Search Results

For intelligent vehicles, a robust perception system relies on training datasets with a large variety of scenes. The architecture of federated learning allows for efficient collaborative model iteration while ensuring privacy and security by leveraging data from multiple parties. However, the local data from different participants is often not independent and identically distributed, significantly affecting the training effectiveness of autonomous driving perception models in the context of federated learning. Unlike the well-studied issues of label distribution discrepancies in previous work, we focus on the challenges posed by scene heterogeneity in the context of federated learning for intelligent vehicles and the inadequacy of a single scene for training multi-task perception models. In this paper, we propose a federated learning-based perception model training system.

Fracture characterization of automotive metals under simple shear deformation is critical for the calibration of advanced fracture models employed in forming and crash simulations. In-plane shear fracture tests of high ductility materials have proved challenging since the sample edge fails first in uniaxial tension before the fracture limit in shear is reached at the center of the gage region. Although through-thickness machining is undesirable, it appears required to promote higher strains within the shear zone. The present study seeks to adapt existing in-plane shear geometries, which have otherwise been successful for many automotive materials, to have a local shear zone with a reduced thickness. It is demonstrated that a novel shear zone with a pocket resembling a “peanut” can promote shear fracture within the shear zone while reducing the risk for edge fracture. An emphasis was placed upon machinability and surface quality for the design of the pocket in the shear zone.

Compared with urban areas, the road surface in mountainous areas generally has a larger slope, larger curvature and narrower width, and the vehicle may roll over and other dangers on such a road. In the case of limited driver information, if the two cars on the mountain road approach fast, it is very likely to occur road blockage or even collision. Multi-vehicle cooperative control technology can integrate the driving data of nearby vehicles, expand the perception range of vehicles, assist driving through multi-objective optimization algorithm, and improve the driving safety and traffic system reliability. Most existing studies on cooperative control of multiple vehicles is mainly focused on urban areas with stable environment, while ignoring complex conditions in mountainous areas and the influence of driver status. In this study, a digital twin based multi-vehicle cooperative warning system was proposed to improve the safety of multiple vehicles on mountain roads.

As a key tool to maintain urban cleanliness and improve the road environment, road cleaning vehicles play an important role in improving the quality of life of residents. However, the traditional road cleaning vehicle requires the driver to monitor the situation of road garbage at all times and manually operate the cleaning process, resulting in an increase in the driver 's work intensity. To solve this problem, this paper proposes a road garbage recognition algorithm based on improved YOLOv5, which aims to reduce labor consumption and improve the efficiency of road cleaning. Firstly, the lightweight network MobileNet-V3 is used to replace the backbone feature extraction network of the YOLOv5 model. The number of parameters and computational complexity of the model are greatly reduced by replacing the standard convolution with the deep separable convolution, which enabled the model to have faster reasoning speed while maintaining higher accuracy.

To improve the braking energy recovery rate of pure electric garbage removal vehicles and ensure the braking effect of garbage removal vehicles, a strategy using particle swarm algorithm to optimize the regenerative braking fuzzy control of garbage removal vehicles is proposed. A multi-section front and rear wheel braking force distribution curve is designed considering the braking effect and braking energy recovery. A hierarchical regenerative braking fuzzy control strategy is established based on the braking force and braking intensity required by the vehicle. The first layer is based on the braking force required by the vehicle, based on the front and rear axle braking force distribution plan, and uses fuzzy controllers.

The main objective of platoon control is coordinated motion of autonomous vehicle platooning with small intervehicle spacing while maintaining the same speed and acceleration as the leading vehicle, which can save energy consumption and improve traffic throughput. The conventional platoon control methods are confronted with the problem of manual parameter tuning. In order to addres this isue, a novel bifold platoon control approach leveraging a deep reinforcement learning-based model is proposed, which enables the platoon adapt to the complex traffic environment, and guarantees the safety of platoon. The upper layer controller based on the TD3 tuned PID algorithm outputs the desired acceleration. This integration mitigates the inconvenience of frequent manual parameter tuning asociated with the conventional PID algorithm. The lower layer controller tracks the desired acceleration based on the inverse vehicle dynamics model and feedback control.

Decision-making of lane-change for autonomous vehicles faces challenges due to the behavioral differences among human drivers in dynamic traffic environments. To enhance the performances of autonomous vehicles, this paper proposes a game theoretic decision-making method that considers the diverse Social Value Orientations (SVO) of drivers. To begin with, trajectory features are extracted from the NGSIM dataset, followed by the application of Inverse Reinforcement Learning (IRL) to determine the reward preferences exhibited by drivers with distinct Social Value Orientation (SVO) during their decision-making process. Subsequently, a reward function is formulated, considering the factors of safety, efficiency, and comfort. To tackle the challenges associated with interaction, a Stackelberg game model is employed.

The phenomenon of liquid transfer in the liquid tank of the semi-trailer vehicle for transporting dangerous cargo (SVTDC) during braking is analyzed and the relevant mathematical model is established. The braking dynamic model of the SVTDC considering the liquid sloshing in the tank is established, and the model is verified based on the co-simulation method. Based on the typical conditions, the braking deceleration and axle load calculation functions of the model are simulated and analyzed, and the application prospect of the model in the development of driving automation control strategy is discussed.

The characterization of sheet metals under in-plane uniaxial bending is challenging due to the aspect ratios involved that can cause buckling. Anti-buckling plates can be employed but require compensation for contact pressure and friction effects. Recently, a novel in-plane bending fixture was developed to allow for unconstrained sample rotation that does not require an anti-buckling device. The objective of the present study is to design the sample geometry for sheared edge fracture characterization under in-plane bending along with a methodology to resolve the strains exactly at the edge. A series of virtual experiments were conducted for a 1.0 mm thick model material with different hardening rates to identify the influence of gage section length, height, and the radius of the transition region on the bend ratio and potential for buckling. Two specimen geometries are proposed with one suited for constitutive characterization and the other for sheared edge fracture.

Electrical steel, also known as silicon steel, is a ferromagnetic material that is often used in electric vehicles (EVs) for stator and rotor applications. Since the design and manufacturing of rotors require the use of laminated thin electrical steel sheets, the fatigue characterization of these single sheets is of interest. In this study, a 0.27mm thick non-oriented electrical steel sheet was tested under cyclic loading in the load-controlled mode with the load ratio R = 0.1 at room temperature. The specimens were prepared using the Computer Numerical Control (CNC) machining method. The Smith-Watson-Topper mean stress correction was used to find the equivalent fully reversed stress-life (S-N) curve. The Basquin equation was used to describe the fatigue strength of the electrical steel and the fatigue parameters were extracted. Furthermore, a design curve with a reliability of 90% and a confidence level of 90% was generated using Owen’s Tolerance Limit method.

Strict environmental regulations are driving the automotive industry toward electric vehicles as they offer zero emissions. A key component in electric vehicles is the electric motor, where the stator and rotor are manufactured from stacks of thin electrical steel sheets. The electrical steel sheets can be cut in different ways, and the cutting methods may significantly affect the fatigue strength of the component. It is important to understand the effect of the cutting processes on the fatigue properties of electrical steel to ensure there is no premature failure of the electric motor resulting from an improper cutting process. This investigation compared the effect of three different edge preparation methods (stamping, CNC machining, and waterjet cutting) on the fatigue performance of 0.27mm thick electrical steel sheets. To investigate the effect of the edge finish on fatigue behavior, surface roughness was measured for these different samples.

With the development of highway transportation and automobile industry technology, highway truck overload phenomenon occurs frequently, which poses a danger to road safety and personnel life safety. So it is very important to identify the overload phenomenon. Traditionally, static detection is adopted for overload identification, which has low efficiency. Aiming at this phenomenon, a dynamic overload identification method is proposed. Firstly, the coupled road excitation model of vehicle speed and speed bump is established, and then the 4-DOF vehicle model of half car is established. At the same time, considering that the double input vibration of the front and rear wheels will be coupled when vehicle passes through the speed bump, the model is decoupled. Then, the vertical trajectory of the body in the front axle position is obtained by Carsim software simulation.

At present, the development of autonomous driving technology is still immature, and there is still a long way until fully driverless vehicles. Therefore, the state of the driver is still an important factor affecting traffic safety, and it is of great significance to detect the driver’s distracted behavior. In the task of driver distracted behavior detection, some characteristics of driver behavior in the cockpit can be further utilized to improve the detection performance. Compared with general human behaviors, driving behaviors are confined to enclosed space and are far less diverse. With this in mind, we propose a sparse spatiotemporal transformer which extracts local spatiotemporal features by segmenting the video at the low level of the model, and filters out local key spatiotemporal information associated with larger attention values based on the attention map in the middle layer, so as to enhance the high-level global semantic features.

In the Formula Student Electric China (FSEC), the body structure is generally divided into two types, truss steel tube body and carbon fiber load-bearing body (monocoque). The monocoque is loved by Formula Student teams around the world because it has a higher stiffness and lighter weight than the truss steel tube body. With the widespread application of monocoque, it also brings more problems. Due to the use of the monocoque, the connection between each component and the body was changed from the welding of the original truss steel pipe frame to a bolted connection. However, the bolted connection will provide a large preload force to the monocoque, resulting in the monocoque easily crushed in the local, so it is necessary to pre-bury an enhanced part in the monocoque to ensure the connection strength, that is, the embedded part. At present, aluminum plug-ins after topological hollow processing are being used.

A flow channel design of the battery liquid cooling plate is carried out through the variable density topology optimization method according to the heat dissipation requirements of lithium-ion power batteries under actual working conditions. Firstly, given the non-uniform heat generation of lithium battery cells, the heat generation mechanism is studied so that the battery electro-thermal model is established, then the distribution regularity of heat generation rate in the cell at different discharge rates is obtained. Subsequently, through COMSOL Multiphysics simulation software, the multi-objective topology optimization of the primary configuration radiator is conducted. The weights of the optimization objectives minimum temperature and minimum flow resistance are determined by practical engineering application. Finally, an optimized model with a volume fraction of 50% was obtained.

Electrical steels are silicon alloyed steels that possess great magnetic properties, making them the ideal material choice for the stator and rotor cores of electric motors. They are typically comprised of laminated stacks of thin electrical steel sheets. An electric motor can reach high temperatures under a heavy load, and it is important to understand the combined effect of temperature and load on the electrical steel’s performance to ensure the long life and safety of electric vehicles. This study investigated the fatigue strength and failure behavior of a 0.27mm thick electrical steel sheet, where the samples were prepared by a stamping process. Stress-control fatigue tests were performed at both room temperature and 150°C. The S-N curve indicated a decrease in the fatigue strength of the samples at the elevated temperature compared to the room temperature by 15-25 MPa in the LCF and HCF regimes, respectively.

Accurate surrounding vehicle motion prediction is critical for enabling safe, high quality autonomous driving decision-making and motion planning. Aiming at the problem that the current deep learning-based trajectory prediction methods are not accurate and effective for extracting the interaction between vehicles and the road environment information, we design a target vehicle intention-aware dual attention network (IDAN), which establishes a multi-task learning framework combining intention network and trajectory prediction network, imposing dual constraints. The intention network generates an intention encoding representing the driver’s intention information. It inputs it into the attention module of the trajectory prediction network to assist the trajectory prediction network to achieve better prediction accuracy.

At present, most of the game decision lane-changing models only consider the state data of the vehicle at the current moment. However, the driving style has a significant impact on the vehicle trajectories, which should be taken into account in the lane-changing process. Moreover, most of the game models are static and do not take into account the sequence of the vehicle lane-changing. This paper proposed a Stackelberg-game-based vehicle lane-changing model considering driving style. Firstly, the NGSIM public dataset is selected for this research and the data screen flow is processed. The K-means algorithm is applied to exchange data clustering. Based on the analysis of vehicle lane changing features under different driving style, the characteristics of the corresponding data under different style are extracted. The quantic-polynomial programming algorithm is used to generate a vehicle lane changing trajectory under different driving styles.

The battery liquid cooling system can ensure that the battery works within a suitable temperature range, improve the safety performance of the battery system, and ensure the cruising range. This paper introduces a design scheme of a stamped double-parallel liquid cooling plate. Based on the STAR-CCM+ simulation software, a thermal simulation model of the battery management system is established to analyze the thermal behavior of the battery system and to study the effect of the inlet mass flow rate on the temperature of the top surface of the batteries. At the same time, with the analysis of the proportion of pressure drop of each component in the liquid cooling plate, an optimization of inserted part in the liquid cooling plate is proposed. The numerical analysis results are compared with the experimental results of the pressure drop to improve the effectiveness of the optimization scheme.

Dangerous driving behavior will cause serious traffic accidents, which will not only threaten life and property but also cause traffic congestion and reduce road capacity. Speed detection is an important detection method to identify whether a driver is driving dangerously. Traditional speed detection methods need additional sensors, which will increase the cost of speed measurement. This paper proposes a vehicle speed estimation algorithm based on the imaginary projection plane (IPP). The IPP will be established according to the height, field angle, and vertical tilt angle of the camera and will be used to establish the mapping relationship between the world coordinates and image coordinates of the vehicle. By combining YOLOv4 and DeepSORT, the vehicle license plate is detected and tracked, and the center point of the vehicle license plate is taken as the feature point of vehicle speed estimation. The vehicle speed is estimated according to the IPP.