Refine Your Search

Date

Date

Topic

Topic

Exteriors Steel Textile and Flexible Plastics Committee Forming

Search Results

Viewing 1 to 20 of 45
123Next >Last >>
Sort by published
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim
2022-10-04
CURRENT
J361_202210
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100 hue test as specified in ASTM E1499.
Standard

Fiberboard Test Procedure
2022-08-26
CURRENT
J315_202208
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Outdoor Weathering of Exterior Materials
2022-05-18
CURRENT
J1976_202205
This test method specifies the exposure racks, black boxes, and instrumentation, which shall be used for the outdoor weathering of materials for automotive exterior application.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim
2021-12-30
HISTORICAL
J361_202112
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100 Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Standard

Test Method for Determining Cold Cracking of Flexible Plastic Materials
2021-09-15
CURRENT
J323_202109
This SAE Recommended Practice is applicable for determining the cold characteristics of flexible plastic materials, as applicable. It consists of three different methods for determining low-temperature properties of materials depending on type of material and end use. The method used shall be as specified by the contractual parties.
Standard

Fiberboard Crease Bending Test
2019-10-31
CURRENT
J119_201910
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Design Guidelines for Fiberboard Materials
2019-09-25
CURRENT
J1774_201909
This document provides information on the various fiberboard products, which are available for automotive application. It is intended to give engineers and designers a better understanding of product usage, characteristics, properties and industry terminology. The following sections cover these topics: 2 General Product Information 3 Design Characteristics 4 Physical/Mechanical Properties 5 Fiberboard Definitions In sections 2, 3 and 4 the fiberboard products are categorized. These sections give an overview of product types, with general information about characteristics and properties. In cases where product categories encompass more than one material or material grade, ranges were established to cover all of the products in that category. The individual companies that supply fiberboard products should be consulted for specific information about a particular product or application.
Standard

Standard Classification System for Fiberboards
2014-06-04
HISTORICAL
J1323_201406
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
Standard

Glossary of Fiberboard Terminology
2014-01-23
HISTORICAL
J947_201401
This information report presents the terminology and definitions as used in the fiberboard industry.
Standard

Determination of the Fogging Characteristics of Interior Automotive Materials
2013-12-06
WIP
J1756
1.1 This recommended practice describes two methods for determining the tendency of interior materials used in automobiles and other vehicles to (a) produce a light scattering deposit (fog) on a glass surface, or (b) produce a measurable deposit (mass) on aluminum foil. 1.2 This document is applicable to the measurement of a fog condensate on glass or aluminum foil surfaces within the limits of the test conditions. 1.3 It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to its use.
Standard

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Air-Cooled Xenon-Arc Apparatus
2012-11-19
CURRENT
J2019_201211
This SAE Standard specifies the operating procedures for a controlled irradiance, air-cooled xenon-arc apparatus used for the accelerated exposure of various automotive exterior materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
Standard

Design Guidelines for Fiberboard Materials
2010-06-21
HISTORICAL
J1774_201006
This document provides information on the various fiberboard products, which are available for automotive application. It is intended to give engineers and designers a better understanding of product usage, characteristics, properties and industry terminology. The following sections cover these topics: 2 General Product Information 3 Design Characteristics 4 Physical/Mechanical Properties 5 Fiberboard Definitions In sections 2, 3 and 4 the fiberboard products are categorized. These sections give an overview of product types, with general information about characteristics and properties. In cases where product categories encompass more than one material or material grade, ranges were established to cover all of the products in that category. The individual companies that supply fiberboard products should be consulted for specific information about a particular product or application.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim
2010-06-16
HISTORICAL
J361_201006
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim.
Standard

Fiberboard Crease Bending Test
2010-05-10
HISTORICAL
J119_201005
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Fiberboard Test Procedure
2010-03-02
HISTORICAL
J315_201003
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Test Method for Determining Cold Cracking of Flexible Plastic Materials
2009-11-09
HISTORICAL
J323_200911
This SAE Recommended Practice is applicable for determining the cold characteristics of flexible plastic materials, as applicable. It consists of three different methods for determining low-temperature properties of materials depending on type of material and end use. The method used shall be as specified by the contractual parties.
123Next >Last >>
X