Search Results

This SAE Aerospace Information Report (AIR) provides a comprehensive overview of primary water content measurement instrumentation, for both facility-based icing research and in-flight icing research, over the range of commonly used aircraft certification icing envelopes. It includes information on the theory of operation of the instruments, system errors and limitations, and practical considerations when using them for cloud characterization. This document does not address other icing cloud measurements of interest, such as particle sizing, or measurement of phenomena such as snow, sleet, or hail.

This document provides information regarding ice detector technology and design. The SAE document AS5498 provides detailed information regarding the requirements, specifications, qualification, and certification of icing detection systems. This document is not meant to replace AS5498, but to enhance it by considering unique aspects of sensing technology and, in particular, those that may not be certificated at the time of this revision. To that end, an effort has been made not to duplicate information contained in AS5498. Icing rate information is included where applicable. The primary application is associated with ice forming on the leading edges of airfoils and inlets while the aircraft is in flight. Information related to detection of ice over cold fuel tanks and icing at low-velocity operation is included. The material is primarily applicable to fixed-wing aircraft. Unique requirements for engine inlets and rotorcraft are also provided.

This document contains minimum operational performance specification (MOPS) of active on-board INFLIGHT ICING DETECTION SYSTEMS (FIDS). This MOPS specifies FIDS operational performance which is the minimum necessary to satisfy regulatory requirements for the design and manufacture of the equipment to a minimum standard and guidance towards acceptable means of compliance when installed on an AIRCRAFT. Detection of ICE accreted on the AIRCRAFT during ground operations is not considered in this document. This MOPS was written for the use of FIDS on AIRCRAFT as defined in 1.3 and 2.3. Expected minimum performance specifications for FIDS and their functions are provided in Section 3. The minimum performance requirements as defined in Section 3 do not consider SYSTEM performance as installed on the AIRCRAFT. Performance in excess of the minimum performance may be required by the SYSTEM installed on an AIRCRAFT in order to meet regulatory or operational requirements.

This section presents the basic equations for computing ice protection requirements for nontransparent and transparent surfaces and for fog and frost protection of windshields. Simplified graphical presentations suitable for preliminary design and a description of various types of ice, fog, frost, and rain protection systems are also presented.

This SAE Aerospace Information Report (AIR) identifies and summarizes the various factors that should be considered during design, development, certification, or testing of helicopter rotor blade ice protection systems. Although various concepts of ice protection are mentioned in this report, the text is limited generally to those factors associated with design and substantiation of cyclic electrothermal ice protection systems as applicable to the protection of helicopter rotor blades. Other systems are described briefly in Appendix A. Applications consider main rotor blades, conventional tail rotor blades, and other types of antitorque devices. The information contained in this report is also limited to the identification of factors that should be considered and why the factor is important. Specific design, analysis and test methodologies are not included. For additional information refer to the references listed in 2.1.

This section presents the basic equations for computing ice protection requirements for nontransparent and transparent surfaces and for fog and frost protection of windshields. Simplified graphical presentations suitable for preliminary design and a description of various types of ice, fog, frost, and rain protection systems are also presented.

This SAE Aerospace Information Report (AIR) contains information on most of the major icing simulation ground facilities. An effort was made to obtain data from as many facilities as possible over a two year time period. The data in this document represents the state of the facilities in calendar year 1996. Facilities are constantly changing and upgrading and, therefore, some facility specifications may change during the life of this report. Of the 27 facilities described in this report, the primary use is split with approximately half for engine testing and half for wind tunnel testing. The facilities are limited to ground facilities and, therefore, icing tankers have not been included.

This section presents the basic equations for computing ice protection requirements for nontransparent and transparent surfaces and for fog and frost protection of windshields. Simplified graphical presentations suitable for preliminary design and a description of various types of ice, fog, frost, and rain protection systems are also presented.

This SAE Aerospace Information Report (AIR) identifies and summarizes the various factors that should be considered during design, development, certification, or testing of helicopter rotor blade ice protection systems. Although various concepts of ice protection are mentioned in this report, the text is limited generally to those factors associated with design and substantiation of cyclic electrothermal ice protection systems as applicable to the protection of helicopter rotor blades. Other systems are described briefly in Appendix A. Applications consider main rotor blades, conventional tail rotor blades, and other types of antitorque devices. The information contained in this report is also limited to the identification of factors that should be considered and why the factor is important. Specific design, analysis and test methodologies are not included. For additional information refer to the references listed in 2.1.

This Icing Technology Bibliography is a compendium of references from the open literature that were published prior to the original 1987 issuance of the AIR, including both national and foreign sources. Due to the generality of the subject, and the difficulty of fully investigating every available source, the Bibliography in this document is not intended to be complete.

This document provides information regarding ice detector technology, design and operating requirements. The SAE document AS5498 provides detailed information regarding the requirements, specifications, qualification, and certification of icing detection systems. This document is not meant to replace AS5498 but to enhance it by considering unique aspects of sensing technology and in particular those that may not be certificated at the time of this revision. To that end an effort has been made not to duplicate information contained in AS5498. Icing rate information is included where applicable. The primary application is associated with ice forming on the leading edges of airfoils and inlets while the aircraft is in flight. Information related to detection of ice over cold fuel tanks and icing at low velocity operation is included. The material is primarily applicable to fixed-wing aircraft. Unique requirements for engine inlets and rotorcraft are also provided.

The objective of this Minimum Operational Performance Specification is to specify the minimum performance of onboard inflight icing detection systems. Throughout the document, these devices are referred to as Flight Icing Detection Systems (FIDS). These systems are intended to either provide information which indicates the presence of ice accreted in flight on monitored surfaces or indicate the presence of icing conditions in the atmosphere. They may operate the airplane anti-ice/ deice systems. Detection of ice accreted on the ground is not considered in this document but can be found in ED-104. This MOPS was written for the use of FIDS on airplanes only, as defined in paragraph 1.5. Use on other aircraft may require additional considerations. Chapter 1 of this document provides information required to understand the need for the equipment characteristics and tests defined in the remaining chapters.

This Icing Technology Bibliography is a compendium of references from the open literature that were published prior to the original 1987 issuance of the AIR, including both national and foreign sources. Due to the generality of the subject, and the difficulty of fully investigating every available source, the Bibliography in this document is not intended to be complete.

This section presents the basic equations for computing ice protection requirements for nontransparent and transparent surfaces and for fog and frost protection of windshields. Simplified graphical presentations suitable for preliminary design, and a description of various types of ice, fog, frost, and rain protection systems are also presented.

This SAE Aerospace Information Report (AIR) contains information on most of the major icing simulation ground facilities. An effort was made to obtain data from as many facilities as possible over a two year time period. The data in this document represents the state of the facilities in calendar year 1996. Facilities are constantly changing and upgrading and, therefore, some facility specifications may change during the life of this report. Of the 27 facilities described in this report, the primary use is split with approximately half for engine testing and half for wind tunnel testing. The facilities are limited to ground facilities and, therefore, icing tankers have not been included.

This specification covers the general requirements for the design, installation, and performance of thermal anti-icing equipment for the wings and empennage surfaces in aircraft.

This Icing Technology Bibliography is a compendium of references from the open literature, including both national and foreign sources. Due to the generality of the subject, and the difficulty of fully investigating every available source, the present Bibliography is not intended to be complete. However, it will be updated every 18 months by the SAE AC-9C Aircraft Icing Technology Subcommittee. Any suggestions in terms of additional references, sources, and corrections should be referred to the Icing Technology Bibliography Panel of the SAE AC-9C Aircraft Icing Technology Subcommittee.

This Aerospace Information Report (AIR) identifies and summarizes the various factors that should be considered during design, development, certification, or testing of helicopter rotor blade ice protection. Although various concepts of ice protection are mentioned in this report, the text is limited generally to those factors associated with design and substantiation of cyclic electrothermal ice protection systems as applicable to the protection of helicopter rotor blades. Other systems are described briefly in Appendix A. Applications consider main rotor blades, conventional tail rotor blades, and other types of antitorque devices. The information contained in this report is also limited to the identification of factors that should be considered and why the factor is important. Specific design, analysis and test methodologies are not included. For additional information refer to the references in Section 7.

This document provides information regarding ice detector technology, and design and operating requirements. Icing rate information is included where applicable. The primary application is associated with ice forming on the leading edges of airfoils and inlets with significant forward velocities. Information related to detection of ice at static conditions, ice over cold fuel tanks, and icing at low velocity operation is also included. The material is primarily applicable to transport and light aircraft. Special consideration for rotorcraft is appended separately.