Search Results

Bushing elasticity is one of the most important compliance factors that significantly influence driving behavior. The deformations of the bushings change the wheel orientations under external forces. Another important factor of bushing compliance is to provide a comfortable driving experience by isolating the vibrations from road irregularities. However, the driving comfort and driving dynamics are often in conflict and need to be balanced in terms of bushing compliance design. Specifically, lateral force steer and brake force steer are closely related to safety and stability and comprises must be minimized. The sensitivity analysis helps engineers to understand the critical bushing for certain compliance attributes, but optimal balancing is complicated to understand. The combination of individual bushing stiffness must be carefully set to achieve an acceptable level of all the attributes.

We describe experiments and numerical modeling of snow surface contamination on two simplified automotive bluff bodies: The Ahmed body and a wedge. The purpose was twofold: 1) To obtain well defined experimental results of snow contamination on simple geometries; 2) To propose a numerical modeling approach for snow contamination. The experiments were performed in a climatic wind tunnel using a snow cannon at −15 °C and the results show that the snow accumulation depends on the aerodynamics of the studied bluff bodies. Snow accumulates on surfaces in proximity to the aerodynamic wakes of the bodies and characteristic snow patterns are obtained on side surfaces. The numerical modeling approach consisted of an aerodynamic setup coupled with Lagrangian particle tracking. Particles were determined to adhere or rebound depending on an adhesion model combined with a resuspension criterion.

Squeak and rattle (S&R) are nonstationary annoying and unwanted noises in the car cabin that result in considerable warranty costs for car manufacturers. Introduction of cars with remarkably lower background noises and the recent emphasis on electrification and autonomous driving further stress the need for producing squeak- and rattle-free cars. Automotive manufacturers use several road disturbances for physical evaluation and verification of S&R. The excitation signals collected from these road profiles are also employed in subsystem shaker rigs and virtual simulations that are gradually replacing physical complete vehicle test and verification. Considering the need for a shorter lead time and the introduction of optimisation loops, it is necessary to have efficient and inclusive excitation load cases for robust S&R evaluation.

The aim of the presented research is to propose and benchmark two brake models, namely the novel dynamic ILVO (Ilmenau-Volvo) model and a neural-network based regression. These can estimate the evolution of the brake friction between pad and disc under different load conditions, which are typically experienced in vehicle applications. The research also aims improving the knowledge of the underlying mechanism related to the evolution of the BLFC (boundary layer friction coefficient), the reliability of virtual environment simulations to speed up the product development time and reducing the amount of vehicle test in later phases and finally improving brake control functions. With the support of extensive brake dynamometer testing, the proposed models are benchmarked against State-of-the-Art. Both approaches are parametrized to render the friction coefficient dynamics with respect to the same input parameters.

Increasing demand for simulation accuracy often leads to increased finite element model complexity, which in turn, results in higher computational costs. As a provision, component mode synthesis approaches are employed to approximate the system response by using dynamic substructuring and model reduction techniques in linear systems. However, the use of available model reduction techniques in nonlinear problems containing the contact type of nonlinearities remains an interesting topic. In this paper, the application of a component mode synthesis method in squeak and rattle nonlinear simulation has been investigated. Critical regions for squeak and rattle of the side door model of a passenger car were modelled by nonlinear contact definition in finite element simulation. Craig-Bampton model reduction method was employed to substructure the finite element model while keeping the nonlinear contacts in the model.

The need for a more complete understanding of the flow behavior in aerodynamic wind tunnels has increased as they have become vital tools not only for vehicle development, but also for vehicle certification. One important aspect of the behavior is the empty test section flow, which in a conventional tunnel should be as uniform as possible. In order to assess the uniformity and ensure consistent behavior over time, accurate measurements need to be performed regularly. Furthermore, the uncertainties and errors of the measurements need to be minimized in order to resolve small non-uniformities. In this work, the quantification of the measurement uncertainties from the full measurement chain of the new flow uniformity measurement rig for the Volvo Cars aerodynamic wind tunnel is presented. The simulation based method used to account for flow interference of the probe mount is also discussed.

In aerodynamic development of ground vehicles, the use of Computational Fluid Dynamics (CFD) is crucial for improving the aerodynamic performance, stability and comfort of the vehicle. Simulation time and accuracy are two key factors of a well working CFD procedure. Using scale-resolving simulations, accurate predictions of the flow field and aerodynamic forces are possible, but often leads to long simulation time. For a given solver, one of the most significant aspects of the simulation time/cost is the temporal resolution. In this study, this aspect is investigated using the realistic vehicle model DrivAer with the notchback geometry as the test case. To ensure a direct and accurate comparison with wind tunnel measurements, performed at TU Berlin, a large section of the wind tunnel is included in the simulation domain. All simulations are performed at a Reynolds number of 3.12 million, based on the vehicle length.

A two-state forward dynamic programming algorithm is evaluated in a series hybrid drive-train application with the objective to minimize fuel consumption when look-ahead information is available. The states in the new method are battery state-of-charge and engine speed. The new method is compared to one-state dynamic programming optimization methods where the requested generator power is found such that the fuel consumption is minimized and engine speed is given by the optimum power-speed efficiency line. The other method compared is to run the engine at a given operating point where the system efficiency is highest, finding the combination of engine run requests over the drive-cycle that minimizes the fuel consumption. The work has included the engine torque and generator power as control signals and is evaluated in a full vehicle-simulation model based on the Volvo Car Corporation VSIM tool.

1 Turbocharging plays an important role in the downsizing of engines. Model-based approaches for boost control are going to increasing the necessity for controlling the wastegate flow more accurately. In today’s cars, the wastegate is usually only controlled with a duty cycle and without position feedback. Due to nonlinearities and varying disturbances a duty cycle does not correspond to a certain position. Currently the most frequently used feedback controller strategy is to use the boost pressure as the controller reference. This means that there is a large time constant from actuation command to effect in boost pressure, which can impair dynamic performance. In this paper, the performance of an electrically controlled vacuum-actuated waste-gate, subsequently referred to as vacuum wastegate, is compared to an electrical servo-controlled wastegate, also referred to as electric wastegate.

To improve fuel efficiency and facilitate handling of the vehicle in a dense city environment, it should be as small as possible given its intended application. This downsizing trend impacts the size of the engine bay, where the air filter box has to be packed in a reduced space, still without increased pressure drop, reduced load capacity nor lower filtering efficiency. Due to its flexibility and reduced cost, CFD simulations play an important role in the optimization process of the filter design. Even though the air-flow through the filter box changes as the dust load increases, the current modeling framework seldom account for such time dependence. Volvo Car Corporation presents an industrial affordable model to solve the time-dependent dust load on filter elements and calculate the corresponding flow behavior over the life time of the air filter box.

Heat loss is one of the greatest energy losses in engines. More than half of the heat is lost to cooling media and exhaust losses, and they thus dominate the internal combustion engine energy balance. Complex processes affect heat loss to the cylinder walls, including gas motion, spray-wall interaction and turbulence levels. The aim of this work was to experimentally compare the heat transfer characteristics of a stepped-bowl piston geometry to a conventional re-entrant diesel bowl studied previously and here used as the baseline geometry. The stepped-bowl geometry features a low surface-to-volume ratio compared to the baseline bowl, which is considered beneficial for low heat losses. Speed, load, injection pressure, swirl level, EGR rate and air/fuel ratio (λ) were varied in a multi-cylinder light duty engine operated in conventional diesel combustion (CDC) mode.

Flow visualization techniques are widely used in aerodynamics to investigate the surface trace pattern. In this experimental investigation, the surface flow pattern over the rear end of a full-scale passenger car is studied using tufts. The movement of the tufts is recorded with a DSLR still camera, which continuously takes pictures. A novel and efficient tuft image processing algorithm has been developed to extract the tuft orientations in each image. This allows the extraction of the mean tuft angle and other such statistics. From the extracted tuft angles, streamline plots are created to identify points of interest, such as saddle points as well as separation and reattachment lines. Furthermore, the information about the tuft orientation in each time step allows studying steady and unsteady flow phenomena. Hence, the tuft image processing algorithm provides more detailed information about the surface flow than the traditional tuft method.

The aerodynamic drag, fuel consumption and hence CO2 emissions, of a road vehicle depend strongly on its flow structures and the pressure drag generated. The rear end flow which is an area of complex three-dimensional flow structures, contributes to the wake development and the overall aerodynamic performance of the vehicle. This paper seeks to provide improved insight into this flow region to better inform future drag reduction strategies. Using experimental and numerical techniques, two vehicle shapes have been studied; a 30% scale model of a Volvo S60 representing a 2003MY vehicle and a full scale 2010MY S60. First the surface topology of the rear end (rear window and trunk deck) of both configurations is analysed, using paint to visualise the skin friction pattern. By means of critical points, the pattern is characterized and changes are identified studying the location and type of the occurring singularities.

Vehicle dynamics development relies on subjective assessments (SA), which is a resource-intensive procedure requiring both expert drivers and vehicles. Furthermore, development projects becoming shorter and more complex, and increasing demands on quality require higher efficiency. Most research in this area has focused on moving from physical to virtual testing. However, SA remains the central method. Less attention has been given to provide better tools for the SA process itself. One promising approach is to introduce computer-tablets to aid data collection, which has proven to be useful in medical studies. Simple software solutions can eliminate the need to transcribe data and generate more flexible and better maintainable questionnaires. Tablets’ technical features envision promising enhancements of SA, which also enable better correlations to objective metrics, a requirement to improve CAE evaluations.

The focus on engine thermal management is rapidly increasing due to the significant effect of heat losses on fuel consumption, engine performance and emissions. This work presents a time resolved, high resolution 3D engine heat balance model, including all relevant components. Notably, the model calculates the conjugated heat transfer between the solid engine components, the coolant and the oil. Both coolant and oil circuits are simultaneously resolved with a CFD solver in the same finite volume model as the entire engine solid parts. The model includes external convection and radiation. The necessary boundary conditions of the thermodynamic cycle (gas side) are mapped from a calibrated 1D gas exchange model of the same engine. The boundary conditions for the coolant and at the oil circuits are estimated with 1D models of the systems. The model is calibrated and verified with measurement data from the same engine as modeled.

Several of the exterior noise sources existing around a vehicle can cause airborne noise issues at relatively low frequencies. SEA, traditionally used for airborne sound issues is not suitable for the frequency range of interest. Finite Element analysis has been used. Handling of the non-reflecting condition on the outer boundary of the exterior cavity is an issue. Recently, advances have been made in several commercially available codes, which made the analysis practical. Including the poro-elastic material model for foam-based carpets is also becoming practically possible. The purpose of the current study is to investigate the practical applications of those new developments against test data, and to estimate the feasibility of using these procedures in the vehicle development projects. Measurements were carried out in a new semi-anechoic chamber at Volvo Cars. These measurements involved 3 body objects - a Body-in-Blue (BIB) sedan, a Complete Vehicle (CV) sedan and a CV wagon.

The automotive industry strives to develop high quality vehicles in a short period of time that satisfy the consumer needs and stand out in the competition. Full exploitation of simulation and Computer-Aided Engineering (CAE) tools can enable quick evaluation of different vehicle concepts and setups without the need of building physical prototypes. Addressing the aforementioned statements this paper presents a method for optimising the Electric Power-Assisted Steering (EPAS) ECU parameters employing solely CAE. The objective of the optimisation is to achieve a desired steering response. The developed process is tested on three specific steering metrics (friction feel, torque build-up and torque deadband) for two function parameters (basic steering torque and active return) of the EPAS. The optimisation method enabled all metrics to fall successfully within the target range.

Passenger cars equipped with diesel engines will meet challenging emission legislation for the coming decade, with introduction of Euro6 and Euro7, which comprises reduced NOX emissions and possibly new driving cycles including off-cycle limits. The technology measures to meet these legislative limits comprise a broad spectrum of engine and aftertreatment, i.e., engine measures such as improved fuel injection with respect to mass and timing, improved exhaust gas recirculation, improved warm-up and reduced friction, as well as aftertreatment measures such as selective catalytic reduction and lean NOX trap in combination with diesel particulate filter, and the thereby associated engine control. The resulting technology matrix is therefore large, and calls for a multidisciplinary simulation approach for appropriate selection and optimization of technology and control with the objectives and constraints of emissions, fuel consumption, performance and cost.

Automotive turbo compressors generate high frequency noise in the air intake system. This sound generation is of importance for the perceived sound quality of luxury cars and may need to be controlled by the use of silencers. The silencers usually contain resonators with slits, perforates and cavities. The purpose of the present work is to develop acoustic models for these resonators where relevant effects such as the effect of a realistic mean flow on losses and 3D effects are considered. An experimental campaign has been performed where the two-port matrices and transmission loss of sample resonators have been measured without flow and for two different mean flow speeds. Models for two resonators have been developed using 1D linear acoustic theory and a FEM code (COMSOL Multi-physics). For some resonators a separate linear 1D Matlab code has also been developed.

Efforts towards ever more energy efficient passenger cars have become one of the largest challenges of the automotive industry. This involves numerous different fields of engineering, and every finished model is always a compromise between different requirements. Passenger car aerodynamics is no exception; the shape of the exterior is often dictated by styling, engine bay region by packaging issues etcetera. Wheel design is also a compromise between different requirements such as aerodynamic drag and brake cooling, but as the wheels and wheel housings are responsible for up to a quarter of the overall aerodynamic drag on a modern passenger car, it is not surprising that efforts are put towards improving the wheel aerodynamics.