Search Results

This specification covers procedures for ultrasonic immersion inspection of premium-grade wrought titanium and titanium alloy round billet 5 inches (127 mm) and over in nominal diameter (see 2.6.1). Metal alloy billets other than titanium may be tested to this specification with the use of suitable reference standards.

This specification covers procedures for identifying carbon and low-alloy steels, corrosion- and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy sheet, strip, and plate, and aircraft tubing.

This specification covers a precipitation hardenable corrosion- and heat-resistant nickel alloy in the form of seamless tubing.

The test method describes the procedure for the direct determination of water concentration in polyol ester and diester based aerospace lubricants by commercially available automated coulometric Karl Fischer titration instruments. The method was validated to cover the water concentration range of 150 to 3500 µg/g. The method may also be suitable for the determination of water concentrations outside this range and for other classes of fluids; however, the precision statement shall not be applicable for such uses.

This SAE Aerospace Information Report (AIR) provides information to be considered when performing the safety assessment of electrified propulsion aircraft. Its main focuses are: ● Typical new technologies introduced by electrified propulsion and their impact on safety ● The failure modes of electrified propulsion systems and their components ● Potential effects of failures at system and aircraft levels ● Possible strategies to minimize failures and mitigate their effects The information in this document may be used to generate inputs for system and aircraft safety assessments based on industry standards such as SAE ARP4761. The first issue of this document addresses battery systems, power electronics, eMotors, electrical interconnects and thermal management for fully electric configurations. Future issues are expected to address other subsystems, components and configurations.

To define test cases for the OBD-II interface on external test equipment (such as an OBD-II Scan Tool, Inspection/Maintenance Tester, etc.) which can be used to verify compliance with the applicable standards such as SAE J1978 and SAE J1979 for Passenger Cars, Light-Duty Trucks, and Medium-Duty Vehicles and Engines (OBD II).

This SAE Aerospace Standard (AS) establishes minimum requirements for eddy current inspection of circular holes in nonferrous, metallic, low conductivity (less than 5% IACS) aircraft engine hardware with fasteners removed. The inspection is intended to be performed at maintenance and overhaul facilities on engine run hardware.

This specification covers one type of fluorescent magnetic particles in the form of a mixed, ready-to-use suspension in an odorless, inspection oil vehicle and packaged in aerosol cans.

This is for testing purposes

ARP4754B Clarification Notice to address typographical errors and clarify portions of the document to facilitate usage of the newly released ARP4754B.

The document describes typical processes with examples on how to manage reliability assessment hardware and software used on structural health monitoring systems, and for structure health management solutions. It addresses reliability assessment guidelines from design phase, manufacturing, assemblies, installation, considering installation and environmental conditions. Link between Quality system and reliability assessment is developed

This document will provide topics and possible content for industry to use in setting up training programs for personnel involved in deployment of SHM systems. The two primary parts of the training are: installation and usage.

This specification covers a precipitation hardenable, corrosion- and heat-resistant nickel alloy in the form of seamless tubing 0.125 inch (3.18 mm) and over in nominal OD and 0.015 inch (0.38 mm) and over in nominal wall thickness.

This specification covers aircraft-quality, low-alloy steel in the form of round, seamless tubing.

This document covers all metal, self-locking wrenching nuts, plate nuts, shank nuts, and gang channel nuts made from a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286 and of 160 ksi tensile strength at room temperature, with maximum test temperature of parts at 1200 °F.

This procurement specification covers aircraft quality self-locking nuts for wrenching (hex, spline) and anchor (plate, gang channel, shank) types of nuts made from a corrosion and heat-resistant nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. Tension height nuts having overall length of threaded portion not less than 1.2 times the nominal thread diameter have 1210 MPa minimum tensile strength at room temperature. Shear height nuts having shorter threaded portion have 1100 MPa minimum tensile strength at room temperature. Maximum test temperature of parts is 730 °C.

This specification establishes the requirements for flake or granular cetyl alcohol, solvents for dissolving the cetyl alcohol, preparation and application requirements for use of cetyl alcohol as an installation lubricant on mechanical fasteners, such as pins, bolts, nuts, washers, threaded or nonthreaded fastening devices, and inspection criteria for coated parts.

This SAE Aerospace Standard (AS) establishes the minimum requirements for ground-based aircraft deicing/anti-icing methods and procedures to ensure the safe operation of aircraft during icing conditions on the ground. This document does not specify the requirements for particular aircraft models.NOTE: Refer to particular aircraft operator or aircraft manufacturer’s published manuals and procedures.The application of the procedures specified in this document are intended to effectively remove and/or prevent the accumulation of frost, snow, slush, or ice contamination which can seriously affect the aerodynamic performance and/or the controllability of an aircraft. The principal method of treatment employed is the use of fluids qualified to AMS1424 (Type I fluid) and AMS1428 (Type II, III, and IV fluids).All guidelines referred to herein are applicable only in conjunction with the applicable documents.

This SAE Aerospace Recommended Practice (ARP) outlines the basic general design requirements for ground support equipment used in the civil air transport industry. It is intended to assist in standardizing requirements for various configurations of equipment. For procurement of equipment, sections of this document should be specified with due consideration of the functional and environmental requirements of the equipment, and to the relative cost of satisfying those requirements.

This specification covers a titanium alloy in the form of welding wire (see 8.5).