Search Results

This SAE Recommended Practice provides procedures and methods for testing service, spring applied parking, and combination brake actuators with respect to durability, function, and environmental performance. A minimum of six test units designated A, B, C, D, E, and F are to be used to perform all tests per 1.1 and 1.2.

This Recommended Practice is derived from OEM and tier-1 laboratory tests and applies to two-axle multipurpose passenger vehicles, or trucks with a GVWR above 4536 kg (10 000 pounds) equipped with hydraulic disc or drum service brakes. Before conducting testing for a specific brake sizes or under specific test conditions, review, agree upon, and document with the test requestor any deviations from the test procedure. Also, the applicable criteria for the final test results and wear rates deemed as significantly different require definition, assessment, and proper documentation; especially as this will determine whether or not Method B testing is needed. This Recommended Practice does not evaluate or quantify other brake system characteristics such as performance, noise, judder, ABS performance, or braking under extreme temperatures or speeds. Minimum performance requirements are not part of this recommended practice.

This procurement specification covers the requirements for metal tube support clamps comprising of two spring clips made of corrosion and heat resistant steel and the associated PTFE single split cushion that supports the tube. See Figure 1.

This SAE Recommended Practice establishes methods to determine grade parking performance with respect to:a. Ability of the parking brake system to lock the braked wheels.b. The trailer holding or sliding on the grade, fully loaded, or unloaded.c. Applied manual effort.d. Unburnished or burnished brake lining friction conditions.e. Down and upgrade directions.

This SAE Aerospace Standard (AS) sets forth criteria for the selection and verification processes to be followed in providing tires that will be suitable for intended use on civil aircraft. This document encompasses new and requalified radial and bias aircraft tires.

This document describes a recommended test procedure to assess the burst characteristics of tires used on 14CFR Part 25 or similar transport airplanes.

An investigation into the current range of tire chine designs approved for application on aircraft requiring non-standard water spray deflection.

This SAE Aerospace Standard (AS)/Minimum Operational Performance Specification (MOPS) specifies the minimum performance requirements of Remote On-Ground Ice Detection Systems (ROGIDS). These systems are ground-based. They provide information that indicates whether frozen contamination is present on aircraft surfaces. Section 1 provides information required to understand the need for the ROGIDS, ROGIDS characteristics, and tests that are defined in subsequent sections. It describes typical ROGIDS applications and operational objectives and is the basis for the performance criteria stated in Section 3 through Section 5. Section 2 provides reference information, including related documents, abbreviations, and definitions. Section 3 contains general design requirements for the ROGIDS. Section 4 contains the Minimum Operational Performance Requirements for the ROGIDS, which define performance in icing conditions likely to be encountered during ground operations.

This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR.

This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

This Recommended Practice provides a common method to measure wear of friction materials (brake pad assemblies and brake shoes) and their mating parts (brake disc or brake drum). These wear measurements apply to brakes fitted on passenger cars and light trucks up to 4536 kg of Gross Vehicle Weight Rating under the Federal Motor Vehicle Safety Standard (FMVSS), or vehicles category M1 (passenger cars up to nine occupants, including the driver) under the European Community’s ECE Regulations.

This procedure is applicable to modes from 500 and 13,000 Hz. The parameters measured with this procedure are defined as the damping factor, ξ for first nine vibration modes of the beam. The measurement will be done in free-free conditions and with temperature.

This specification covers a corrosion- and heat-resistant steel in the form of welding wire.

This specification covers tubular-shaped pins, fabricated from carbon steel, having a full-length longitudinal slot to permit flexure when inserted into a hole.

This SAE Aerospace Information Report (AIR) covers forced air technology including: reference material, equipment, safety, operation, and methodology. This resource document is intended to provide information and minimum safety guidelines regarding use of forced air or forced air/fluid equipment to remove frozen contaminants. During the effective period of this document, relevant sections herein should be considered and included in all/any relevant SAE documents.

This specification covers a corrosion- and heat-resistant steel in the form of welding wire.

This specification covers a corrosion- and heat-resistant nickel alloy in the form of welding wire.

This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.

This procurement specification covers tubular-shaped, coiled spring pins made of a corrosion resistant nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.