Search Results

This specification covers an aluminum alloy in the form of plate 4.001 to 10.000 inches (101.60 to 254.00 mm), inclusive, in nominal thickness.

The documents listed in this ballot are being proposed for reaffirmation

This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number (IN) as assigned to vehicle engines, transmissions, and transaxles. The IN is used for tracking or traceability of these components. In adhering to these recommended practices, facility of application in factory production and appearance quality are matters for manufacturer control. Reference SAE J853.

This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and appropriate inhibitors, for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).

This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and borates of glycol ethers, and appropriate inhibitors for use in the braking system of any motor vehicle, such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR) or a terpolymer of ethylene, propylene, and a diene (EPDM).

Titanium alloy specification for bars, forgings, and flash welded rings.

This SAE Recommended Practice provides an orderly series for designating the thickness of unocated and coated hot-rolled and cold-rolled sheet and strip. This document also provides methods for specifying thickness tolerances.

This test method specifies the operating procedures for a controlled-irradiance, xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test duration, as well as any exceptions to the specimen preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as the use of optical filter combinations, is to be agreed upon by contractual parties.

This SAE Recommended Practice defines the minimum performance and dimensional requirements for quick connect couplings between flexible tubing or hose and rigid tubing or tubular fittings used in coolant systems. This document applies to automotive and light duty truck applications under the following conditions: a Gasoline, diesel, hybrid, and electrical propulsion cooling systems. b Operating pressure up to 206 kPa (30 psi). c Operating temperatures from -40 °C (-40 °F) to 125 °C (260 °F). Quick connect couplings function by joining the connector to a mating end form, typically without the use of tools. The requirements stated in this document apply to new connectors in assembly operations unless otherwise indicated.

This SAE Standard covers general and dimensional specifications for the Code 62 metric (Type 1) and inch (Type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS and FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flange clamps are not for new design. The flanged heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections. The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values. The following general specifications supplement the dimensional data contained in the tables with respect to all unspecified detail.

This SAE Standard is intended for all sizes of fuel filters, so a variety of test stands may be required depending upon flow rate. The low contamination level, downstream clean-up filter, and short duration of the test ensure that the particle retention ability of the filter is measured in a single pass, as no appreciable loading or regression will occur.

The objective of this glossary is to establish uniform definitions of parts and terminology for engine cooling systems. Components included are all those through which engine coolant is circulated: water pump, engine oil cooler, transmission and other coolant-oil coolers, charge air coolers, core engine, thermostat, radiator, external coolant tanks, and lines connecting them.

This SAE Standard covers steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See Part 2, Table 7 for hose operating temperature ranges and identification codes.

This Abstract Syntax Notation (ASN.1) file precisely specifies the structure of the data used to support the implementation of SAE International Standard 2945/6. Using the ASN.1 specification, a compiler tool can be used to produce encodings as required by the encoding rules identified in the standard. Both this file and the SAE J2735 ASN.1 files are necessary to collectively implement the data exchange described in the J2945/6. The combined library can be used by any application (along with the additional logic of the application) to exchange the data over an interface conformant to J2945/6. SAE J2945/6 specifies the interface and requirements for Cooperative Adaptive Cruise Control (CACC) and Platooning. It provides the information necessary to build interoperable systems that support CACC, which rely on the exchange of Cooperative Control Messages.

This Abstract Syntax Notation (ASN.1) file precisely specifies the structure of the data used to support the implementation of SAE International Standard 2945/6. Using the ASN.1 specification, a compiler tool can be used to produce encodings as required by the encoding rules identified in the standard. Both this file and the SAE J2735 ASN.1 files are necessary to collectively implement the data exchange described in the J2945/6. The combined library can be used by any application (along with the additional logic of the application) to exchange the data over an interface conformant to J2945/6. SAE J2945/6 specifies the interface and requirements for Cooperative Adaptive Cruise Control (CACC) and Platooning. It provides the information necessary to build interoperable systems that support CACC, which rely on the exchange of Cooperative Control Messages.

This SAE Standard specifies the general requirements and test methods for non-shielded, high-voltage ignition cable assemblies.

Creation of standardized wording for the cut length of weld wire provides standard lengths based on industry equipment and to allow other lengths as specified by the purchaser as requested

This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this specification is intended to cover the test methods, design, and performance requirements of optional features for additional power, clean ground for electronic functions, video, data communication, and supplementary electric brake control.

This document contains procedures for testing performance of SMB-style electrical terminals, connectors and components for coaxial cable connection systems intended for road vehicle applications. These are often called FAKRA II designs. This specification does not apply to the Non RF portion of a Hybrid RF connection system. The intent of this specification is to qualify sealed and unsealed RF connectors that operate at frequencies from DC to 6 GHz. The characteristic impedance of the SMB/FAKRA connection system is 50 ohms however this specification does not exclude the use of these RF connectors on non-50 ohm cables or systems. This specification does not apply to single conductor wire or twisted pair connection systems. This specification (along with SAE/USCAR 18) is designed to provide the mechanical and electrical data required to insure that assemblies from various manufacturers will perform reliably in actual conditions.