Search Results

Scope unavailable.

Scope unavailable.

No scope is available.

This is for testing purposes

ARP4754B Clarification Notice to address typographical errors and clarify portions of the document to facilitate usage of the newly released ARP4754B.

This specification covers a trimethylol propane triheptanoate fluid (see 8.2) representative of standard type (SPC) gas turbine engine oils.

The document describes typical processes with examples on how to manage reliability assessment hardware and software used on structural health monitoring systems, and for structure health management solutions. It addresses reliability assessment guidelines from design phase, manufacturing, assemblies, installation, considering installation and environmental conditions. Link between Quality system and reliability assessment is developed

This document will provide topics and possible content for industry to use in setting up training programs for personnel involved in deployment of SHM systems. The two primary parts of the training are: installation and usage.

Update of when to implement a specific strain rate into tensile testing.

This specification covers a precipitation hardenable, corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD and 0.015 inch (0.38 mm) and over in nominal wall thickness.

This document covers the recommended practice for determining the acceptability of the dendrite arm spacing (DAS) of D357-T6 aluminum alloy castings required to have tensile strength not lower than 50 ksi (345 MPa).

This document covers all metal, self-locking wrenching nuts, plate nuts, shank nuts, and gang channel nuts made from a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286 and of 160 ksi tensile strength at room temperature, with maximum test temperature of parts at 1200 °F.

This procurement specification covers aircraft quality self-locking nuts for wrenching (hex, spline) and anchor (plate, gang channel, shank) types of nuts made from a corrosion and heat-resistant nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. Tension height nuts having overall length of threaded portion not less than 1.2 times the nominal thread diameter have 1210 MPa minimum tensile strength at room temperature. Shear height nuts having shorter threaded portion have 1100 MPa minimum tensile strength at room temperature. Maximum test temperature of parts is 730 °C.

This SAE Standard describes the methods for testing flexible harness coverings for use on ground vehicle electrical distribution systems, specifically protection from severe mechanical impact. This SAE Standard shall apply to all tapes, extruded tubes, and textile sleeves used for this purpose.

This SAE Standard is equivalent to ISO 362-1:2015 and specifies an engineering method for measuring the noise emitted by road vehicles of categories M and N under typical urban traffic conditions. It excludes vehicles of category L1, L2, L3, L4, and L5.The specifications are intended to reproduce the level of noise generated by the principal noise sources during normal driving in urban traffic. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle.The test method requires an acoustical environment that is obtained only in an extensive open space. Such conditions are usually provided for during:Measurements of vehicles for regulatory certification and/or type approval.Measurements at the manufacturing stage.Measurements at official testing stations.

This specification covers a magnesium alloy in the form of sheet and plate from 0.016 to 3.000 inches (0.41 to 76.20 mm), inclusive, in thickness (see 8.5).

This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles up to 40 square inches (258 cm2) in cross-sectional area (solids) and up to 8.5 inches (216 mm) OD by 1.188 inches (30.18 mm) wall thickness (tubing) (see 8.5).

This specification establishes the requirements for flake or granular cetyl alcohol, solvents for dissolving the cetyl alcohol, preparation and application requirements for use of cetyl alcohol as an installation lubricant on mechanical fasteners, such as pins, bolts, nuts, washers, threaded or nonthreaded fastening devices, and inspection criteria for coated parts.

This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.

This specification covers unalloyed copper in the form of sheet, strip, and plate at least 0.015 inch (0.38 mm) in nominal thickness.