Search Results

Abstract In this article, the effects of mixture dilution using EGR or excessive air on adiabatic flame temperature, laminar flame speed, and minimum ignition energy are studied to illustrate the fundamental benefits of lean combustion. An ignition system developing a new active pre-chamber (APC) design was assessed, aimed at improving the indicated thermal efficiency (ITE) of a 1.5 L four-cylinder gasoline direct injection (GDI) engine. The engine combustion process was simulated with the SAGE detailed chemistry model within the CONVERGE CFD tool, assuming the primary reference fuel (PRF) to be a volumetric mixture of 93% iso-octane and 7% n-heptane. The effects of design parameters, such as APC volume, nozzle diameter, and nozzle orientations, on ITE were studied. It was found that the ignition jet velocity from the pre-chamber to the main chamber had a significant impact on the boundary heat losses and combustion phasing.

Abstract The water droplet erosion (WDE) on high-speed rotating wheels appears in several engineering fields such as wind turbines, stationary steam turbines, fuel cell turbines, and turbochargers. The main reasons for this phenomenon are the high relative velocity difference between the colliding particles and the rotor, as well as the presence of inadequate material structure and surface parameters. One of the latest challenges in this area is the compressor wheels used in turbochargers, which has a speed up to 300,000 rpm and have typically been made of aluminum alloy for decades, to achieve the lowest possible rotor inertia. However, while in the past this component was only encountered with filtered air, nowadays, due to developments in compliance with tightening emission standards, various fluids also collide with the spinning blades, which can cause mechanical damage.

Abstract The two-branch exhaust of an asymmetric twin-scroll turbocharged engine are asymmetrically and periodically complicated, which has great impact on turbine matching. In this article, a matching effect of turbine speed parameter on asymmetric twin-scroll turbines based on the exhaust pulse energy weight distribution of a heavy-duty diesel engine was introduced. First, it was built as an asymmetric twin-scroll turbine matching based on exhaust pulse energy distribution. Then, by comparing the average matching point and energy matching points on the corresponding turbine performance map, it is revealed that the turbine speed parameter of energy matching points was a significant deviation from the turbine speed parameter under peak efficiency, which leads to the actual turbine operating efficiency lower than the optimal state.

Abstract The ground vibration test (GVT) is an important phase in a new aircraft development program, or the structural modification of a certified aircraft, to experimentally determine the structural vibrational modes of the aircraft and their modal parameters. These modal parameters are used to validate and correlate the dynamic finite element model of the aircraft to predict potential structural instabilities (such as flutter), assessing the significance of modifications to research vehicles by comparing the modal data before and after the modification and helping to resolve in-flight anomalies. Due to the high cost and the extensive preparations of such tests, a new method of vibration testing called the taxi vibration test (TVT) rooted in operational modal analysis (OMA) was recently proposed and investigated as an alternative method to conventional GVT.

Abstract The notable increase in combustion noise in the 7–10 kHz band has become an issue in the development of pre-chamber jet ignition combustion gasoline engines that aim for enhanced thermal efficiency. Combustion noise in such a high-frequency band is often an issue in diesel engine development and is known to be due to resonance in the combustion chamber. However, there are few cases of it becoming a serious issue in gasoline engines, and effective countermeasures have not been established. The authors therefore decided to elucidate the mechanism of high-frequency combustion noise generation specific to this engine, and to investigate effective countermeasures. As the first step, in order to analyze the combustion chamber resonance modes of this engine in detail, calculation analysis using a finite element model and experimental modal analysis using an acoustic excitation speaker were conducted.

Abstract Improving thermal efficiency of an internal combustion engine is one of the most cost-effective ways to reduce life cycle-based CO2 emissions for transportation. Lean burn technology has the potential to reach high thermal efficiency if simultaneous low NOx, HC, and CO emissions can be achieved. Low NOx can be realized by ultra-lean (λ ≥ 2) spark-ignited combustion; however, the HC and CO emissions can increase due to slow flame propagation and high combustion variability. In this work, we introduce a new combustion concept called turbulent jet-controlled compression ignition, which utilizes multiple turbulent jets to ignite the mixture and subsequently triggers end gas autoignition. As a result, the ultra-lean combustion is further improved with reduced late-cycle combustion duration and enhanced HC and CO oxidation. A low-cost passive prechamber is innovatively fueled using a DI injector in the main combustion chamber through spray-guided stratification.

Abstract The broadband aeroacoustics of a side mirror is investigated with a stochastic noise source method and compared to scale-resolving simulations. The setup based on an already existing work includes two geometrical variants with a plain series side mirror and a modified mirror with a forward-facing step mounted on the inner side. The aeroacoustic near- and farfield is computed by a hydrodynamic–acoustic splitting approach by means of a perturbed convective wave equation. Aeroacoustic source terms are computed by the Fast Random Particle-Mesh method, a stochastic noise source method modeling velocity fluctuations in time domain based on time-averaged turbulence statistics. Three RANS models are used to provide input data for the Fast Random Particle-Mesh method with fundamental differences in local flow phenomena.

Abstract Neutron diffraction is a powerful tool for noninvasive and nondestructive characterization of materials and can be applied even in large devices such as internal combustion engines thanks to neutrons’ exceptional ability to penetrate many materials. While proof-of-concept experiments have shown the ability to measure spatially and temporally resolved lattice strains in a small aluminum engine on a timescale of minutes over a limited spatial region, extending this capability to timescales on the order of a crank angle degree over the full volume of the combustion chamber requires careful design and optimization of the engine structure to minimize attenuation of the incident and diffracted neutrons to maximize count rates.

Abstract Limited fossil fuel resources and carbonaceous greenhouse gas emissions are two major problems the world faces today. Alternative fuels can effectively power internal combustion engines to address these issues. Methanol can be an alternative to conventional fuels, particularly to displace gasoline in spark ignition engines. The physicochemical properties of methanol are significantly different than baseline gasoline and fuel mixture-aim lambda; hence methanol-fueled engines require modifications in the fuel injection parameters. This study optimized the fuel injection quantity, spark timing, and air–fuel ratio for M85 (85% v/v methanol + 15% v/v gasoline) fueling of a port fuel-injected single-cylinder 500 cc motorcycle test engine. Comparative engine performance, combustion, and emissions analyses were performed for M85 and baseline gasoline.

Abstract Methanol is emerging as an alternate internal combustion engine fuel. It is getting attention in countries such as China and India as an emerging transport fuel. Using methanol in spark ignition engines is easier and more economical than in compression ignition engines via the blending approach. M85 (85% v/v methanol and 15% v/v gasoline) is one of the preferred blends with the highest methanol concentration. However, its physicochemical properties significantly differ from gasoline, leading to challenges in operating existing vehicles. This experimental study addresses the challenges such as cold-start operation and poor throttle response of M85-fueled motorcycle using a port fuel injection engine. In this study, M85-fueled motorcycle prototype is developed with superior performance, similar/better drivability, and lower emissions than a gasoline-fueled port-fuel-injected motorcycle.

Abstract Turbocharged spark-ignition (SI) engines, owing to frequent engine knocking events, utilize retarded spark timing that causes combustion inefficiency, and high turbine inlet temperature (Trb-In T) levels. Fuel enrichment is implemented at high power levels to prevent excessive Trb-In T levels, resulting in an additional fueling penalty and higher CO emissions. In current times, fuel-enrichment reductions are of high strategic importance for engine manufacturers to meet the imminent emissions regulations. To that end, the authors investigated the divided exhaust period (DEP) concept in a 2.2 L turbocharged SI engine with a geometric compression ratio of 14 by decoupling blowdown (BD) and scavenge (SC) events during the exhaust process. Using a validated 1D engine model, the authors first analyzed the DEP concept in terms of pumping mean effective pressure (PMEP) and engine knocking (KI) reduction.

Abstract Tank-to-wheels (TTW) CO2 reduction for ethanol blends is determined from either gasoline composition or vehicle exhaust measurements. Fuels are characterized using a carbon intensity (CI), which is the ratio of carbon (as CO2 mass) in the fuel to the net heating value. Our objective is to assess changes in CI of market gasoline with varying ethanol content that can be used to appreciate change in vehicle tailpipe greenhouse gases (GHG) in response to policy controlling the ethanol level in market fuels. Ethanol has both a reduced carbon content and a reduced net (lower) heating value relative to petroleum species, with a CI slightly lower than that of typical petroleum gasoline. However, ethanol blending offers additional CI reduction because it enables a reduction of aromatics in the petroleum blendstock for oxygenate blending (BOB) while maintaining octane rating of the blend. Aromatics have a CI about 20% higher than paraffins.

Abstract In recent years, the number of electric vehicles (EVs) has grown rapidly, as well as public interest in them. However, the lack of sufficient range is one of the most common complaints about these vehicles, which is particularly problematic for people with long daily commutes. Thus, this article proposed a solution to this problem by installing micro wind turbines (MWTs) on EVs as a range extender. The turbines will generate electricity by converting the kinetic energy of the air flowing through the MWT into mechanical energy, which can have a reasonable effect on the vehicle aerodynamics. The article uses mathematical modelling and numerical analysis. Regarding the modelling, a detailed EV model in MATLAB/SIMULINK was developed to analyze the EV performance using various driving cycles in real time.

Abstract Research into efficient internal combustion (IC) engines need to continue as the majority of vehicles will still be powered by IC or hybrid powertrains in the foreseeable future. Recently, lean-burn gasoline compression ignition (GCI) with high-pressure direct injection has been receiving considerable attention among the research community due to its ability to improve thermal efficiency and reduce emissions. To maximize GCI benefits in engine efficiency and emissions tradeoff, co-optimization of the combustion system and fuel formation is required. Thus, it is essential to study the spray characteristics of different fuels under engine-like operating conditions. In this work, high-pressure spray characteristics are experimentally studied for three blends of gasoline, namely, Naphtha, E30, and research octane number (RON) 98. A single-hole custom-built injector was used to inject fuel into a constant volume chamber with injection pressure varying from 40 MPa to 100 MPa.

Abstract Since the steady-state computational fluid dynamics (CFD) Reynolds-averaged Navier–Stokes (RANS) turbulence models offer low-cost and sensible accuracy, they are frequently utilized for bluff bodies’ external aerodynamics investigations (e.g., upwind, crosswind, and shape optimization). However, no firm certainty is made regarding the best model in terms of accuracy and cost. Based on cost and accuracy aspects, four RANS turbulence models were studied, which are Spalart–Allmaras, realizable k-ε, RNG k-ε, and SST k-ω. Ahmed body with a 25° slant angle benchmark case was introduced for this investigation. Two grids were generated to satisfy the near-wall treatment of each turbulence model. All grid settings were proposed and discussed in detail. Fluid-structure analysis was performed on five different planes.

Abstract Pre-chamber jet ignition technologies have been garnering significant interest in the internal combustion engine field, given their potential to deliver shorter burn durations, increased combustion stability, and improved dilution tolerance. However, a clear understanding of the relationship between pre-chamber geometry, operating condition, jet formation, and engine performance in light-duty gasoline injection engines remains under-explored. Moreover, research specifically focusing on high dilution levels and passive pre-chambers with optical accessibility is notably scarce. This study serves to bridge these knowledge gaps by examining the influence of passive pre-chamber nozzle diameter and dilution level on jet formation and engine performance.

Abstract The use of data-driven algorithms for the integration or substitution of current production sensors is becoming a consolidated trend in research and development in the automotive field. Due to the large number of variables and scenarios to consider; however, it is of paramount importance to define a consistent methodology accounting for uncertainty evaluations and preprocessing steps, that are often overlooked in naïve implementations. Among the potential applications, the use of virtual sensors for the analysis of solid emissions in transient cycles is particularly appealing for industrial applications, considering the new legislations scenario and the fact that, to our best knowledge, no robust models have been previously developed.

Abstract Pre-chamber turbulent jet ignition (TJI) is a method of generating distributed ignition sites through multiple high-speed turbulent jets in order to achieve an enhanced burn rate in the engine cylinder when compared to conventional spark plug ignition. To study the gas-dynamic interactions between the two chambers in a gasoline engine, a three-dimensional numerical model was developed using the commercial CFD code CONVERGE. The geometry and parameters of the engine used were based on a modified turbocharged GM four-cylinder 2.0 L GDI gasoline engine. Pre-chambers with nozzle diameters of 0.75 mm and 1.5 mm were used to investigate the effect of pre-chamber geometry on pre-chamber charging, combustion, and jet formation. The local developments of gas temperature and velocity were captured by adaptive mesh refinement, while the turbulence was resolved with the k-epsilon model of the Reynolds averaged Navier–Stokes (RANS) equations.

Abstract Biodiesel is a suitable alternative to diesel because of its carbon neutrality, renewability, lubricity, and lower pollutant emissions. However, extensive research indicates higher oxides of nitrogen (NOx) emissions with biodiesel. A practical method to combat this problem is utilizing water and biodiesel as emulsions. The effect of biodiesel-water emulsion in high-pressure fuel injection systems is not fully explored in the existing literature. The present study addresses this research gap by utilizing biodiesel-water emulsions in a modified light-duty diesel engine. The governor-controlled injection system was adapted to a fully flexible electronic system capable of high-pressure injection. Unlike other literature studies, the fuel injection timings were optimized with biodiesel-water emulsions to maximize brake thermal efficiency (bte) at every load condition.

Abstract Quantifying exhaust gas composition and temperature in vehicles with internal combustion engines (ICEs) is crucial to understanding and reducing emissions during transient engine operation. This is particularly important before the catalytic converter system lights off (i.e., during cold start). Most commercially available gas analyzers and temperature sensors are far too slow to measure these quantities on the timescale of individual cylinder-firing events, thus faster sensors are needed. A two-color mid-infrared (MIR) laser absorption spectroscopy (LAS) sensor for gas temperature and carbon monoxide (CO) mole fraction was developed and applied to address this technology gap. Two quantum cascade lasers (QCLs) were fiber coupled into one single-mode fiber to facilitate optical access in the test vehicle exhaust. The QCLs were time-multiplexed in order to scan across two CO absorption transitions near 2013 and 2060 cm–1 at 15 kHz.