Search Results

SAE J115 specifies the relevant ISO standards for application to safety labels for use on off-road work machines as defined in SAE J1116.

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

This SAE Recommended Practice describes a test method for determination of heavy truck (Class VI, VII, and VIII) tire force and moment properties under cornering conditions. The properties are acquired as functions of normal force and slip angle using a sequence specified in this practice. At each normal force increment, the slip angle is continually ramped or stepped. The data are suitable for use in vehicle dynamics modeling, comparative evaluations for research and development purposes, and manufacturing quality control. This document is intended to be a general guideline for testing on an ideal machine. Users of this SAE Recommended Practice may modify the recommended protocols to satify the needs of specific use-cases, e.g., reducing the recommended number of test loads and/or pressures for benchmarking purposes. However, due care is necessary when modifying the protocols to maintain data integrity.

This SAE Standard establishes the maximum gradient rating during hopper discharge of self-propelled, driver-operated sweepers and scrubbers as defined by SAE J2130-1 and SAE J2130-2.

SAE J3078/6 specifies a test method for simulating solar heating in the laboratory and measuring the radiant heat energy from a natural or simulated source. It is applicable to off-road self-propelled work machines as defined in SAE J1116 and tractors and machinery for agriculture and forestry as defined in ANSI/ASAE S390.

The following list consists of hose data provided as of December 2022, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table, Table 1) along with the test results.

This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.

This SAE Recommended Practice provides design, test, and performance guidelines on the comfort, fit, and convenience for active restraint systems for heavy trucks and multipurpose passenger vehicle applications over 10000 pounds gross vehicle weight rating (GVWR). The information pertains to the forward facing seating positions.

This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting, clamshell, dragline, magnet, pile driver, or similar service.

This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers that use broom means for sweeping and collection, together with either a mechanical- or pneumatic-conveyance system for the transfer of “sweepings” into a collection hopper.

This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.

This specification covers polythioether rubber fuel resistant sealing compounds, supplied as a two-component system, which cure rapidly when exposed to a cure on demand (CoD) light source used to initiate a reaction that generates crosslinking of sealant polymers. Type 2 compounds also cure at ambient conditions, without light exposure.

This SAE information report covers the basic guidelines concerning off-road tire conditions that warrant replacement, removal, or repair. This material can assist the tire user in establishing specific written procedures for each job site.

This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: a. Tracking Transmitter b. Tracking Receiver c. Telemetry Device d. Remote Display This type of tracking equipment is typically used with Horizontal Earthboring Machines as defined in SAE J2022. The purpose of this document is to define common terms and commercial specifications associated with tracking equipment used in the horizontal earthboring industry.

The following list consists of hose data provided as of December, 2021, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table, Table 1) along with the test results.

This SAE Standard specifies the operating procedures for a controlled irradiance, xenon-arc apparatus used for the accelerated exposure of various exterior automotive materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers. Any deviation to this test method, such as filter combinations, is to be agreed upon by contractual parties.

This SAE Standard provides safety requirements for vacuum excavation and sewer cleaning equipment. This document is not intended to cover equipment addressed by other on-road federal, state, and local regulations. Truck-mounted or trailer-mounted vehicles are required to meet local or regional on-road requirements, as applicable.

This SAE Surface Vehicle Recommended Practice applies to cranes when used in lifting crane service which are equipped with rope drum rotation indicating devices.

The purpose of this SAE Standard is to specify the procedure for measuring the bank angle of motorcycles.

This SAE Recommended Practice (RP) describes a test method for determination of heavy truck (Class VI, VII, and VIII) tire force and moment properties under straight-line braking conditions. The properties are acquired as functions of normal force and slip ratio using a sequence specified in this practice. At each normal force increment, the slip ratio is continually changed by application of a braking torque ramp. The data are suitable for use in vehicle dynamics modeling, comparative evaluations for research and development purposes, and manufacturing quality control. This document is intended to be a general guideline for testing on an ideal machine. Users of this RP may modify the recommended protocols to satify the needs of specific use-cases; e.g., reducing the recommended number of test loads and/or pressures for benchmarking purposes. However, due care is necessary when modifying the protocols to maintain data integrity.