bring different biomechanical, physiological, and psychophysical consequences. A method for identifying movement techniques from existing motion data was developed. The method is based on a JCV (Joint Contribution Vector) index and statistical clustering. A JCV quantifies a motion's underlying movement technique by computing contributions of individual body joint DOFs (degree-of-freedom) to the achievement of the task goal. Given a set of motions (motion capture data) achieving the same or similar task goals, alternative movement techniques can be identified by 1) representing the motions in terms of JCV and 2) performing a statistical clustering analysis. Performance of this movement technique identification method was evaluated based on a set of stoop and squat lifting motions.

The perturbed boundary condition (PBC) model updating procedure has been developed to correct the finite element model [1]. The use of additional structural configurations adds more experimental information about the system and so better updating results can be expected. While it works well for simulated examples, practical limitations and additional requirements arise when it is used to update engineering structures. In this paper, the merits and the practical limitations of the techmques will be discussed in depth through the updating of a simulated system where the “measured” data is generated by computer and a real test structure where the experimentally measured data is noisy and distorted due to leakage. Useful suggestions and recommendations are drawn to guide the model updating of practical engineering structures.

In this work, the goal of enhanced reliability through redundancy is explored. Two levels of fusion have been defined: the first is a fusion of sensors, redundant in both number and type, and the second is a statistical fusion of the resulting data at a software level. An intermediate preprocessing level is required to connect both fusions. The various types of sensors which are included are bulk micromachined flow, pressure and hydrogen sensors and a thin film poly-crystalline silicon temperature sensor. Individual sensors have been fabricated and packaged in arrays. Associated preprocessing has been designed to be able to handle all of the signals coming from each sensor and prepare them for statistical analysis. Data fusion algorithms have been written and tested.

Modeling of liner cavitation corrosion is of increasing significance since new engine design trends could aggravate the problem. Cavitation corrosion is of a complex nature and is affected by numerous coupled factors. A system approach to analyze and assess cavitation corrosion damage is deemed necessary. The approach accounts for the macroscopic and microscopic aspects of the phenomenon that include modeling of piston dynamics, liner transient vibration, pressure wave propagation, bubble dynamics and their effect on material damage. Though detection methods can provide crucial insight of factors that influence the cavitation problem, analysis methods are required at the initial design stage to provide overall engine design optimization and reduce prototype development cost and time. This analytical diagnostic approach provides a powerful tool to give valuable and relatively quick insight in solving engine liner cavitation corrosion problems.