Search Results

This specification covers an aluminum alloy in the form of plate 4.001 to 10.000 inches (101.60 to 254.00 mm), inclusive, in nominal thickness.

The devices of this SAE Standard provide the means by which passenger compartment dimensions can be obtained using a deflected seat rather than a free seat contour as a reference for defining seating space. All definitions and dimensions used in conjunction with this document are described in SAE J1100. These devices are intended only to apply to the driver side or center occupant seating spaces and are not to be construed as instruments which measure or indicate occupant capabilities or comfort. This document covers only one H-point machine installed on a seat during each test. Certified H point templates and machines can be purchased from:SAE International400 Commonwealth DriveWarrendale, PA 15096-0001Specific procedures are included in Appendix A for seat measurements in short- and long-coupled vehicles and in Appendix B for measurement of the driver seat cushion angle. Specifications and a calibration inspection procedure for the H point machine are given in Appendix C.

The documents listed in this ballot are being proposed for reaffirmation

This specification covers procedures for ultrasonic immersion inspection of premium-grade wrought titanium and titanium alloy round billet 5 inches (127 mm) and over in nominal diameter (see 2.6.1). Metal alloy billets other than titanium may be tested to this specification with the use of suitable reference standards.

This specification covers procedures for identifying carbon and low-alloy steels, corrosion- and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy sheet, strip, and plate, and aircraft tubing.

This specification covers a magnesium alloy in the form of welding wire (see 8.5).

This specification covers an aluminum alloy in the form of plate 4.000 to 10.000 inches (101.6 to 254.0 mm), inclusive, in nominal thickness (see 8.5).

This specification covers a precipitation hardenable corrosion- and heat-resistant nickel alloy in the form of seamless tubing.

This specification covers a corrosion- and heat-resistant nickel alloy in the form of welding wire.

The test method describes the procedure for the direct determination of water concentration in polyol ester and diester based aerospace lubricants by commercially available automated coulometric Karl Fischer titration instruments. The method was validated to cover the water concentration range of 150 to 3500 µg/g. The method may also be suitable for the determination of water concentrations outside this range and for other classes of fluids; however, the precision statement shall not be applicable for such uses.

This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate 0.005 to 1.000 inches (0.13 to 25.40 mm) in nominal thickness in the solution heat-treated condition.

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 5.000 inches (127.00 mm), inclusive, in nominal diameter or least thickness (see 8.5).

This standard covers the requirements for non-separable, airframe anti-friction needle bearings, corrosion resistant and traditional materials, intended for use in flight vehicle control systems, with radial loads.

This SAE Aerospace Standard (AS) defines the nomenclature for surface finishes commonly used for sheet and strip in aerospace material specifications. It is applicable to steel and to iron, nickel, cobalt, and titanium base alloys.

This specification establishes the requirements for a hard anodic coating on aluminum and aluminum alloys.

The following document were been proposed by the sponsor or by committee E for Reaffirmation at the Spring meeting 2024.

The document describes typical processes with examples on how to manage reliability assessment hardware and software used on structural health monitoring systems, and for structure health management solutions. It addresses reliability assessment guidelines from design phase, manufacturing, assemblies, installation, considering installation and environmental conditions. Link between Quality system and reliability assessment is developed

This document will provide topics and possible content for industry to use in setting up training programs for personnel involved in deployment of SHM systems. The two primary parts of the training are: installation and usage.

This specification covers a precipitation hardenable, corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD and 0.015 inch (0.38 mm) and over in nominal wall thickness.

This document covers the recommended practice for determining the acceptability of the dendrite arm spacing (DAS) of D357-T6 aluminum alloy castings required to have tensile strength not lower than 50 ksi (345 MPa).