Search Results

Standard

Estimated Mechanical Properties and Machinability of Steel Bars

2024-03-04

CURRENT

J1397_202403

This SAE Information Report is intended to provide a guide to mechanical and machinability characteristics of some SAE steel grades. The ratings and properties shown are provided as general information and not as requirements for specifications unless each instance is approved by the source of supply. The data are based on resources which may no longer be totally accurate. However, this report is retained as a service in lieu of current data.

Standard

Glossary of Carbon Steel Sheet and Strip Terms

2019-07-29

CURRENT

J940_201907

This glossary is intended to provide engineers, metallurgists, and production personnel with uniform definitions of commonly used carbon sheet and strip terms. The glossary serves to supplement information and photographs reported in SAE J810, J763, J877, J863, and J403. Many of the terms listed apply only to hot-dipped zinc-coated products or to uncoated products. The letter C following the term identifies a term applying to coated materials, while the letters NC identify a term applying to uncoated materials. Where no identification is provided, the term is common to both.

Standard

Solders

2018-08-24

CURRENT

J473_201808

The choice of the type and grade of solder for any specific purpose will depend on the materials to be joined and the method of applying. Those with higher amounts of tin usually wet and bond more readily and have a narrower semi-molten range than lower amounts of tin. For strictly economic reasons, it is recommended that the grade of solder metal be selected that contains least amount of tin required to give suitable flowing and adhesive qualities for application. All the lead-tin solders, with or without antimony, are usually suitable for joining steel and copper base alloys. For galvanized steel or zinc, only Class A solders should be used. Class B solders, containing antimony usually as a substitute for some of the tin or to increase strength and hardness of the filler metal, form intermetallic antimony-zinc compounds, causing the joint to become embrittled. Lead-tin solders are not recommended for joining aluminum, magnesium, or stainless steel.

Standard

Sintered Powder Metal Parts: Ferrous

2018-08-24

CURRENT

J471_201808

Powder metal (P/M) parts are manufactured by pressing metal powders to the required shape in a precision die and sintering to produce metallurgical bonds between the particles, thus generating the appropriate mechanical properties. The shape and mechanical properties of the part may be subsequently modified by repressing or by conventional methods such. as machining and/or heat treating. While powder metallurgy embraces a number of fields wherein metal powders may be used as raw materials, this standard is concerned primarily with information relating to mechanical components and bearings produced from iron-base materials.

Standard

Wrought Nickel and Nickel-Related Alloys

2018-02-15

CURRENT

J470_201802

This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.

Standard

Magnetic Particle Inspection

2018-01-10

CURRENT

J420_201801

The scope of this SAE Information Report is to provide general information relative to the nature and use of magnetic particles for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of magnetic particle testing, and as a guide to more extensive references.

Standard

Wrought Aluminum Applications Guidelines

2018-01-10

CURRENT

J1434_201801

This report approaches the material selection process from the designer's viewpoint. Information is presented in a format designed to guide the user through a series of decision-making steps. "Applications criteria" along with engineering and manufacturing data are emphasized to enable the merits of aluminum for specific applications to be evaluated and the appropriate alloys and tempers to be chosen.

Standard

Automotive Metallurgical Joining

2018-01-10

CURRENT

J836_201801

This report is an abbreviated summary of metallurgical joining by welding, brazing, and soldering. It is generally intended to reflect current usage in the automotive industry; however, it does include some of the more recently developed processes. More comprehensive coverage of materials, processing details, and equipment required may be found in the Welding Handbook, Soldering Manual, and other publications of the American Welding Society and the American Society for Testing and Materials. AWS Automotive Welding Committee publications on Recommended Practices are particularly recommended for the design or product engineer. This report is not intended to cover mechanical joining such as rivets or screw fasteners, or chemical joining processes such as adhesive joining.

Standard

Wrought Copper and Copper Alloys

2018-01-10

CURRENT

J463_201801

This standard1 describes the chemical, mechanical, and dimensional requirements for a wide range of wrought copper and copper alloys used in the automotive and related industries.

Standard

Engine Poppet Valve Information Report

2018-01-10

CURRENT

J775_201801

This specification supplies engineers and designers with: a Poppet valve nomenclature b Poppet valve alloy designations c Chemical compositions of poppet valve alloys d A guide to valve alloy metallurgy and heat treatments e General information on properties of valve alloys f A guide to the application of valve alloys g A description of valve design and construction, and their relation to valve alloy selection h Valve gear design considerations that affect valves

Standard

Bearing and Bushing Alloys

2018-01-10

CURRENT

J459_201801

The bearing performance of steel backed half bearings, bushings, and washers is dependent on the properties and thickness of the lining alloy, the strength and dimensional stability of the steel backing (usually SAE 1010) and the strength of the bond between the lining alloy and the backing. This SAE Information Report is primarily concerned with the properties of the lining alloys used in automotive applications, in particular, the crankshaft bearings of the internal combustion engine.

Standard

General Information - Chemical Compositions, Mechanical and Physical Properties of SAE Aluminum Casting Alloys

2018-01-10

CURRENT

J452_201801

The SAE Standards for aluminum casting alloys cover a wide range of castings for general and special use, but do not include all the alloys in commercial use. Over the years, aluminum alloys have been identified by many numbering systems as shown in Table 1. Presently, SAE is recommending the use of the UNS Numbering System to identify these materials. The castings are made principally by sand cast, permanent mold, or die cast methods; however, shell molding, investment casting, plaster cast, and other less common foundry methods may also be used. If the alloys listed do not have the desired characteristics, it is recommended that the manufacturers of aluminum castings be consulted.

Standard

Methods of Measuring Decarburization

2018-01-10

CURRENT

J419_201801

This report covers the recommended practice for the evaluation and measurement of decarburization in ferrous material. Included are definitions of types with charts and micrographs and methods most commonly used for the measurement of decarburization.

Standard

Microscopic Determination of Inclusions in Steels

2018-01-10

CURRENT

J422_201801

This recommended microscopic practice for evaluating the inclusion content in steel has been developed as a practical method of quantitatively determining the degree of cleanliness of steel. This method has been established as a reasonable control for steel mill operations and acceptance for production manufacturing. It has been widely accepted for carbon and alloy steel bars, billets, and slabs. Exceptions are resulfurized grades which are outside the limits of these photomicrographs and the high carbon bearing quality steels which are generally classified using ASTM E 45-60T, Method A, Jernkontoret Charts.

Standard

Surface Hardness Testing with Files

2018-01-10

CURRENT

J864_201801

Hardness testing with files consists essentially of cutting or abrading the surface of metal parts, and approximating the hardness by the feel, or extent to which, the file bites into the surface. The term "file hard" means that the surface hardness of the parts tested is such that a new file of proven hardness will not cut the surface of the material being tested.

Standard

Infrared Testing

2018-01-09

CURRENT

J359_201801

The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references.

Standard

Abrasive Wear

2018-01-09

CURRENT

J965_201801

An enormous economic loss, as well as a waste of natural resources, is incurred world-wide as a result of wear of components and tools. Any effort expended in an attempt to reduce this loss is indeed worthwhile. The purpose of this SAE Information Report is to present the current state of knowledge of abrasive wear. This report, therefore, covers wear, or the undesired removal of metal by mechanical action, caused by abrasive particles in contact with the surface. It does not concern metal-to-metal wear or wear in the presence of an abrasive free lubricant. Abrasive wear occurs when hard particles, such as rocks, sand, or fragments of certain hard metals, slide or roll under pressure across a surface. This action tends to cut grooves across the metal surface, much like a cutting tool. Abrasive wear is of considerable importance in any part moving in relation to an abrasive.

Standard

Cleanliness Rating of Steels by the Magnetic Particle Method

2018-01-09

CURRENT

J421_201801

This SAE Recommended Practice provides a rating procedure for the cleanliness rating of steels by the magnetic particle method. The procedure is based on counting the number of indications (frequency) and employs a weighted value to obtain a severity factor. The method outlined is similar to that described in SAE Aerospace Material Specification AMS 2301.

Standard

Ultrasonic Inspection

2018-01-09

CURRENT

J428_201801

The scope of this SAE Information report is to provide basic information on ultrasonics, as applied in the field of nondestructive inspection. References to detailed information are listed in Section 2.

Standard

Magnesium Casting Alloys

2018-01-09

CURRENT

J465_201801

This document has not changed other than to put it into the new SAE Technical Standards Board Format This SAE Standard covers the most commonly used magnesium alloys suitable for casting by the various commercial processes. The chemical composition limits and minimum mechanical properties are shown. Over the years, magnesium alloys have been identified by many numbering systems, as shown in Table 1. Presently, SAE is recommending the use of the use of the UNS numbering system to identify those materials. Other equally important characteristics such as surface finish and dimensional tolerances are not covered in this standard.