Search Results

The modern solution of two-stage combustion, namely the Turbulent Jet Ignition, enables the combustion of ultra-lean mixtures. Thanks to this solution, it became possible to reduce fuel consumption and, at the same time, to increase the combustion process indicators (including the overall combustion system efficiency). The article presents the results of numerical tests of a heavy-duty engine equipped with the TJI system running on hydrogen fuel. The operating conditions of the Heavy-Duty engine at n = 1500 rpm and IMEP = 10 bar with a prechamber with 7 holes were analyzed. The research was conducted with the use of lean mixtures (global lambda ca. 2 or more). The AVL FIRE software was used to perform the analysis of different fuel doses delivered to the main chamber, with a constant global excess air coefficient value. Increasing the proportion of hydrogen in the pre-chamber resulted in its reduction in the main chamber.

This paper discusses the legislative situation regarding type approval of plug-in hybrid vehicles (also known as off-vehicle charging hybrid-electric vehicles, OVC-HEV) in the range of exhaust emissions and fuel consumption. A range of tests were conducted on two Euro 6d-complaint OVC-HEVs to quantify emissions. Procedures were based on EU legislative requirements. For laboratory (chassis dyno) testing, two different test cycles and three different ambient temperatures were used for testing. Furthermore, in some cases additional measurements were performed, including measurement of emissions of particulate matter and continuous analysis of regulated and unregulated pollutants in undiluted exhaust. Consumption of electrical energy was also monitored. On-road testing was conducted on the test vehicle tested on the chassis dyno in the tests mentioned above, as well as on a second OVC-HEV test vehicle.

The article is an investigation into the exhaust emission impact of operating a shunting locomotive SM42 and a track diagnostics machine UPS-80-001. The comparison of the two vehicles makes it possible to estimate the overall environmental costs of two different types of rail vehicles operating at their typical work parameters. This was done using selected exhaust emission indicators. It is used to indicate the need for further improvement in vehicle ecology such as hybrid or electric systems. Other solutions are investigated as forms of mitigating the ecological impact of operating such vehicles in or near human population centers.

Non-plugin hybrids represent a technology with the capability to significantly reduce fuel consumption (FC), without any changes to refuelling infrastructure. The EU market share for this vehicle type in the passenger car segment was 3% in 2018 and this powertrain type remains of interest as an option to meet the European Union (EU) fleet average CO2 limits. EU legislative procedures require emissions limits to be met during the chassis dynamometer test and in the on-road real driving emissions (RDE) test, while official CO2/FC figures are quantified via the laboratory chassis dynamometer test only. This study employed both legislative test procedures and compared the results. Laboratory (chassis) dynamometer testing was conducted using the Worldwide Harmonised Light Vehicles Test Procedure (WLTP). On-road testing was carried out in accordance with RDE requirements, measuring the concentration of regulated gaseous emissions and the number of solid particles (PN).

Non-Road machines constitutes a large group of machines designed for various tasks and mainly using CI engines for propulsion. This category includes vehicles with drive systems of a maximum capacity of several kilowatts as well as with drives with a capacity of up to thousands of kilowatts depending on the purpose of the machine. Within this group, mobile machines referred to as NRMM (Non-Road Mobile Machinery) stand out. Numerous studies of scientific institutions in Europe and around the world have proven the differences between the exhaust emissions tested in type approval tests and the actual emissions in this group of vehicles. They result from differences in operating points (crankshaft speed and load) of engines during their operation. A big problem is also their considerable age and degree of wear. Approval standards themselves are less stringent than those of heavy-duty vehicles (HDVs), although the engines have similar design and performance.

In this study, two vehicles were tested under real driving conditions with gaseous exhaust emissions measured using a portable emissions measurement system (PEMS). One of the vehicles featured a hybrid powertrain with a spark ignition internal combustion engine, while the other vehicle featured a non-hybrid (conventional) spark ignition internal combustion engine. Aside from differences in the powertrain, the two test vehicles were of very similar size, weight and aerodynamic profile, meaning that the power demand for a given driving trace was very similar for both vehicles. The test route covered urban conditions (but did include driving on a road with speed limit 90 km/h). The approximate test route distance was 12 km and the average speed was very close to 40 km/h.

The paper presents results of the road tests of exhaust gas emissions of vehicles of different emission classes (Euro 4 and Euro 5, with different mileage), fuelled with compressed natural gas. The tests of exhaust emissions were conducted on parts of the road with different characteristics of the traffic intensity. For each phase of the tests, the characteristics of the test run and the value of exhaust gas emissions were determined. To measure the exhaust emission the Portable Emission Measurement System (PEMS) was used.

The paper presents an analysis of the emission level from a heavy-duty truck of the GVW of 12,000 kg. The exhaust emission tests were performed under actual traffic conditions in the area of Poznań. For the tests portable exhaust emission analyzers SEMTECH DS and AVL Micro Soot Sensor were used. The characteristics of the exhaust emission components have been determined in relation to the engine speed and load as well as vehicle parameters (speed and acceleration). The paper includes an analysis of the engine operating conditions as well as the range of engine speeds and engine loads. The vehicle fuel consumption was also determined through the carbon balance method. Based on the obtained values of the emission of CO, NOx and PM, the emission indexes were determined that provided information on the relation of the measured emissions to the levels specified in the EEV standard. The emissions of all the exhaust components, except NOx were lower than the EEV limits.

The paper presents a new method for assessment of combustion process correctness taking place in CI engines, based on the expanded vibroacoustic signal analysis. The method uses chosen non-linear, spectrum and time-frequency analyses of the signal. Diagnostics of the correctness of the above main engine process and misfire detection for engines at exploitation conditions with the use of the various methods of the accompanying processes analysis was the aim of the presented analyses. Possibility of the method application to combustion process assessment of the CI engines was verified, algorithms of misfire detection for the each method are described, quantity point estimators of processes and conditions of the OBD diagnostics realization were obtained, methodology of the measurement process, limits of the methods use and their diagnostic accuracy in the point of view of the combustion OBD III engine monitor design are also presented.

The paper presents the results of tests on a combustion engine of an armored modular vehicle 8x8 Rosomak under combat simulating conditions. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of toxic compounds at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption were performed under the conditions of combat simulation and in the overboost mode. Based on the obtained results, an analysis of the engine and vehicle operation was performed and the on-road and unit exhaust emissions as well as on-road and unit fuel consumption were compared.

The paper presents the results of the investigations of an armored modular vehicle 8x8 Rosomak fitted with a diesel engine during start and warm-up. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of exhaust emission at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption have also been carried out under static conditions, during startup and at constant engine speed without engine load. For the measurement of the engine operating conditions and the fuel consumption a diagnostic vehicle system was used.

The investigations into the emissions from light-duty vehicles are carried out on a chassis dynamometer in the NEDC test in Europe and FTP75 test in the US. Such tests do not entirely reflect the real road conditions. It should be noted that the changes in the methodology of emissions testing should go in the direction where they get closer to the actual road conditions. The paper presents the road test results obtained in an urban congested areas. The analysis of the road tests results (exhaust emissions and fuel consumption) was carried out considering the road conditions (vehicle speed and acceleration). The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. For these measurements a portable SEMTECH DS analyzer by SENSORS, Particle Counter by AVL and Particle Seizer EEPS by TSI has been used.

In order to measure the concentration of exhaust emissions a mobile emission testing analyzer SEMTECH DS by SENSORS Inc was used. In the study the results of the vehicle emission tests in the road conditions were presented, as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle in motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of the emission intensity.

The investigations into the emissions from light-duty vehicles have been carried out on a chassis dynamometer (NEDC test in Europe and FTP75 test in the US). Such tests do not entirely reflect the real road conditions and that is why we should analyze the correlation of the laboratory versus on-road test results. The paper presents the on-road test results obtained in an urban and extra urban cycles. For these measurements a portable SEMTECH DS analyzer by SENSORS has been used. The device is an analyzer enabling an on-line measurement of the emission gases concentration in a real driving cycle under real road conditions. The road tests were performed on road portions of several kilometers each. The obtained results were compared with the results obtained for the same vehicle during the NEDC test on a chassis dynamometer. The comparative analysis was performed including the urban and extra-urban cycles.

Research on the influence of oxygenated diesel fuels on the PM/NOx emission trade-off was carried out with use of 11 different synthetic oxygenated compounds, representing 3 chemical groups (glycol ethers, maleates, carbonates). Each of oxygenates were evaluated as a fuel additive at a concentration of 5% v/v in the same base diesel fuel. The tests were conducted on a passenger car equipped with a common rail turbocharged diesel engine over the European cycle NEDC and US FTP-75 cycle. All the tested oxygenates caused a reduction in PM emissions and most of them caused a certain increase in NOx emissions. The changes in emissions depended on the oxygenate type and cycle. In general, the favorable and unfavorable influence of oxygenated compounds was more intensive during the NEDC, which is a softer and less transient cycle than the FTP-75. The most favorable changes in the PM/NOx emission trade-off were obtained for maleates and carbonates.

The paper presents a new method of misfire identification for a Diesel engine, based on results of parameterizations of a time-frequency a(t, f) map of an engine vibration signal. The Joint Time-Frequency Analysis (JTFA) methods have been proposed as a tool for a time-frequency selection of a vibration signal. An algorithm of the method has been outlined and an example application of a synchronous averaged Short Time Fourier Transform (STFT) for extracting vibration signal components related to combustion process has been shown. Parameterization of a(t, f) map gives measures covariable with misfire in a cylinder of an internal combustion engine. The method and analyses of the chosen characteristics and parameters were used in on-line diagnostics of the combustion process lack, what gave the necessary bases for application of the new method in OBD system.

In order to measure the concentration of toxic compounds a mobile analyzer for toxic tests SEMTECH DS by SENSORS Inc. was used. In the study the results of the vehicle emission tests in the road conditions were presented as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the harmful compound emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of emission intensity.

The paper presents the test results of the influence of maleate oxygenated additives to diesel fuel on exhaust emissions. Following the previous tests of glycol ethers (SAE Paper 2007-01-0069), the authors decided to use maleates as oxygenates to obtain greater changes in PM/NOx trade-off than the changes obtained as a result of the use of glycol ethers. It was found that in the NEDC maleates at the same concentration as in the case of glycol ethers ensure more favourable changes of PM/NOx trade-off and, as a matter of fact, caused greater reduction in PM emissions without the growth of NOx emissions, however, at the cost of CO and HC emissions. The tests performed in the FTP-75 confirmed a significantly weaker influence of maleates, both positive (PM) and negative (CO, HC) than in the NEDC. They did not find in both cycles any influence of maleates at the tested concentration upon fuel consumption and CO2 emissions.

The paper describes the research on the problem of oxygenating diesel fuel with the use of gases containing oxygen (air or diesel exhaust gas). The incentive, which encouraged the authors to exploit this idea, was a number of promising results of some earlier research on oxygenated fuel additives. The paper provides a detailed description of the system, especially the injection pump for dissolving gas in the fuel, designed and built by the authors. The paper describes also some changes in physical and chemical parameters of the fuel, which were observed while the fuel was flowing through the experimental injection system. These changes resulted from the reactions between fuel and oxygen, which were additionally reinforced by high pressure and temperature in the experimental injection system. In the further part of the article, the attention is drawn to the way the gases containing oxygen influence the exhaust emissions.

In the year 2005, the EURO IV fuel specification came into effect and the requirements for diesel fuel properties have become even more stringent. In this way, the potential of diesel fuel for emissions reduction has already been to a large extent exploited and the most emissions-sensitive fuel parameters can now be changed in a narrow range only. The shortfall in NOx and PM emissions control in diesel engines is, however, so great that more drastic fuel changes will be needed. One of the most promising fuel modifications for exhaust emissions control seems to be oxygenated additives. The objective of the study described in this paper was to analyze under transient conditions the influence of synthetic oxygenated fuel additives on exhaust emissions. The tests were conducted on a Euro IV passenger car. Six oxygenated additives were tested over the New European Driving Cycle (NEDC).