Search Results

Abstract AISI H13 hot work tool steel is commonly used for applications such as hot forging and hot extrusion in mechanical working operations that face thermal and mechanical stress fluctuations, leading to premature failures. Cryogenic treatment was applied for AISI H13 steel to improve the surface hardness and thereby fatigue resistance. This work involves failure analysis of H13 steel specimens subjected to cryogenic treatment and gas nitriding. The specimens were heated to 1020°C, oil quenched followed by double tempering at 550°C for 2 h, and subsequently, deep cryogenically treated at −185°C in the cryochamber. Gas nitriding was carried out for 24 h at 500°C for 200 μm case depth in NH3 surroundings. The specimens were subjected to rotating bending fatigue at constant amplitude loading at room temperature.

Abstract Super duplex stainless steel (SDSS) is a type of stainless steel made of chromium (Cr), nickel (Ni), and iron (Fe). In the present work, a 1.6 mm wide thin sheet of SDSS is joined using gas tungsten arc welding (GTAW). The ideal parameter for a bead-on-plate trial is found, and 0.216 kJ/mm of heat input is used for welding. As an outcome of the welding heating cycle and subsequent cooling, a microstructural study revealed coarse microstructure in the heat-affected zone and weld zone. The corrosion rate for welded joints is 9.3% higher than the base metal rate. Following the corrosion test, scanning electron microscope (SEM) analysis revealed that the welded joint’s oxide development generated a larger corrosive attack on the weld surface than the base metal surface. The percentages of chromium (12.5%) and molybdenum (24%) in the welded joints are less than those in the base metal of SDSS, as per energy dispersive X-ray (EDX) analysis.

Abstract NVH refinement of commercial vehicles is the key attribute for customer acceptance. Engine and road irregularities are the two major factors responsible for the same. During powertrain isolators’ design alone, the mass and inertia of the powertrain are usually considered, but in practical scenarios, a directly coupled subsystem also disturbs the boundary conditions for design. Due to the upgradation in emission norms, the exhaust aftertreatment system of modern automotive vehicles becomes heavier and more complex. This system is further coupled to the powertrain through a flexible joint or fixed joint, which results in the disturbance of the performance of the isolators. Therefore, to address this, the isolators design study is done by considering a multi-body dynamics model of vehicles with 16 DOF and 22 DOF problems, which is capable to simulate static and dynamic real-life events of vehicles.

Abstract TOC

Abstract Despite the growing prominence of electrified vehicles, internal combustion engines remain essential in future transportation. This study delves into passive pre-chamber jet ignition, a leading-edge combustion technology, offering a comprehensive visualization of its operation under varying load and dilution conditions in light-duty GDI engines. Our primary objectives are to gain fundamental insights into passive pre-chamber jet ignition and subsequent main combustion processes and evaluate their response to different load and dilution conditions. We conducted experimental investigations using a light-duty, optical, single-cylinder engine equipped with three passive pre-chamber designs featuring varying nozzle diameters. Optical diagnostic imaging and heat release analysis provided critical insights.

Abstract TOC

Abstract This study investigated the influence of high-strength low-alloy steel on the fatigue life of a load-bearing member with a non-load-bearing transverse welded attachment (T-joint). It compared high cycle fatigue data to two fatigue design codes, namely BS 7608 and Eurocode EN 1993-1-9. Different base and filler material combinations of varying material strengths were investigated, resulting in a total of three different specimen configurations. Two material combinations had a high-strength steel (Strenx® 700 MC D) for the base material, with one combination having a matched filler material and the other having an undermatched filler material. The third material combination had a lower-strength steel (S 355 JR AR) for the base material, with a matched filler material. Tensile tests were performed to confirm the base material mechanical properties and weld quality of the manufactured specimens.

Abstract Recent legislations require very low soot emissions downstream of the particulate filter in diesel vehicles. It will be difficult to meet the new more stringent OBD requirements with standard diagnostic methods based on differential sensors. The use of inexpensive and reliable soot sensors has become the focus of several academic and industrial works over the past decade. In this context, several diagnostic strategies have been developed to detect DPF malfunction based on the soot sensor loading time. This work proposes an advanced online diagnostic method based on soot sensor signal projection. The proposed method is model-free and exclusively uses soot sensor signal without the need for subsystem models or to estimate engine-out soot emissions. It provides a comprehensive and efficient filter monitoring scheme with light calibration efforts.

Abstract Methanol is emerging as an alternate internal combustion engine fuel. It is getting attention in countries such as China and India as an emerging transport fuel. Using methanol in spark ignition engines is easier and more economical than in compression ignition engines via the blending approach. M85 (85% v/v methanol and 15% v/v gasoline) is one of the preferred blends with the highest methanol concentration. However, its physicochemical properties significantly differ from gasoline, leading to challenges in operating existing vehicles. This experimental study addresses the challenges such as cold-start operation and poor throttle response of M85-fueled motorcycle using a port fuel injection engine. In this study, M85-fueled motorcycle prototype is developed with superior performance, similar/better drivability, and lower emissions than a gasoline-fueled port-fuel-injected motorcycle.

Abstract In this article, the effect of heat treatment on the microstructure and mechanical behavior of medium-carbon steel wire intended for the spring mattress is investigated using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), X-ray diffraction, Vickers hardness (Hv), and tensile strength. The results indicate that the microstructure elongation along the wire axis is observed with the bending and kinking lamellae at the deformation level of 57.81%, this change appears as a fracture in the microstructure and leads to an increase in hardness, tensile strength, and intensities of diffraction patterns. After heat treatment, we observed a redistribution in the grain, which is almost the same in the wire rod and drawn wires; indeed, this led to a decrease in hardness, tensile strength, and augmentation in intensities of peaks. The EBSD pole figures reveal the development of texture in the cementite slip plane (001).

Abstract Pre-chamber jet ignition technologies have been garnering significant interest in the internal combustion engine field, given their potential to deliver shorter burn durations, increased combustion stability, and improved dilution tolerance. However, a clear understanding of the relationship between pre-chamber geometry, operating condition, jet formation, and engine performance in light-duty gasoline injection engines remains under-explored. Moreover, research specifically focusing on high dilution levels and passive pre-chambers with optical accessibility is notably scarce. This study serves to bridge these knowledge gaps by examining the influence of passive pre-chamber nozzle diameter and dilution level on jet formation and engine performance.

Abstract Quantifying exhaust gas composition and temperature in vehicles with internal combustion engines (ICEs) is crucial to understanding and reducing emissions during transient engine operation. This is particularly important before the catalytic converter system lights off (i.e., during cold start). Most commercially available gas analyzers and temperature sensors are far too slow to measure these quantities on the timescale of individual cylinder-firing events, thus faster sensors are needed. A two-color mid-infrared (MIR) laser absorption spectroscopy (LAS) sensor for gas temperature and carbon monoxide (CO) mole fraction was developed and applied to address this technology gap. Two quantum cascade lasers (QCLs) were fiber coupled into one single-mode fiber to facilitate optical access in the test vehicle exhaust. The QCLs were time-multiplexed in order to scan across two CO absorption transitions near 2013 and 2060 cm–1 at 15 kHz.

Abstract The shot-to-shot variations in common rail injection systems are primarily caused by pressure wave oscillations in the rail, pipes, and injector body. These oscillations are influenced by fuel physical properties, injector needle movement, and pressure and suction control valve activations. The pressure waves are generated by pump actuation and injector needle movement, and their frequency and amplitude are determined by fluid properties and flow path geometry. These variations can result in cycle-to-cycle engine fluctuations. In multi-injection and split-injection strategies, the pressure oscillation from the first shot can impact the hydraulic characteristics of subsequent shots, resulting in variations in injection rate and amount. This is particularly significant when using alternative fuels such as biodiesel, which aim to reduce emissions while maintaining fuel atomization quality.

Abstract A rapid compression and expansion machine (RCEM) was used to experimentally investigate the ignition phenomena of dielectric-barrier discharge (DBD) in engine conditions. The effect of elevated pressure and temperature on ignition phenomena of a methane/air premixed mixture was investigated using a DBD igniter. The equivalence ratio was changed to elucidate the impact of DBD on flame kernel development. High-speed imaging of natural light and OH* chemiluminescence enabled visualization of discharges and flame kernel. According to experimental findings, the discharges become concentrated and the intensity increases as the pressure and temperature rise. Under different equivalence ratios, the spark ignition (SI) system has a shorter flame development time (FDT) as compared with the DBD ignition system.

Abstract Lubricant additives are the main means to improve the performance of lubricants. In this article, green and inexpensive layered kaolin were selected as lubricant additives, and the effects of the type of modifier, concentration, particle size of kaolin additives, and working temperatures on the tribological performance of lubricants were investigated. The results showed that the Span80 modifier can effectively improve the dispersibility and friction reduction effects of kaolin oil samples. Compared with kaolin oil samples without the modifier, the modified kaolin oil can reduce the friction coefficient by 40.9% and the wear spot diameter of the steel balls by 43.8%. The layered kaolin additive can significantly reduce the friction coefficient and wear of steel balls in lubrication, and the friction coefficient showed a trend of decreasing and then increasing with increasing kaolin additive concentration and particle size.

Abstract The exhaust manifold of a high-performance motorcycle engine is subjected to combined thermal and vibrational loadings. In this research, the whole fatigue assessment of an exhaust manifold is addressed. First, a classic low-cycle fatigue analysis is performed. Then, a specific methodology for determining the fatigue cycle of components subjected to thermal and vibration loadings is developed and presented in a way that possible damages can be evaluated. The results are post-processed and the damage caused by fatigue cycles is computed referring to the Wöhler curve of the material using the Dirlik approach.

Abstract Prediction of the surface finish of hardened bearing steels was estimated in machining with ceramic uncoated cutting tools under various process parameters using two statistical approaches. A second-order (quadratic) regression model (MQR, multiple quantile regression) for the surface finish was developed and then compared with the artificial neural network (ANN) method based on the coefficient determination (R 2), root mean square error (RMSE), and percentage error (PE). The experimental results exhibited that cutting speed was the dominant parameter, but feed rate and depth of cut were insignificant in terms of the Pareto chart and analysis of variance (ANOVA). The optimum surface finish in machining bearing steel was achieved at 100 m/min speed, 0.1 mm/revolution (rev) feed rate, and 0.6 mm depth of cut.

Abstract The present investigation has been conducted to study the tribological and adhesion properties of X10CrNi18-8 austenitic stainless steel (ASTM 301) coatings deposited on aluminum alloys such as AU4G by using the arc-spraying process. These coatings were made with and without a bond-coat layer, which is constituted by NiAl. The structure of the phases that are present in coatings was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The measurements of microhardness and tribological behavior at different loads were also performed on the surface of the coatings. Adherence test was also carried out using four-point bending tests. The SEM showed that the dense microstructures of coatings have a homogeneous lamellar morphology with the presence of porosities and unmelted particles. The main phase of coating corresponds to a solid solution as a face-centered cubic (fcc).

Abstract With the introduction of advanced lightweight materials with complex microstructures and behaviors, more focus is put on the accurate determination of their forming limits, and that can only be possible through experiments as the conventional theoretical models for the forming limit curve (FLC) prediction fail to perform. Despite that, CAE engineers, designers, and toolmakers still rely heavily on theoretical models due to the steep costs associated with formability testing, including mechanical setup, a large number of tests, and the cost of a stereo digital image correlation (DIC) system. The international standard ISO 12004-2:2021 recommends using a stereo DIC system for formability testing since two-dimensional (2D) DIC systems are considered incapable of producing reliable strains due to errors associated with out-of-plane motion and deformation.

Abstract To understand how the composition of novel lubricant additives and their ash interact with gasoline particulate filters (GPFs), an accelerated aging protocol was conducted using three lubricant additive formulations and two GPF types. The additive packages (adpaks) consisted of Ca+Mg detergent in a 3:1 or 0:1 ratio and an anti-wear component—either zinc dialkyl dithiophosphate (ZDDP) or a novel phosphonium-phosphinate ionic liquid (IL) substitute. The particulate sampling captured amount/compositions of particulate matter (PM) generated, total particulate number, and size distribution. Five ash loadings were completed. GPF position and adpak composition affected the backpressure, ash composition, ash morphology, and captured mass. The particulate sampling indicated that the ash component consisted primarily of particles less than 50 nm in size and that the Mg-only adpak resulted in more particulate of 50–400 nm in size.