Search Results

The paper describes the setup of a 4-cylinder 1.4-liter prototype Spark Ignited (SI)-engine, which is highly boosted, extremely downsized and port fuel injected. During experimental data gathering with the engine it was discovered that the originally mounted fuel injectors were non-optimized an unable to produce an expected low fuel consumption performance at low speed, low load engine working conditions. To solve this problem by finding an optimized alternative solution for the mixture preparation process it was decided to use a high-performance numerical simulation tool. The paper presents the overall layout of the prototype engine as well as the structure of the 3-D dynamic optimization tool used to address the mixture preparation problem. The paper continues with a detailed description of the different steps used to reach the complete optimization of the mixture preparation system (both the fuel injectors and the intake manifold).

The paper presents the background research on the physics of the droplet coalescence phenomena carried out by an interactive usage of high-level 3-D numerical simulation tools and high-level optical visualization and measurement techniques. The presentation continues with the description of a new injector atomizer plate layout, which enables a physical coalescence control of the droplet population within the entire fuel spray. Finally are presented examples of the impact on exhaust emissions of the introduction the new atomizer plate with coalescence control by engine test bed experiments (steady state low load conditions) and vehicle tests (first cold part of the FTP-cycle).

The paper presents the main reasons for the increasing market share of vehicles with the capacity to run on random bio fuel blends. It explains the reason for which a single fuel supply system is mandatory in modern flex vehicles, even for cold start by pure ethanol fuelling The paper continues with an analytic research for the most appropriate device location and a detailed description of 3 suggested device layouts. The paper concludes by a presentation of a series of data obtained by real-time vehicle experiments at low ambient temperature conditions.

The present paper describes a study, which can enable a small displacement (1.3 liter) turbocharged European CR-diesel engine to tolerate an important increase in EGR-level. The analysis is performed by use of a 3D virtual numerical engine model, which isolates the main parameters that must be optimized within the perimeter of the combustion chamber. The paper gives a short introduction to the physical background for NOx and soot-formation as well as a recall of the main issues related to the simulation models used in the virtual engine simulation. The analysis is performed in a 9 points load/speed test matrix. Several EGR-rates are studied as well as the impact of a precise temperature control of the exhaust gas re-introduced in the intake manifold. The paper concludes by an analysis of the cumulated impact on the EGR-level tolerated by the engine after the introduction of the suggested optimization measures.

The present paper describes a study of the basic parameters, which govern particulate (soot) formation within the combustion chamber of a small displacement (1.3 liter) turbocharged European CR-diesel engine. The main tools used for the study are a real fired engine, a numerical virtual engine and a special high ambient pressure vessel for injector spray visualization. The paper describes an improved soot formation model implemented in the virtual engine setup. A comparison is presented between measured and computed combustion data at 8 different load points. The paper concludes with a discussion of the means, which can be used to minimize the particulate matter formation in the design phase of both the combustion layout and the fuel injector atomizer as well as in the design of the injection control strategies.

The first part of the present paper describes the means by which the spray momentum can be decreased. The objective can be obtained either by injector-internal geometrical design changes, which very often lead to a highly non-uniform spray density/droplet distribution or by a new injector-external process, called the colliding jet (CJ) approach. The paper continues with a detailed description of the physics of the controlled secondary breakup process provided by the CJ-approach, which enables a very uniform density/droplet distribution on the downstream side of the collision zone as well as an approximately 40 % decrease in spray penetration depth. The knowledge of the physics of the CJ-approach enables the introduction of a new spray model in the 3-D numerical simulation code NCF-3D.

The main objective of the paper is to describe the optimization work performed to adjust direct injection (DI)-technology to SI-engines running at high (8000 to 10000 rpm.) and extremely high speeds (more than 18000 rpm). In the first category are located a certain number of small and middle displacement two-stroke series produced engines. In the second category are the typical high power racing engines used for competitions like the formula 1. The first part of the paper describes the particular requirements that an in-cylinder fuelling and mixture preparation will have to fulfill with the extremely short period available for introduction and vaporization of the fuel. The paper continues with a description of the different spray shapes, spray penetration velocities and atomization capabilities, which are optimal for the different combustion chamber architectures.

In the future generation of low consumption SI-engine layouts, it has become necessary to reduce costs as well as the complexity level and, increase the system reliability by the latter. To avoid driving the GDI-system in the critical, very lean stratified operation mode without losing the fuel consumption benefit, a solution is suggested, which combines a fully variable valve control system with a low level, robust GDI combustion layout. The first part of the present paper presents the latest development in the field of high precision multi-hole GDI injector spray nozzles. The basic aspects of mixture preparation with multi-hole gasoline atomizers are highlighted and their spray behavior compared to that of the current swirl atomizer nozzle. The second part of the paper presents primary optimization of a largely homogeneous GDI combustion layout combined with a fully variable valve timing control system including complete cylinder de-activation.

Experimental measurements and numerical computations were made to characterize a spray generated by a high-pressure swirl injector. The Phase Doppler technique was applied to get information on droplet sizes (d10) and axial velocities at defined distances from the injector tip. Global spray visualization was also made. Computations were carried out using a modified version of KIVA 3V. In particular, the break-up length of the sheet and its dimension were computed from a semi-empirical correlation related to the wave instability theory suggested by Dombrowski, including the modifications introduced by Han and Reitz. Two different approaches were used to describe the initial spray conditions. According to the first, discrete particles with a characteristic size equal to the thickness of the sheet are injected. The second approach assumes, that the particles having a SMD computed by a semi-empirical correlation are injected according to a statistical distribution.

The new European legislation on two-wheeler pollutant emissions has forced two stroke engine manufacturers to study the direct fuel injection (DI) technology. The Piaggio “ET2 Injection” was the first DI engine in production, using the FAST system (Fully Atomized Stratified Turbulence) applied on a 50 cm3 engine. Within the framework of the DOLCE project (Development Of innovative Low pollutant, noise and fuel Consumption two stroke spark ignition Engines for future vehicles for individual urban mobility) coordinated by Piaggio and supported by the European Commission, a 125 cm3 direct injection 2-stroke engine was developed. This paper presents the engine-related part of this work, which was concluded in March 2000. The engine is equipped with the FAST system and the fuel metering is performed by means of a low-pressure electronic fuel injection system integrated in an Engine Management System (EMS) specially developed for this type of application.

The first part of the paper gives an overview of the environmental conditions with which a future two stroke engine must comply. The reasons for which a direct gasoline injection into the combustion chamber offers one of the most promising solutions are explained. In order to understand the potential of different GDI-layouts to produce very lean stratified combustion behavior two different approaches are studied in detail. The latest version of the fuel/air mixture injection used by the F. A. S. T. engine is confronted with a basically liquid high-pressure layout, similar to the design used in automotive four-stroke passenger car engines. A description is given of the basic fluid dynamics of the 50 cc engine used for the study as well as of the experimental and numerical tools applied. The paper concludes with a detailed presentation of the obtained results as well as of the arguments retained to produce the final rating.

The first part of the paper gives an overview of the current results obtained with the first-generation of GDI-powered vehicles launched on the European market. In view of the rather limited success in fuel consumption gain the second-generation of very lean stratified layouts has begun, but this process requires the development and application of new high-level analysis tools. A possible high performance approach is the multi-purpose use of 3-D numerical simulation both in the development and the engine control strategy calibration phases. The development of a small 1.6 liter lean stratified engine project was chosen to demonstrate the dual application capability of the NCF-3D simulation tool. The paper continues with a description of the engine application frame, the basic features of the NCF-3D simulation tool and the latest enhancements made to combustion and fuel composition models within the software frame.

The first part of the paper gives an overview of the current status in fuel consumption gain of the GDI-vehicles previously launched on the European market. In order to increase the potential for a further gain in specific fuel consumption the behaviour of 3 different combustion chamber layouts are studied. The chamber layouts are aimed to adapt as well as possible to the particular requirements for application to a small displacement/small bore engine working in stratified lean conditions. The paper continues with a description of the application that shows the different steps of a structured optimisation methodology for a 1.2 litre, small bore 4-cylinder engine. The applications of an air-motion-guided and a wall-guided layout with a mechanically actuated valve train to the same combustion chamber are discussed. The potential of the air-motion-guided concept is enhanced through the introduction of an electromagnetic fully variable valve train.

The first part of the paper gives an overview of the environmental conditions with which a future two stroke powered vehicle must comply and explains the reasons for which a direct gasoline injection into the combustion chamber offers a potential solution. The paper continues with a description of the fuel/air mixture injection used in the F.A.S.T. concept and gives a detailed overview of the layout of the 125 cc engine to which it is applied. The structure of its electronic engine management system, mandatory for the necessary control precision, is presented. Hereafter is made a short introduction to the visualization and numerical computation tools used for the engine design optimization. The paper concludes with a detailed presentation and discussion of the experimental results obtained with the engine operated, either in steady state and transient conditions on an engine test rig, and mounted in a classic small dimension two-wheel vehicle submitted to road tests.

The first part of the paper gives an overview of the current development status of the GDI system layout for the middle displacement engine, typically 2 liter, using the stoichiometric or weak lean concept. Hereafter are discussed the particular requirements for the transition to a small displacement/small bore engine working in stratified lean conditions. The paper continues with a description of the application of the different steps of the optimization methodology for a 1.2 liter, small bore 4 cylinder engine from its original base line MPI version towards the lean stratified operation mode. The latest changes in the combustion model, used in the numerical simulation software applied to the combustion chamber design, are discussed and comparison made with the previous model. The redesign of the combustion chamber geometry, the proper choice of injector atomizer type and location and the use of two-stage injection and multi-spark strategies are discussed in detail.

The suggestions for upcoming Euro 2000 clean air act puts an increasing legislative pressure for lower specific fuel consumption in order to reduce the emission of CO2 and thereby decrease the impact of the “green house” effect. One of the possible suggestions to meet these requirements for SI-engines is the gasoline direct injected (GDI) power unit. One of the key points of the success of a layout of a GDI system is the optimization of the fuel injector and combustion chamber charge formation parameters. A brief description of the basic GDI-system used during the study is given. Hereafter are outlined the computational and experimental optimization tools which have been used to produce, on a reasonable industrial time scale, the main indications to optimize the design of a given injector/chamber configuration. The paper discusses in detail the results produced by the latest enhancements introduced into the 3D multi-phase computational approach, NCF-3D.

The first part of the paper outlines the main potential advantages of the direct fuel injection concept and describes the overall layout of a system in which the keystones are a piston rotary fuel delivery pump with integrated pressure regulation and electromechanical fast responding fuel injectors. Three different nozzle designs are discussed, a divergent pintle solid cone, a pintle hollow cone swirl layout and a closed cap multijet design. In the second part of the paper the used experimental high pressure dynamic test equipment is discussed. Then the results obtained by the use of phase illuminated visualisation techniques and phase Doppler analysis as well as by a 3D CFD approach are presented. The paper concludes by relating the spray patterns and the associated droplet penetration velocities, produced by the different nozzle types, to the combustion chamber layout and to the possible manufacturing precision requirements for each nozzle type.

The paper describes the application of laser sheet flow visualisation with numerical image analysis as a useful complementary tool to numerical simulation techniques for the optimisation of fluid dynamics within SI-engine in-take systems. The lay-out of the laser sheet visualisation system and the applied numerical image analysis are discussed in detail. Two applicative examples are given, one of smoke induced visualisation of the internal gas flow of an intake manifold, the other of natural visualisation of fuel injector wall film deposit in the intake runner. Finally is concluded that the addition of visualisation techniques to the development strategy allows a time gain, because it contributes to a rapid understanding of complex flow phenomena.

In order to improve the atomization capability of a standard port fuel injector, an optimized suggestion for an air shrouded injector is presented. The fluid dynamic part of the retained solution is composed of a special flat seat design for the fuel metering function combined with a post atomization adapter enabling both mono- and multi-spray modes. The concept works equally well in natural manifold gradient mode and with an external pressure pump. The realized concept is tested in both free jet experiments and on two different 2 litre engines, one operated in stoechiometric conditions the other in lean-burn conditions. The experimental work confirms a potential of the concept to increase torque stability and thereby lean-burn limits, decrease required spark advance and enable open inlet valve injection and consequently decrease wall wetting phenomena.