Search Results

This document describes a practical system for a user to determine observer-to-aircraft distances. These observer-to-aircraft distances can be either closest point of approach (CPA) distances during field measurements or overhead distances during acoustic certification tests. The system uses a digital camera to record an image of the subject aircraft. A method of using commercial software to obtain the distance from such an image is presented. Potential issues which may affect accuracy are discussed.

This SAE Aerospace Information Report (AIR) describes procedures for calculating fuel consumption for civil jet airplanes through all modes of operation for all segments of a flight. Turboprop and piston airplanes, as well as helicopters or unconventional aircraft, are not included in this AIR. The principle purpose of these procedures is to assist model developers in calculating airplane fuel consumption in a consistent and accurate manner that can be used to address various environmental assessments including those related to policy decisions and regulatory requirements. This AIR is intended to directly support the emission calculations documented in AIR5715. The models described in this AIR are intended to be used from the start of the takeoff roll to the end of the ground roll; taxi fuel consumption models are not included. If modelers have access to higher fidelity methods, they should use those methods in lieu of the ones in this AIR.

This document presents a practical method for calculating atmospheric absorption for wide-band sounds analyzed with one-third octave-band filters, called the SAE Method. The SAE Method utilizes pure-tone attenuation algorithms originally published in ISO 9613-1 and ANSI S1.26-1995 to calculate path-length attenuation at mid-band frequencies. The equations introduced in this standard transform the pure-tone, mid-band attenuation to one-third octave-band attenuation. The purpose of this guidance document is to extend the useful attenuation range of the Approximate Method outlined in ANSI S1.26-1995, and to replace ARP866A. Calculation of sound attenuation caused by mechanisms other than atmospheric absorption such as divergence, refraction, scattering due to turbulence, ground reflections, or non-linear propagation effects, is outside the scope of this document.

ARP876 is intended to provide specific recommended procedures for the prediction of gas turbine jet exhaust system noise sources. Procedures are issued as separate sections, to allow for future updating as additional methods, consistent with state-of-the-art, become available.

This Aerospace Information Report provides guidelines for hardware design. Guidelines on such items as engine types, test arrangements, and test purposes that would benefit from the use of an inflow control device during static noise testing are outside the scope of this report.

Recommendations presented in this document are intended primarily for the acquisition of far-field noise data. The test engine is to be appropriately configured and operated so that the sound pressure levels obtained are consistent with the specific objectives of the test. The principal output of the data reduction system is one-third octave band sound pressure levels. However, when appropriate, data may be recorded for purposes of broader or narrower bandwidth analysis.

The scope of this ARP embraces the description of a configuration for a ground-plane microphone installation that may be used to determine sound pressure levels equivalent to those which would have been measured in an acoustic freefield at the microphone location. The one-third - octave-band center-frequency range over which equivalent freefield sound pressure levels may be obtained is from as low as 50 Hz to at least as high as 10,000 Hz. The specific application of the measurement technique described in this ARP is the determination of the equivalent freefield sound pressure levels of the noise produced by propeller-driven light aircraft, in flight, for sound incidence angles within 30 degrees of the normal to the ground. For larger angles to the normal, additional adjustments may be necessary which are outside the scope of this ARP.

This method estimates noise for both single and tandem main rotor helicopters except for approach where it applies to single rotor designs only. It does not apply to coaxial rotor designs. Due to lack of available data, application of the method has not been evaluated for application to tiltrotor, or other VTOL configurations, when operating in the helicopter mode. Since there are substantial differences between helicopter rotors included in the data base, and tiltrotor rotors, application to VTOL configurations other than helicopters is not advised. Application is limited to helicopters powered by turboshaft engines and does not apply to helicopters powered by reciprocating engine, tip jets or other types of power plants. It provides noise information using basic operating and geometric information available in the open literature. To keep the method simple, it generates A-weighted sound levels, and Sound Exposure Levels precluding the necessity for spectral details.

ARP876 is intended to provide specific recommended procedures for the prediction of gas turbine jet exhaust system noise sources. Procedures are issued as separate Sections, to allow for future updating as additional methods, consistent with state-of-the-art, become available.

This Aerospace Information Report provides guidelines for hardware design. Guidelines on such items as engine types, test arrangements, and test purposes that would benefit from the use of an inflow control device during static noise testing are outside the scope of this report.

Recommendations presented in this document are intended primarily for the acquisition of far-field acoustical data. The test engine is to be appropriately configured and operated so that the acoustical signals generated are consistent with the specific objectives of the test. The principal output of the data reduction system is one-third octave band sound pressure levels. However, broader or narrower bandwidth analysis of the recorded data may also be accomplished when appropriate. Although not specifically intended to apply to special purpose engine noise testing (for example, tests involving unique instrumentation or procedures to identify specific noise sources), some of the practices described herein may be appropriate for such testing. Specification of reference conditions is outside the scope of this document although procedures to adjust data to a reference condition are described in 7.2.4.

ARP876 is intended to provide specific recommended procedures for the prediction of gas turbine jet exhaust system noise sources. Procedures are issued as separate Sections, to allow for future updating as additional methods, consistent with state-of-the-art, become available.