Search Results

Gear whine in 1st and 2nd gears in a new rear wheel drive automatic transmission was identified as a potential customer dis-satisfier. Improvements to the vehicle system were implemented, but did not sufficiently reduce the noise. CAE modeling and hardware testing were used for gear tooth optimization, transmission system, driveline, and vehicle system studies. The planetary gears were re-designed with increased contact ratio, and significant interior noise reduction was achieved; but some vehicles still had excessive noise due to gear parameter variability from multiple sources. Using a DOE and statistical studies, a set of gear parameter targets were identified within the tolerances of the design, which achieved the program objectives for noise.

For the past decade or so, automotive entertainment subsystem architectures have consisted of a simple Human Machine Interface (HMI), AM-FM tuner, a tape deck, an amplifier and a set of speakers. Over time, as customer demand for more entertainment features increased, automotive entertainment integrators made room for new features by allowing for the vertical integration of analog audio and adding a digital control. The new digital control came to entertainment subsystems via a low-speed multiplexing scheme embedded into the entertainment subsystem components, allowing remote control of these new features. New features were typically incorporated into the entertainment subsystem by independently packaging functional modules. Examples of these modules are cellular telephone, Compact Disc Jockey (CDJ), rear-seat entertainment, Satellite Digital Audio Radio System (S-DARS) receiver, voice and navigation with its associated display and hardware.

High-dilution stratified EGR combustion system operating at stoichiometric air-fuel ratio (A/F) could offer significant fuel economy saving comparable to the lean burn or stratified charge direct injection SI engines, while still complies with stringent emission standards by using the conventional three-way catalytic converter. The most critical challenge is to keep substantial separation between EGR gas and air-fuel mixture, or to minimize the mixing between these two zones to an acceptable level for stable and complete combustion. Swirl-type stratified EGR and air-fuel flow structure is considered desirable for this purpose, because the circular engine cylinder tends to preserve the swirl motion and the axial piston movement has minimal effect on the flow structure swirling about the same axis. In this study, KIVA3V was used to simulate mixing and combustion processes in a typical pent-roof gasoline engine cylinder during compression and expansion strokes.

A low-pressure CO2-based climate-control system has the environmental benefits of CO2 refrigerant but avoids the extremely high pressures of the transcritical CO2 cycle. In the new cycle, a liquid “cofluid” is circulated in tandem with the CO2, with absorption and desorption of CO2 from solution replacing condensation/gas cooling and evaporation of pure CO2. This work compares the theoretical performance of the cycle using two candidate cofluids: N-methyl-2-pyrrolidone and acetone. The optimal coefficient of performance (COP) and refrigeration capacity are discussed in terms of characteristics of the CO2-cofluid mixture. Thermodynamic functions are determined either from an activity coefficient model or using the Soave equation of state, with close agreement between the two approaches. Reductions in COP due to nonideal compressor and heat exchangers are also estimated.

Environmental concerns have spawned renewed interest in naturally occurring refrigerants such as carbon dioxide. CO2 has attractive features such as high enthalpy of evaporation and low cost compared to halocarbons. However, the vapor pressure of CO2 is high at temperatures normally encountered in refrigeration and air conditioning systems when compared to traditional and alternative refrigerants such as CFC-12 and HFC-134a. Major research efforts are underway to investigate the transcritical CO2 cycle, in which a gas cooler instead of a condenser accomplishes heat rejection to ambient, since carbon dioxide in this cycle is above the critical point. The vapor pressure in the gas cooler may exceed 120 bar (1,740 lb/in2). In this paper a reduced pressure carbon dioxide system is revisited1, 2. The working fluid is a mixture of CO2 and a non-volatile liquid, referred to as a co-fluid, in which CO2 is highly soluble and readily absorbed and desorbed.

Pressures to increase the recyclable and recycled content of passenger vehicles are accelerating. In Europe, there is interest in eliminating halogenated polymers. Globally, more and more concern is focused on materials and methods that are ecologically friendly. Automakers and their suppliers are being encouraged to design and assemble components in new ways to facilitate separation, identification, and resource recovery at the end of the vehicle’s useful life - something that is not only good for the environment, but also the bottom line. One area of the vehicle that has proved challenging for applying such design for disassembly and recycling (DFD/R) principles has been the interior, owing to the sheer number of materials used there, and the great number of laminate structures that make disassembly nearly impossible. A good example is a door panel inner, which typically consists of a rigid plastic substrate, a foam pad, and a vinyl, leather, or cloth covering.

The objective of the present work was to establish a correlation between steering pump cam ring profile location and steering system performance for noise, vibration and harshness (NVH). Once this correlation was established, the secondary objective was to determine acceptable cam profile position tolerances from the standpoint of NVH performance. These objectives were accomplished through the use of binaural measurement and jury evaluation of vehicle interior noise. Cam rings were manufactured for this study with profiles shifted a predetermined distance away from the nominal position. These cams were built into steering pumps and these pumps were in turn installed in a vehicle. Vehicle interior noise and pump housing vibration measurements were made to quantify the steering system noise performance associated with each cam ring. The interior noise recordings were played back for a jury comprised of engineers familiar with steering system noise.

The work described in this paper was carried out on a specialist engine dynamometer which allows accurate simulation of in-vehicle conditions. This is achieved by the use of a clutch between the engine and dynamometer which allows realistic simulation of gearchanges. The presence of a clutch means that the dynamometer has two distinct modes of operation, corresponding to a engaged or disengaged clutch. This paper describes the design of a speed control scheme, providing bumpless transfer between two controllers, which has been developed to satisfy the differing control requirements of disengaged and engaged operation. Brief discussion of the controllers and bumpless transfer scheme is followed by presentation of test results. Finally, the performance of this scheme is compared with that of an existing hardware controller.

Carbon dioxide (CO2)-based refrigeration systems have been proposed as environmentally benign alternatives to current automotive air conditioners. The CO2 vapor-compression system requires very high operating pressures and complicated control strategies. Recent experimental results indicate that operating pressures comparable to those of current automotive air conditioners can be attained by the inclusion of a secondary carrier fluid (a “co-fluid”), with solution and desolution of the CO2 from the co-fluid substituting for condensation and vaporization of pure CO2. In this work, modeling tools have been developed to optimize the CO2/co-fluid cycle, including the selection of a co-fluid, the CO2/co-fluid ratio (the “loading”), and the operating conditions.

Environmental concerns have spawned renewed interest in naturally occurring refrigerants such as carbon dioxide. CO2 has attractive features such as high enthalpy of evaporation and low cost compared to halocarbons. However, the vapor pressure of CO2 is high at temperatures normally encountered in refrigeration and air conditioning systems when compared to traditional and alternative refrigerants such as CFC-12 and HFC-134a. Major research efforts are underway to investigate the transcritical CO2 cycle, in which a gas cooler instead of a condenser accomplishes heat rejection to ambient, since carbon dioxide under these conditions is above the critical point. The vapor pressure in the gas cooler may exceed 120 bar (1,740 lb/in2). In this paper a reduced pressure carbon dioxide system is reported (Ref 1). Two companion papers will address properties of working fluids (Ref 2) and thermodynamic and cycle models (Ref 3) for the low pressure carbon dioxide cycle.

Microprocessors and microcontrollers are now widely used in automobiles. Microprocessor systems contain sources of interrupt and interrupt service routines, which are software components executed in response to the assertion of an interrupt in hardware. A major problem in designing the software of microprocessor systems is the analytical treatment of interrupt latency. Because multiple interrupt service routines are executed on the same CPU, they compete for the CPU and interfere with each other's latency requirements. Here, interrupt latency is defined as the delay between the assertion of the interrupt in hardware and the start of execution of the associated interrupt service routine. It is estimated that 80% of intermittent bugs in small microprocessor software loads are due to improper treatment of interrupts. Until this work, there is no analytic method for analyzing a particular system to determine if it may violate interrupt latency requirements.

Fuel Vapor Storage Systems (FVSS) on automobiles are susceptible to particle contamination. This is especially true for FVSS components mounted under the automobiles (undercarriage, chassis frame, etc.) and required to meet stringent EPA standards. Particle contamination significantly increases system restriction and reduces the effectiveness of FVSS. This paper describes a dust separator/filter developed to protect the FVSS. Accelerated field durability evaluations and measurement techniques were developed to identify clean locations, ingested contamination levels and ingested contaminant size distributions. Based on field evaluations, test methods were developed in the lab to evaluate effectiveness of several devices to control and reduce contamination. The dust separator design developed was a combination of baffle separators in series with an open cell foam filter. The dust separator was designed to meet and exceed several vehicle system design requirements.

Significant interest in high intensity discharge headlamps (HID) has been developing in the past few years. It evolved as a safety device in the high-end luxury automobile segments, and is now showing demand for applications in other vehicle lines as well. However, affordability of these systems has been a continuous problem for all vehicle lines. A headlamp system that consists of: a remotely located light collector integrated to an HID source and ballast, a pair of light cables and distribution optics at the output of the light cables is being presented as a low cost alternative to HID headlamps. It also offers significant reductions in vehicle power consumption and radically new styling options. Five different concepts for light distribution optics will be discussed along with their performance compared to conventional HID and halogen headlamps.

Visteon Automotive Systems has developed an Electro-Hydraulic Power Assist Steering (EHPAS) System. This low-cost system uses conventional hydraulic power steering components with an electrically-driven and electronically-controlled power steering pump. This paper presents the Visteon EHPAS system and its development process. This process began with analytical modeling of the EHPAS system and integration of these models with a two degree of freedom (2DOF) vehicle model. These models were critical for system analysis and control strategy design. The EHPAS system sizing procedure and control strategy performance optimization were verified with the use of a real-time computer designed by Ford Motor Company, and by specially-designed Visteon test benches. Finally, EHPAS equipped test vehicles were tuned for high performance, providing better feel and fuel economy than conventionally equipped base line vehicles.

The scratch resistance of automotive plastic coatings has been studied extensively over the past few years. Most testing methodology to correlate damage of the coating to field conditions has been in the form of small particulate wearing, e.g., alumina oxide abrasive, or indentation resistance of the coating to an external probe, e.g., a nanoindentation device. The subsequent damage imparted to the coating has generally been analyzed by the amount of coating mass lost in the wear event or through a ratio of optical reflectance of the damaged area to the undamaged surface. In this paper, we attempt to delineate surface damage resistance of several automotive clearcoats through an optical interferometry methodology developed to measure volume and depth of damage incurred with small particle alumina oxide erodents in a simulated wear environment.