Refine Your Search

Date

Date

Topic

Topic

Parts Copper alloys Truck and Bus Powertrain Committee Fuels and Energy Sources Metals Electrical, Electronics, and Avionics

Search Results

Viewing 1 to 20 of 65
123Next >Last >>
Sort by published
Standard

Recommended Practice for Measuring Fuel Economy and Emissions of Hybrid-Electric and Conventional Heavy-Duty Vehicles
2020-05-15
CURRENT
J2711_202005
This SAE Recommended Practice was established to provide an accurate, uniform, and reproducible procedure for simulating use of MD/HD conventional vehicles (CVs) and hybrid-electric vehicles (HEVs), as well as plug-in hybrid-electric vehicles (PHEVs) and battery electric vehicles (BEVs) on powertrain dynamometers for the purpose of measuring emissions and fuel economy. This document does not specify which emissions constituents to measure (e.g., HC, CO, NOx, PM, CO2), as that decision will depend on the objectives of the tester. While the main focus of this procedure is for calculating fuel and energy consumption, it is anticipated that emissions may also be recorded during execution of this procedure. It should be noted that most MD/HD powertrains addressed in this document would be powered by engines that are certified separately for emissions. The engine certification procedure appears in the Code of Federal Regulations, Title 40 §86 and §1065.
Standard

Recommended Practice for Measuring Fuel Economy and Emissions of Hybrid-Electric and Conventional Heavy-Duty Vehicles
2018-07-23
HISTORICAL
J2711_201807
This SAE Recommended Practice was established to provide an accurate, uniform and reproducible procedure for simulating use of heavy-duty hybrid-electric vehicles (HEVs) and conventional vehicles on dynamometers for the purpose of measuring emissions and fuel economy. Although the recommended practice can be applied using any driving cycle, the practice recommends three cycles: the Manhattan cycle, representing low-speed transit bus operation; the Orange County Transit Cycle, representing intermediate-speed bus operation; and the Urban Dynamometer Driving Schedule (UDDS) cycle representing high-speed operation for buses and tractor-trailers. This document does not specify which emissions constituents to measure (e.g., HC, CO, NOx, PM, CO2), as that decision will depend on the objectives of the tester.
Standard

Snap-Acceleration Smoke Test Procedure for Heavy-Duty Diesel Powered Vehicles
2018-02-15
CURRENT
J1667_201802
This SAE Recommended Practice applies to vehicle exhaust smoke measurements made using the Snap-Acceleration test procedure. Because this is a non-moving vehicle test, this test can be conducted along the roadside, in a truck depot, a vehicle repair facility, or other test facilities. The test is intended to be used on heavy-duty trucks and buses powered by diesel engines. It is designed to be used in conjunction with smokemeters using the light extinction principle of smoke measurement. This procedure describes how the snap-acceleration test is to be performed. It also gives specifications for the smokemeter and other test instrumentation and describes the algorithm for the measurement and quantification of the exhaust smoke produced during the test. Included are discussions of factors which influence snap-acceleration test results and methods to correct for these conditions.
Standard

Recommended Practices for CNG Powered Medium and Heavy-Duty Trucks
2018-02-12
CURRENT
J2406_201802
This SAE Recommended Practice provides guidance for the construction, operation, and maintenance of CNG powered medium and heavy-duty trucks. The intent of this document is to cover TRUCKS (6350 kg (14 001 gvw pounds) and above) and specifically excludes passenger vehicles such as: buses, recreational vehicles, motor homes and/or passenger vehicles which may incorporate a truck chassis in their construction.
Standard

Liquefied Natural Gas (LNG) Vehicle Fuel
2018-02-12
CURRENT
J2699_201802
This SAE Information Report applies to liquefied natural gas used as vehicle fuel and requires LNG producers to provide the required information on the fuel composition and its “dispense by” date.
Standard

Rating of Winches
2017-11-03
CURRENT
J706_201711
This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.
Standard

Torque Ratings for Power Take-off Mounting Pads
2017-09-19
CURRENT
J2662_201709
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

Recommended Remanufacturing Procedures for Manual Transmission Clutch Assemblies
2017-08-22
CURRENT
J1915_201708
This SAE Recommended Practice is prepared as a guideline to improve and maintain the quality of remanufactured automotive products. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though they may not fully be equivalent to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing, so as to provide durable operation of the part as well as acceptable performance when installed in a vehicle. The remanufacturer should also carefully consider the safety aspects of the product and any recommendations of the original manufacturer related to remanufacturing or rebuilding their product.
Standard

Manual Transmission Shift Patterns
2017-08-15
CURRENT
J1608_201708
Provide standard shift pattern guidelines for manual transmission shift controls in light, medium, and heavy trucks and buses.
Standard

Pilot Bearings for Truck and Bus Applications
2017-08-14
CURRENT
J1731_201708
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
Standard

Hydraulic Hybrid Terminology and Definitions
2012-11-21
CURRENT
J2898_201211
As the number of Hydraulic Hybrid Powertrain equipped motor vehicles has increased, the number of terms, abbreviations, and acronyms which describe various components of these systems has increased. For the sake of industry standardization and to bring some order to the proliferation of such terms, abbreviations, and acronyms, the SAE Truck and Bus Hydraulic Hybrid committee prepared this document.
Standard

Manual Transmission Efficiency and Parasitic Loss Measurement
2012-11-09
CURRENT
J1540_201211
Because of the intense focus on fuel economy and fuel emission standards, it has become imperative to optimize vehicle drivetrains. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies a test procedure which maps torque transmittal efficiency and parasitic losses for manual transmissions. The application of this document is intended for manual transmissions used in light (class 4) through heavy truck applications with both simple and compound ratio structures. This document is separated into two parts. The first compares input and output torque throughout a specified input speed range in order to determine the overall transmission efficiency. This test is used to evaluate all forward gears; testing in reverse is optional.
Standard

Manual Transmission Shift Patterns
2012-11-09
HISTORICAL
J1608_201211
Provide standard shift pattern guidelines for manual transmission shift controls in light, medium, and heavy trucks and buses.
123Next >Last >>
X