Search Results

One of the main challenges related to the use of Hydrogen in Internal Combustion Engines is the trade-off between NOx emissions and brake power output: on the one hand, a lean premixed charge (Lambda ≈2.5) is generally able to provide a regular and efficient combustion, yielding near-zero NOx emissions; on the other hand, the power density tends to be very poor, due to the huge amount of air required by the thermodynamic process. As a further penalization, the injection of a gaseous fuel during the intake process has a negative impact on volumetric efficiency. Supercharging can be a solution for addressing the problem, but at the cost of an increase of complexity, cost and overall dimensions. An alternative path is represented by the 2-stroke cycle, and, in particular, by the opposed piston (OP) design. Most of the existing OP engines are compression ignited, but Spark ignition and direct fuel injection can be implemented without relevant modifications to the layout of cylinders.

The paper presents a preliminary study on a virtual 2-stroke 3-cylinder 0.9 L DI SI supercharged engine running on Hydrogen (H2), able to meet both high performance targets and ultra-low emissions limits (NOx<20 ppm). Combustion is similar to a conventional 4-stroke H2 DI engine, while the design of the cylinder and the actuation law of both intake and exhaust valves are specifically optimized for the 2-stroke cycle. In comparison to a more conventional 2-stroke loop scavenged engine, with piston-controlled ports, the use of poppet valves enables a more flexible control of the gas exchange process and to maintain the same design of a 4-stroke engine for pistons, cylinders block, crankcase and lubrication system. On the other hand, it is more difficult to avoid the short-circuit of the fresh charge, while permeability of the valves becomes quite critical at high engine speed.

Alcohol-based fuels are a viable alternative to fossil fuels for powering vehicles. As a drop-in fuel, an oxygenated fuel blend containing the C8 alcohol 2-ethylhexanol (isomer of octanol), hydrotreated vegetable oil (HVO) and rapeseed methyl ester (RME) can reduce soot and NOx emissions whilst maintaining engine performance. However, fuel injection strategy significantly affects combustion and hence has been investigated with a view to reducing emissions whilst maintaining engine efficiency. In a single cylinder light-duty compression ignition research engine, the effect of different injection strategies (main, main/post, double pre/main, double pre/main/post injection) and EGR levels (0%, 19%) on specifically NOx, soot emissions and particle size distribution was investigated for three different fuels: fossil diesel fuel, HVO and the oxygenated blend. The blend was designed to have diesel-like combustion properties (cetane number of 52) and had an oxygen content of 5.4% by mass.

The motor generator unit installed on the turbocharger shaft (MGU-H) provides a fundamental contribution to the amazing performances and efficiency of the last Formula 1 power units. The excess of exhaust gas energy - normally dumped through the waste-gate - can be converted into electric energy and used to push the car, by means of a second motor generator unit installed on the engine crankshaft (MGU-K). The goal of this paper is to assess pros and cons of the MGU-H technology when applied to a family of engines of different displacement, installed on a typical passenger car. The influence of engine size and cylinders layout is investigated, under the same set of hypotheses, considering both transient and steady engine operations. The baseline engine is a commercial 2.0 L, SI, 4-cylinder in-line, rated at 200 HP at 4500-5000 rpm.

The new Stage 5 European regulation for Non Road Mobile Machinery has lowered the limits on pollutant emissions for all the categories of internal combustion engines. An interesting alternative to the implementation of sophisticated after-treatment systems is to downsize the engine, and provide the extra power for peak demands with an electric motor, installed in place of the flywheel. The paper explores the potential of this concept, applied to an industrial engine, manufactured by Kohler, and delivering a maximum power of 56 kW@2600 rpm. The study is supported by a comprehensive experimental characterization of the internal combustion engine and of the electric components. A representative duty cycle is also defined, on the basis of a set of measures, taken in real operating conditions. The analysis of this reference cycle is performed by using a GT-Suite model, comparing different power split strategies.

The paper reviews the CFD optimization of a motorcycle engine, modified for the development of a hybrid powertrain of a Formula SAE car. In a parallel paper, the choice of the donor engine (Ducati 959 Panigale: 2-cylinder, V90, 955 cc, peak power 150 HP at 10500 rpm, peak torque 102 Nm at 9000 rpm) is thoroughly discussed, along with all the hardware modifications oriented to minimize the new powertrain dimensions, weight and cost, and guarantee full reliability in racing conditions. In the current paper, the attention is focused on two main topics: 1) CFD-1D tuning of the modified Internal Combustion Engine (ICE), in order to comply with the Formula SAE regulations, as well as to maximize the power output; 2) simulation of the vehicle in racing conditions, comparison with a conventional combustion car and a full electric vehicle.

Spray characteristics of fossil Diesel fuel, hydrotreated vegetable oil (HVO) and two oxygenated fuel blends were studied to elucidate the combustion process. The fuels were studied in an optically accessible high-pressure/high-temperature chamber under non-combusting (623 K, 4.69 MPa) and combusting (823 K, 6.04 MPa) conditions. The fuel blends contained the long-chain alcohol 2-ethylhexanol (EH), HVO and either 20 vol.% Diesel or 7 vol.% rapeseed methyl ester (RME) and were designed to have a Diesel-like cetane number (CN). Injection pressures were set to 120 MPa and 180 MPa and the gas density was held constant at 26 kg/m3. Under non-combusting conditions, shadow imaging revealed the penetration length of the liquid and vapor phase of the spray. Under combusting conditions, the lift-off length and soot volume fraction were measured by simultaneously recording time-resolved two-dimensional laser extinction, flame luminosity and OH* chemiluminescence images.

The effects of using n-butanol, n-octanol, fossil Diesel, hydrotreated vegetable oil (HVO), and blends of these fuels on spray penetration, flame and soot characteristics were investigated in a high-pressure high-temperature constant volume combustion chamber designed to mimic a heavy duty Diesel engine. Backlight illumination was used to capture liquid and vapor phase spray images with a high-speed camera. The flame lift-off length (LOL) and ignition delay were determined by analyzing OH* chemiluminescence images. Laser extinction diagnostics were used to measure the spatially and temporally resolved soot volume fraction. The spray experiments were performed by injecting fuels under non-combusting (623 K) and combusting (823 K) conditions at a fixed ambient air density of 26 kg/m3. A Scania 0.19 mm single straight hole injector and Scania XPI common rail fuel supply system were used to produce injection pressures of 120 MPa and 180 MPa.

With progressing electrification of automotive powertrains and demands to meet increasingly stringent emission regulations, a combination of an electric motor and downsized turbocharged spark-ignited engine has been recognized as a viable solution. The SI engine must be optimized, and preferentially downsized, to reduce tailpipe CO2 and other emissions. However, drives to increase BMEP (Brake Mean Effective Pressure) and compression ratio/thermal efficiency increase propensities of knocking (auto-ignition of residual unburnt charge before the propagating flame reaches it) in downsized engines. Currently, knock is mitigated by retarding the ignition timing, but this has several limitations. Another option identified in the last decade (following trials of similar technology in aircraft combustion engines) is water injection, which suppresses knocking largely by reducing local in-cylinder mixture temperatures due to its latent heat of vaporization.

The compression ratio is an important engine design parameter. It determines to a large extend engine properties like the achievable efficiency, the heat losses from the combustion chamber and the exhaust losses. The same properties are affected by insulation of the combustion chamber. It is therefore especially important to know the compression ratio when doing experiments with thermal barrier coatings (TBC). In case of porous TBCs, the standard methods to measure the compression ratio can give wrong results. When measuring the compression ratio by volume, using a liquid, it is uncertain if the liquid fills the total porous volume of the coating. And for a thermodynamic compression ratio estimation, a model for the heat losses is needed, which is not available when doing experiments with insulation. The subject of this paper is the evaluation of an alternative method to assess the compression ratio.

Oxygen enriched air (EA) is a well known industrial mixture in which the content of oxygen is higher respect the atmospheric one, in the range 22-35%. Oxygen EA can be obtained by desorption from water, taking advantage of the higher oxygen solubility in water compared to the nitrogen one, since the Henry constants of this two gases are different. The production of EA by this new approach was already studied by experimental runs and theoretical considerations. New results using salt water are reported. EA promoted combustion is considered as one of the most interesting technologies to improve the performance in diesel engines and to simultaneously control and reduce pollution. This paper explores, by means of 3-dimensional computational fluid dynamics simulations, the effects of EA on the performance and exhaust emissions of a high-speed direct-injection diesel engine.

Hybridization is a mainstream technology for automobiles, and its application is rapidly expanding in other fields. Marine propulsion is one such field that could benefit from electrification of the powertrain. In particular, for boats to sail in enclosed waterways, such as harbors, channels, lagoons, a pure electric mode would be highly desirable. The main challenge to accomplish hybridization is the additional weight of the electric components, in particular the batteries. The goal of this project is to replace a conventional 4-stroke turbocharged Diesel engine with a hybrid powertrain, without any penalty in terms of weight, overall dimensions, fuel efficiency, and pollutant emissions. This can be achieved by developing a new generation of 2-Stroke Diesel engines, and coupling them to a state-of-the art electric system. For the thermal units, two alternative designs without active valve train are considered: opposed piston and loop scavenged engines.

Laws concerning emissions from heavy duty (HD) internal combustion engines are becoming increasingly stringent. New engine technologies are needed to satisfy these new requirements and to reduce fossil fuel dependency. One way to achieve both objectives can be to partially replace fossil fuels with alternatives that are sustainable with respect to emissions of greenhouse gases, particulates and nitrogen oxides (NOx). A suitable candidate is methanol. The aim of the study presented here was to investigate the possible advantages of combusting methanol in a heavy duty Diesel engine. Those are, among others, lower particulate emissions and thereby bypassing the NOx-soot trade-off. Because of methanol’s poor auto-ignition properties, Diesel was used as an igniting sources and both fuels were separately direct injected. Therefore, two separate standard common rail Diesel injection systems were used together with a newly designed cylinder head and adapted injection nozzles.

Reducing emissions and improving efficiency are major goals of modern internal combustion engine research. The use of biomass-derived fuels in Diesel engines is an effective way of reducing well-to-wheels (WTW) greenhouse gas (GHG) emissions. Moreover, partially premixed combustion (PPC) makes it possible to achieve very efficient combustion with low emissions of soot and NOx. The objective of this study was to investigate the effect of using alcohol/Diesel blends or neat alcohols on emissions and thermal efficiency during PPC. Four alcohols were evaluated: n-butanol, isobutanol, n-octanol, and 2-ethylhexanol. The alcohols were blended with fossil Diesel fuel to produce mixtures with low cetane numbers (26-36) suitable for PPC. The blends were then tested in a single cylinder light duty (LD) engine. To optimize combustion, the exhaust gas recirculation (EGR) level, lambda, and injection strategy were tuned.

Laws concerning to emissions from heavy duty (HD) internal combustion engines are becoming increasingly stringent. New engine technologies are therefore needed to satisfy these new legal requirements and reduce fossil fuel dependency. One way to achieve both objectives is to partially replace fossil fuels with alternatives that are more sustainable with respect to emissions of greenhouse gas, particulates and NOx. As a first step towards the development of a direct injected dual fuel engine using diesel fuel and renewable alcohols such as methanol or ethanol, we have studied ethanol (E100) sprays generated with a standard high pressure diesel fuel injection system in a high pressure/temperature spray chamber with optical access. The experiments were performed at a gas density of ∼27kg/m3 at ∼550 °C and ∼60 bar, representing typical operating conditions for a HD engine at low loads.

The paper presents a numerical investigation, aimed to explore the potential of 2-stroke Diesel engines, able to meet Euro VI requirements, for application to medium size commercial vehicles (power rate: 80 kW at 2600 rpm, max. torque 420 Nm from 1200 to 1400 rpm). The study is based on experimental performance of a highly developed 4-stroke engine. Two different designs are considered: Loop and Uniflow scavenging, the latter obtained through an opposed piston configuration. In both cases, no poppet valves are used, and the lubrication is provided by a 4-stroke-like oil sump. The study started with the development of a 4-stroke EURO VI engine, on the basis of a previous EURO IV version. A prototype of the new engine (named 430) was built and tested.

The paper reviews the design of the supercharging system for a strongly downsized engine, to be installed on a sport car. Design is supported by cfd-1d engine simulations, using an experimentally calibrated model. The goal of the supercharging system is to deliver the required values of boost pressure at steady operating conditions, and to maintain or improve the full size engine response during acceleration (one of the most critical issues for downsized engines). Two options have been considered: 1) two-stage turbocharging, with two small turbochargers as a high-pressure stage, and one big turbo as low pressure stage (referred to as “TRITURBO”; 2) two-stage supercharging made up of one low pressure stage turbocharger and one electric supercharger (referred to as “E-SUPER”).

Passive selective catalyst reduction (SCR) systems can be used as aftertreatment systems for lean burn spark ignition (SI)-engines. Their operation is based on the interaction between the engine, an ammonia formation catalyst (AFC), and an SCR catalyst. Under rich conditions the AFC forms ammonia, which is stored in the SCR catalyst. Under lean conditions, the SCR catalyst reduces the engine out NOx using the stored NH3. This study compared the ammonia production and response times of a standard three way catalyst (TWC) and a Pd/Al2O3 catalyst under realistic engine operating conditions. In addition, the relationships between selected engine operating parameters and ammonia formation over a TWC were investigated, considering the influence of both the chosen load point and the engine settings.

Interest in 2-stroke engines has been recently renewed by several prototypes, developed for the automotive and/or the aircraft field. Loop scavenging, with piston controlled ports is particularly attractive, but the configurations successfully developed in the past for motorbike racing (in particular, the 125cc unit displacement, crankcase pump engines), are not suitable for automotive applications. Therefore, new criteria are necessary to address the scavenging system design of the new generation of 2-stroke automobile/aircraft engines. The paper reviews the transfer ports optimization of a loop scavenged 2-stroke cylinder, whose main parameters were defined in a previous study. The optimization has been carried by means of a parametric grid, considering 3 parameters (2 tilt angles, and the focus distance), and 3 different engine speeds (2000-3000-4000 rpm, assuming a Diesel engine). A set of scavenging CFD-3d simulations have been performed by using a customized version of KIVA-3V.

Two-stroke diesel engines could be a promising solution for reducing carbon dioxide (CO2) emissions from light-duty vehicles. The main objective of this study was to assess the potential of two-stroke engines in achieving a substantial reduction in CO2 emissions compared to four-stroke diesel baselines. As part of this study 1-D models were developed for loop scavenged two-stroke and opposed piston two-stroke diesel engine concepts. Based on the engine models and an in-house vehicle model, projections were made for the CO2 emissions for a representative light-duty vehicle over the New European Driving Cycle and the Worldwide Harmonized Light Vehicles Test Procedure. The loop scavenged two-stroke engine had about 5-6% lower CO2 emissions over the two driving cycles compared to a state of the art four-stroke diesel engine, while the opposed piston diesel engine had about 13-15% potential benefit.