Search Results

A robust process of specifying engine mounting systems for internal combustion engines (ICE) has been established through decades of work and countless applications. Vehicle vibration is a critical consideration in the early stage of vehicle development. Apart from comfort, it also affects the overall vehicle's performance, reliability, Buzz-squeak and rattle (BSR), parts durability and robustness. The most dynamic system in a vehicle is the powertrain, a source of vibration inputs to the vehicle over the frequency range. The mounting system supports a powertrain in a vehicle and isolates the vibration generated from the powertrain to the vehicle. In addition, it also controls the overall dynamic movement of the powertrain system when the vehicle is subjected to road load excitations and avoids contact between the powertrain and other adjacent components of the vehicle.

Key on/off (KOKO) Vibration plays a vital role in the quality of NVH (Noise Vibration and Harshness) on a vehicle. A good KOKO experience on the vehicle is desirable for every customer. The vibration transfer to the vehicle can be refined either by reducing the source vibrations or improving isolation efficiency. For the engine mounting system of passenger cars, the mounts are an isolating element between the powertrain and receiver. Various noise, Vibration, and harshness criteria must be fulfilled by mounting system performance like driver seat rail vibration (DSR), tip-in/tip-out, judder performance, DSR at idle and Key on/off Vibration. Out of these requirements, in the paper, the investigation is done on KOKO improvement without affecting other NVH parameters related to mount performance. Higher damping is required to isolate Vibration generated during the Key-on event, and lower damping is required during the idle condition of the vehicle.

IC (Internal Combustion) engines are evolved and refined over time to greater levels of technology in terms of emission, performance, NVH (Noise, Vibration & Harshness), and design philosophy. Crank-train generates a greater impact on NVH optimization due to its geometry and dynamics. Hence, more attention to mass balancing is required to minimize the negative impact on NVH. The present work demonstrates the evaluation of balancing rate of crank-train system from the first principle of couple balancing. Calculations are conducted at the concept stage to estimate an internal rotating couple balancing of crank-train system due to counterweights and rotating masses. As crankshaft weighs approximately 10-12% weight of an engine and its counter weight plays a vital role in balancing, its optimization will result in a significant impact on NVH.

In comparison to traditional gasoline-powered vehicles, Electric vehicles (EVs) development and adoption is driven by several factors such as zero emissions, higher performance, cost effective in maintenance, smoother and quieter ride. Global OEMs are competing to provide a reduced in-cab noise for ensuring a smooth and quiet driving experience. Short project timelines for EV demands quick design and development. In initial stages of project, input data availability of EV is limited and a simplified approach is necessary to accelerate the development of vehicle. This paper focuses on simulation methodology for predicting structure borne noise from powertrain deploying Transfer Path Analysis approach. Current simulation methodology involves full vehicle model with multiple flexible bodies and full BIW flexible model which leads to complex modelling and longer simulation times.

The goal of reducing fuel consumption and CO2-Emission is leading to turbo-charged combustion engines that deliver high torque at low speeds (down speeding). To meet NVH requirements damper technologies such as DMF (Dual Mass Flywheel) are established, leading to reduced space for the clutch system. Specific measures need to be considered if switching over from SMF (Single Mass Flywheel) to DMF [8]. Doing so has an impact on thermal behavior of the clutch system, for example due to reduced and different distribution of thermal masses and heat transfer to the surroundings. Taking these trends into account, clutch systems within vehicle powertrains are facing challenges to meet requirements e.g. clutch life, cost targets and space limitation. The clutch development process must also ensure delivery of a clutch system that meets requirements taking boundary conditions such as load cycles and driver behavior into account.

The vehicle Heating, Ventilation and Air conditioning (HVAC) system is designed to meet both the safety and thermal comfort requirements of the passengers inside the cabin. The thermal comfort requirement, however, is highly subjective and is usually met objectively by carrying out time dependent mapping of parameters like the velocity and temperature at various in-cabin locations. These target parameters are simulated for the vehicle interior for a case of hot soaking and its subsequent cool-down to test the efficacy of the AC system. Typically, AC performance is judged by air temperature at passenger locations, thermal comfort estimation along with time to reach comfortable condition for human. Simulating long transient vehicle cabin for thermal comfort evaluation is computationally expensive and involves complex cabin material modelling.

Air intake system (AIS) plays a major role in reducing the noise level in passenger car compartment, which has become an important requirement due to increasing customer expectation for better in cab noise. The ideal air intake system design should have minimum possible noise at snorkel entry point which ultimately contributes in cabin noise. There are different techniques that are implemented for an air intake system noise reduction e.g. choosing proper location of air entry suction point in engine bay compartment, suitable design for air filter box (volume), duct designs etc. Further design improvement are possible with an addition of tuned resonators in the system. An addition of resonator have major effect seen in reducing air induction noise and to meet target Sound Pressure Levels (SPL). But at the same time, selecting the correct type of resonator, its position & volume, frequency/s band at which resonator is tuned are important parameters.

Structural adhesive is a good alternative to provide required strength at joinery of similar and dissimilar materials. Adhesive joinery plays a critical role to maintain structural integrity during vehicle crash scenario. Robust adhesive failure definitions are critical for accurate predictions of structural performance in crash Computer Aided Engineering (CAE) simulations. In this paper, structural adhesive material characterization challenges like comprehensive In-house testing and CAE correlation aspects are discussed. Considering the crash loading complexity, test plan is devised for identification of strength and failure characteristics at 0°, 45°, 75°, 90°, and Peel loading conditions. Coupon level test samples were prepared with high temperature curing of structural adhesive along with metal panels. Test fixtures were prepared to carryout testing using Instron VHS machine under quasi-static and dynamic loading.

Engine Stop/Start System (ESS) promises to reduce greenhouse emissions and improve fuel economy of vehicles. Previous work of the Authors was concentrated on bridging the gap of improvement in fuel economy promised by ESS under standard laboratory conditions and actual driving conditions. Findings from the practical studies lead to a conclusion that ESS is not so popular among the customers, due to the complexities of the system operation and poor integration of the system design with the driver behavior. In addition, due to various functional safety requirements, and traffic conditions, actual benefits of ESS are reduced. A modified control algorithm was proposed and proven for the local driving conditions in India. The ways in which a given driver behaves on the controls of the vehicles like Clutch and Brake Pedals, Gear Shift Lever were not uniform across the demography of study and varied significantly.

In this study we will be discussing two issues related to vibrations which effect car owners. The first one, called lateral shake, can be described as a lateral vibration felt by customer in low speed of around 1200rpm, when vehicle shakes severely in Y-direction. The vibration is significantly felt at the thighs of passengers. A 16DOF rigid body model is established to simulate the power train & body system. The second vibration issue, called drive away shudder (also known as clutch judder/chatter/shudder) is a vibration felt by customers at the time of marching off. The vibration is significantly felt at the time of clutch engagement as a shiver in vehicle. While the common solution of shudder is to optimize clutch friction & engagement, in this study solution has been provided by optimizing the power train mounting system. Clutch shudder is observed on a medium sized car when driven in the range of 10-20 Km/h.

The AMT (Automated Manual Transmission) has attracted increasing interest of automotive researches, because it has some advantages of both MT (Manual Transmission) and AT (Automatic Transmission), such as low cost, high efficiency, easy to use and good comfort. The hill-start assistance is an important feature of AMT. The vehicle will move backward, start with jerk, or cause engine stalling if failed on the slope road. For manual transmission, hill-start depends on the driver's skills to coordinate with the brake, clutch and throttle pedal to achieve a smooth start. However, with the AMT, clutch pedal is removed and therefore, driver can’t perceive the clutch position, making it difficult to hill-start with AMT without hill-start control strategy. This paper discussed about the hill start control strategy and its functioning.

DFSS is a disciplined problem prevention approach which helps in achieving the most optimum design solution and provides improved and cost effective quality products. This paper presents the implementation of DFSS method to design a distinctive cooling system where engine is mounted in the rear and radiator is mounted in the front of the car. In automobile design, a rear-engine design layout places the engine at the rear of the vehicle. This layout is mainly found in small, entry level cars and light commercial vehicles chosen for three reasons - packaging, traction, and ease of manufacturing. In conventional Passenger cars, a radiator is located close to the engine for simple packaging and efficient thermal management. This paper is about designing a distinctive cooling system of a car having rear mounted engine and front mounted radiator.

An emissions, combustion noise and performance study were conducted to explore the effects of two different multiple injections strategies on emissions, combustion noise and performances without altering EGR %. The experiments were done on a six cylinder inline CRDI diesel production engine. The aim of this study is to improve performances (brake specific fuel consumption [BSFC], torque) and combustion noise (reduction) using multiple injection strategies without violating emission regulations. The other objective of this carried-out analysis is to examine the influence of different operating parameters (Speed and Load) and main injection timing combined, on same multiple injection strategies (Pilot- main – after {PMA}and Early - pilot- main –after {EPMA}) by means of analyzing emissions/soot, combustion noise and performances data.

In a heavy commercial vehicle, the engine cooling package is designed by considering peak heat load on the vehicle cooling system from an engine end. In cooling systems, the major unit that consumes most power from the engine is the engine cooling fan. It was seen from the vehicle measured duty cycle data, for most of the time engine operates at part load condition. Regardless of demand from the engine cooling system, engine fan was operating continuously at equivalent speed of the engine. This results in continuous consumption of productive engine power from the fan end ultimately affecting vehicle fuel economy. The present study shows that low idle speed viscous fan has the potential to meet stringent engine cooling performance requirements and consumes less engine power throughout an actual vehicle duty cycle. Experiments were conducted on test vehicle with different fan speeds.

Depletion of fossil fuel reserves, the unsteadiness of their prices and the increasingly stricter exhaust emission legislation put forward attention of world towards use of alternate fuels. The ever increasing demand for ecologically friendly vehicles can be met by use of clean fuels like Compressed Natural Gas (CNG) and Hydrogen (H2). Lower carbon to hydrogen ratio of CNG makes it a cleaner fuel, due to this CNG is gaining popularity as an internal combustion (IC) engine fuel in transport sector. Hydrogen fuel for IC engines is also being considered as a future fuel due to its simple carbon less structure. However, several obstacles have to be overcome before widespread utilization of hydrogen as an IC engine fuel can occur in the transport sector. The 18 percent hydrogen enriched CNG fuel referred to as HCNG has the potential to lower emissions and could be considered a first step towards promotion of a Hydrogen economy.

Spot welding is the primary joining method used in automobiles. Spot-weld plays a major role to maintain vehicle structural integrity during impact tests. Robust spot weld failure definitions is critical for accurate predictions of structural performance in safety simulations. Spot welds have a complex metallurgical structure, mainly consisting of fusion and heat affected zones. For accurate material property definitions in simulation models, huge number of inputs from test data is required. Multiple tests, using different spot weld joinery configurations, have to be conducted. In order to accurately represent the spot-weld behavior in CAE, detailed modeling is required using fine mesh. The current challenge in spot-weld failure assessment is developing a methodology having a better trade-off between prediction accuracy, testing efforts and computation time. In view of the above, cohesive zone models have been found to be very effective and accurate.

Better ride and comfort, enhanced safety, reliability and durability, lower running cost as well as cost of ownership continue to be challenges for automotive OEMs. Higher fuel efficiency is considered as USP not only for lower running cost but also is hygiene factor from sustainability point of view. This has necessitated the need for Augmenting Light weighting horizon in automotive OEMs. Augmenting this leads to invention of innovative materials and processes for emerging cost competitive market. This paper focuses on technology efforts towards augmenting light weighting Horizon in Automotive. Light weighting concepts being explored by OEMs with the help of automotive component manufacturers from Powertrain - Engines & Transmission, Chassis and Suspension are discussed.

Vehicle incab booming perception, a low frequency response of the structure to the various excitations presents a challenging task for the NVH engineers. The excitation to the structure causing boom can either be power train induced, depending upon the number of cylinders or the road inputs, while transfer paths for the excitation is mainly through the power train mounts or the suspension attachments to the body. The body responds to those input excitations by virtue of the dynamic behavior mainly governed by its modal characteristics. This paper explains in detail an integrated approach, of both experimental and numerical techniques devised to investigate the mechanism for boom noise generation. It is therefore important, to understand the modal behavior of the structure. The modal characteristics from the structural modal test enable to locate the natural frequencies and mode shapes of the body, which are likely to get excited due to the operating excitations.

Improvised Explosive Devices (IEDs) and Anti-Tank (AT) mines are a significant threat for military vehicles and their occupants. These explosive devices are designed for the destruction and damage of armored and other vehicles, by using them in battle fields on routes of army vehicles. The blast event results in effects like shockwave, fragments, fire, gases, blast overpressure as well as the vertical impulse load. A blast event affects occupants inside the vehicle in the form of various types of injuries (lower leg, spinal, chest, head etc) and trauma. The Lower leg is the foremost injured body region in a blast event. The term lower leg is used to designate the tibia, fibula and the foot/ankle complex in this paper. Detonations occurring under a vehicle produce high velocity floorboard flutter/deformation and transmit axial loads to lower leg and create injuries.

Restraints systems (airbags and seat belts) have been proven to be very effective in occupant protection in crashes. Timely deployment of these devices is very essential for meeting performance requirements. Precision and reliability in restraints deployments demand selection of a robust sensing configuration that caters to the wide variations of real world. This paper highlights complexities involved in engineering of restraints sensing configurations through different case studies on vehicle programs. The paper explains the need for restraints sensing configuration optimization and well defined sensing strategies for a robust solution in real world. A methodology is discussed to achieve good discrimination between crashes of different types and severities. Virtual and physical test data collected at different stages of vehicle development is used. It is found that criteria for threshold levels in restraints sensing requires efforts to identify real world usage variations.