Search Results

The issue of greenhouse gas (GHG) emissions from the transportation sector is widely acknowledged. Recent years have witnessed a push towards the electrification of cars, with many considering it the optimal solution to address this problem. However, the substantial battery packs utilized in electric vehicles contribute to a considerable embedded ecological footprint. Research has highlighted that, depending on the vehicle's size, tens or even hundreds of thousands of kilometers are required to offset this environmental burden. Human-powered vehicles (HPVs), thanks to their smaller size, are inherently much cleaner means of transportation, yet their limited speed impedes widespread adoption for mid-range and long-range trips, favoring cars, especially in rural areas. This paper addresses the challenge of HPV speed, limited by their low input power and non-optimal distribution of the resistive forces.

Launch vehicles are vulnerable to aeroelastic effects due to their lightweight, flexible, and higher aerodynamic loads. Aeroelasticity research has therefore become an inevitable concern in the development of the Reusable Launch Vehicle (RLV). RLV is the space analogy of an aircraft, a unanimous solution to achieve more affordable access to space. The lightweight control surface of the RLV signifies the relevance of the study on control effectiveness. It is the capability of a control surface such as an elevon or rudder to produce aerodynamic forces and moments to change the launch vehicle's orientation and maneuver it along the intended flight path. The static aeroelastic problem determines the efficiency of control, aircraft trim behaviour, static stability, and maneuvering quality in steady flight conditions. In this study, static aeroelastic analysis was performed on a typical RLV using MSC/NASTRAN inbuilt aerodynamics.

Airframe section of rockets, missiles and launch vehicles are typically cylindrical in shape. The cylindrical shell is subjected to high axial load and an external pressure during its operation. The design of cylinders subjected to such loads is generally found to be critical in buckling. To minimize the weight of cylinders, it is typically stiffened with rings and stringers on the inner diameter to increase the buckling load factor. Conventionally the buckling load estimated by analytical or numerical means is multiplied by an empirical factor generally called Knockdown factor (kdf) to get the critical buckling load. This factor is considered to account for the variation between theory and experiment and is specified by handbooks or codes. In aerospace industry, NASA SP 8007 is commonly followed and it specifies the kdf as a lower bound fit curve for experimental data .

Abstract : In any human space flight program, safety of the crew is of utmost priority. In case of exigency during atmospheric flight, the crew is safely and quickly rescued from the launch vehicle using Crew escape system. Crew escape system is a crucial part of the Human Space flight vehicle which carries the crew module away from the ascending launch vehicle by firing its rocket motors (Pitch Motor (PM), Low altitude Escape Motor (LEM) and High altitude Escape Motor (HEM)). The structural loads experienced by the crew escape system during the mission abort are severe as the propulsive forces, aerodynamic forces and inertial forces on the vehicle are significantly high. Since the mission abort can occur at anytime during the ascent phase of the launch vehicle, trajectory profiles are generated for abort at every one second interval of ascent flight time considering several combinations of dispersions on various propulsive parameters of abort motors and aero parameters.

A structural load estimating methodology was developed for the RLV-TD HEX-01 mission, the maiden winged body technology demonstrator vehicle of ISRO. The technique characterizes atmospheric regime of flight from vehicle loads perspective and ensures adequate structural margin considering atmospheric variations and system level perturbations. Primarily the method evaluates time history of station loads considering effects of vehicle dynamics and structural flexibility. Station loads in the primary structure are determined by superposition of quasi-static aerodynamic loads, dynamic inertia loads, control surface loads and propulsion system loads based on actual physics of the system. Spatial aerodynamic distributions at various Mach numbers along the trajectory have been used in the study. Argumentation in aerodynamic loads due to vehicle flexibility is assessed through the use of spatial aerodynamic distributions.

Severe problem of aerodynamic heating and drag force are inherent with any hypersonic space vehicle like space shuttle, missiles etc. For proper design of vehicle, the drag force measurement become very crucial. Ground based test facilities are employed for these estimates along with any suitable force balance as well as sensors. There are many sensors (Accelerometer, Strain gauge and Piezofilm) reported in the literature that is used for evaluating the actual aerodynamic forces over test model in high speed flow. As per previous study, the piezofilm also become an alternative sensor over the strain gauges due to its simple instrumentation. For current investigation, the piezofilm and strain gauge sensors have mounted on same stress force balance to evaluate the response time as well as accuracy of predicted force at the same instant. However, these force balance need to be calibrated for inverse prediction of the force from recorded responses.

Dimensional optimization has always been a time consuming process, especially for aerodynamic bodies, requiring much tuning of dimensions and testing for each sample. Aerodynamic auxiliaries, especially wings, are design dependent on the primary model attached, as they influence the amount of lift or reduction in drag which is beneficial to the model. In this study CFD analysis is performed to obtain pressure counter of wings. For a wing, the angle of attack is essential in creating proper splits to incoming winds, even under high velocities with larger distances from the separation point. In the case of a group of wings, each wing is then mentioned as a wing element, and each wing is strategically positioned behind the previous wing in terms of its vertical height and its self-angle of attack to create maximum lift. At the same time, its drag remains variable to its shape ultimately maximizing the C L /C D ratio.

The study of aerodynamic forces in hypersonic environments is important to ensure the safety and proper functioning of aerospace vehicles. These forces vary with the angle of attack (AOA) and there exists an optimum angle of attack where the ratio of the lift to drag force is maximum. In this paper, computational analysis has been performed on a blunt cone model to study the aerodynamic characteristics when hypersonic flow is allowed to pass through the model. The flow has a Mach number of 8.44 and the angle of attack is varied from 0º to 20º. The commercial CFD solver ANSYS FLUENT is used for the computational analysis and the mesh is generated using the ICEM CFD module of ANSYS. Air is selected as the working fluid. The simulation is carried out for a time duration of 1.2 ms where it reaches a steady state and the lift and drag forces and coefficients are estimated. The pressure, temperature, and velocity contours at different angles of attack are also observed.

Unmanned Aerial Vehicles (UAVs), or drones, are aerial platforms with diverse applications. Their design is shaped by specific constraints, driving a multidisciplinary, iterative process encompassing aerodynamics, structures, flight mechanics and other domains. This paper describes the design of a fixed-wing UAV tailored to competition requirements. The payload comprises golf balls with specific weight and dimensions. The requirements included maintaining a thrust-to-empty weight ratio below 1 and achieving a high payload fraction, calculated as the ratio of payload weight to total UAV weight. An optimization approach was introduced, altering the conventional UAV sizing process to enhance the payload fraction. This was achieved by adjusting the design points within the solution space derived from constraint analysis.

The present study discusses about the determination of the Seal drag force in the application where elastomeric seal is used with metallic interface in the presence of different fluids. An analytical model was constructed to predict the seal drag force and experimental test was performed to check the fidelity of the analytical model. A Design of Experiment (DoE) was utilized to perform experimental test considering different factors affecting the Seal drag force. Statistical tools such as Test for Equal Variances and One way Analysis of Variance (ANOVA) were used to draw inferences for population based on samples tested in the DoE test. It was observed that Glycol based fluids lead to lubricant wash off resulting into increased seal drag force. Additionally, non-lubricated seals tend to show higher seal drag force as compared to lubricated seals. Keywords: Seal Drag, DoE, ANOVA

Launch vehicle structures in course of its flight will be subjected to dynamic forces over a range of frequencies up to 2000 Hz. These loads can be steady, transient or random in nature. The dynamic excitations like aerodynamic gust, motor oscillations and transients, sudden application of control force are capable of exciting the low frequency structural modes and cause significant responses at the interface of launch vehicle and satellite. The satellite interface responses to these low frequency excitations are estimated through Coupled Load Analysis (CLA). The analysis plays a crucial role in mission as the satellite design loads and Sine vibration test levels are defined based on this. The perquisite of CLA is to predict the responses with considerable accuracy so that the design loads are not exceeded in the flight. CLA validation is possible by simulating the flight experienced responses through the analysis.

It is important to accurately predict the aerodynamic properties for designing applications which involves fluid flows, particularly in the aerospace industry. Traditionally, this is done through complex numerical simulations, which are computationally expensive, resource-intensive and time-consuming, making them less than ideal for iterative design processes and rapid prototyping. Machine learning, powered by vast datasets and advanced algorithms, offers an innovative approach to predict airfoil characteristics with remarkable accuracy, speed, and cost-effectiveness. Machine learning techniques have been applied to fluid dynamics and have shown promising results. In this study, machine learning model called the back-propagation neural network (BPNN) is used to predict key aerodynamic coefficients of lift and drag for airfoils.

This SAE Aerospace Standard (AS)/Minimum Operational Performance Specification (MOPS) specifies the minimum performance requirements of Remote On-Ground Ice Detection Systems (ROGIDS). These systems are ground-based. They provide information that indicates whether frozen contamination is present on aircraft surfaces. Section 1 provides information required to understand the need for the ROGIDS, ROGIDS characteristics, and tests that are defined in subsequent sections. It describes typical ROGIDS applications and operational objectives and is the basis for the performance criteria stated in Section 3 through Section 5. Section 2 provides reference information, including related documents, abbreviations, and definitions. Section 3 contains general design requirements for the ROGIDS. Section 4 contains the Minimum Operational Performance Requirements for the ROGIDS, which define performance in icing conditions likely to be encountered during ground operations.

In order to study the tire friction characteristics under wet skid surface, the “pseudo” hydrodynamic pressure bearing effect is used to be equivalent to the hydrodynamics of water film, and an advanced Lugre tire hydroplaning dynamic model is developed by combining the arbitrary pressure distribution function. The water hydroplaning dynamic tests were carried out for 285/70R19.5 tire under wet of different water film thickness and dry conditions, and the parameters of the advanced Lugre tire dynamic model were identified. The results show that the tire water-skiing model proposed in this paper can effectively simulate the friction characteristics of tires under different water film thicknesses. Under dry conditions, 0.5mm water film and 1mm water film road conditions, the relative errors of the maximum tire friction coefficient between the tested and advanced Lugre tire model are 1.11%, 0.12% and 0.16%, respectively.

This paper delves into the intricate realm of Formula 1 race car aerodynamics, focusing on the pivotal role played by floor flow structures in contemporary racing. The aerodynamic design of the floor of a Formula 1 car is a fundamental component that connects the flow structures from the front wing to the rear end of the car through the diffuser, thus significantly influencing the generation of lift and drag. In this work, CFD was used to predict the structure of the vortices and flow pattern underneath a Formula 1 car using a CAD model that mimicked the modern Red Bull Racing Team’s car in recent years. Through comprehensive analysis and simulation, a detailed understanding of the complex flow patterns and aerodynamic phenomena occurring beneath the floor of the car and its vicinity is presented.

Emission regulations are becoming more stringent, as global temperature continues to rise due to the increasing greenhouse gases in the atmosphere. Battery electric vehicles (BEV), which have zero tailpipe emissions, are expected to become widespread to solve this problem. As the powertrain of BEV is more efficient than conventional powered vehicles, the proportion of energy loss during driving due to aerodynamic drag becomes greater. Therefore, reducing aerodynamic drag for improved energy efficiency is important to extend the pure electric range. At Honda, Computational Fluid Dynamics (CFD) and wind tunnel testing are used to optimize vehicle shape and reduce aerodynamic drag. Highly accurate CFD is essential to efficiently guide the development process towards reducing aerodynamic drag. Specifically, the prediction accuracy for the exterior shape, underfloor devices, tires, and wheels must meet development requirements.

This ARP describes methods that are known to have been used by aircraft manufacturers to evaluate aircraft aerodynamic performance and handling effects following application of aircraft ground deicing/anti-icing fluids (“fluids”), as well as methods under development. Guidance and insight based upon those experiences are provided, including: Similarity analyses. Icing wind tunnel tests. Flight tests. CFD and other numerical analyses. This ARP also describes: The history of evaluation of the aerodynamic effects of fluids. The effects of fluids on aircraft aerodynamics. The testing for aerodynamic acceptability of fluids for SAE and regulatory qualification performed in accordance with AS5900.

This SAE Aerospace Information Report (AIR) covers forced air technology including: reference material, equipment, safety, operation, and methodology. This resource document is intended to provide information and minimum safety guidelines regarding use of forced air or forced air/fluid equipment to remove frozen contaminants. During the effective period of this document, relevant sections herein should be considered and included in all/any relevant SAE documents.