Refine Your Search

Date

Date

Topic

Topic

Glass Weather and climate Identification Plating AMS CE Elastomers Committee

Search Results

Viewing 1 to 20 of 584
123Next >Last >>
Sort by published
Standard

Identification and Packaging Elastomeric Products
2024-03-04
CURRENT
AMS2810J
This specification provides requirements for the identification and packaging of sheet, strip, extrusions, and molded parts made of natural rubber, synthetic rubber, reclaimed rubber, and combinations of the above with other materials such as asbestos, cork, and fabrics. AMS2817 covers preferred requirements for identification and packaging of preformed packings.
Standard

Elastomer: Fluorosilicone Rubber (FVMQ), Fuel and Oil Resistant, High Strength, 45 – 55 Shore A Hardness, For Products in Fuel Systems / Lubricating Oils
2023-10-16
CURRENT
AMS3329D
This specification covers a high strength fluorosilicone (FVMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-ring cord, and molded in place gaskets for aeronautical and aerospace applications.
Standard

Elastomer: Chloroprene Rubber (CR) Weather Resistant 55 - 65
2022-06-13
CURRENT
AMS3241K
This specification covers a chloroprene (CR) rubber that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes such as window channels, bumper pads, chafing strips, etc. For molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the equivalent AMS7XXX specification.
Standard

Elastomer: Chloroprene Rubber (CR) Weather Resistant 35 - 45
2022-06-13
CURRENT
AMS3240L
This specification covers a chloroprene rubber (CR) that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes such as window channels, bumper pads, chafing strips, etc. For molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the equivalent AMS7XXX specification.
Standard

Packaging and Identification of Molded Elastomeric Seals and Sealing Components
2022-05-20
CURRENT
AMS2817G
This specification covers procedures which will provide protection of elastomeric seals and seal assemblies such as O-rings, cap seal assemblies, and other designs from contamination by foreign materials and handling / transportation / storage damage prior to installation and ensure positive identification by part number of each piece until it is installed.
Standard

Sponge, Chloroprene (CR) Rubber, Soft
2022-03-01
CURRENT
AMS3197N
This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered.
Standard

Rubber, Ethylene-Propylene, Hydrazine Resistant
2021-07-21
WIP
AMSR83412B
This specification covers three types of rubber having good resistance to high and low temperature and hydrazine type propellants, but poor resistance to hydrocarbon oils or solvents. Hydrazines are hazardous chemicals. See Dangerous Properties of Industrial Materials; by N. Irving Sax.
Standard

Rubber: Vinyl-Methyl Silicone (VMQ) Hot Air Resistant Low Compression Set, 70 to 80 Type A Hardness for Seals in Hot Air Systems
2021-05-19
CURRENT
AMS7267H
This specification covers a silicone (VMQ) rubber in the form of molded rings. These rings have been used typically as sealing rings for service from -65 to +260 °C (-85 to +500 °F) in contact with air, but usage is not limited to such applications. The cross-section of such rings is usually not over 0.275 inch (6.98 mm) in diameter or thickness.
Standard

Designing with Elastomers for use at Low Temperatures, Near or Below Glass Transition
2020-11-12
WIP
AIR1387E

To ensure success in design of elastomeric parts for use at low temperature, the design engineer must understand the peculiar properties of rubber materials at these temperatures.

There are no static applications of rubber. The Gaussian theory of rubber elasticity demonstrates that the elastic characteristic of rubber is due to approximately 15% internal energy and the balance, 85%, is entropy change. In other words, when an elastomer is deformed, the elastomer chain network is forced to rearrange its configuration thereby storing energy through entropy change. Thermodynamically, this means that rubber elasticity is time and temperature dependent (Reference 25).

The purpose of this report is to provide guidance on low temperature properties of rubber with the terminology, test methods, and mathematical models applicable to rubber, and to present some practical experience.

123Next >Last >>
X