Search Results

This paper reports the study of the effects of alternative diesel fuel and the impact for the air-fuel mixture preparation. The injection process characterization has been carried out in a non-evaporative high-density environment in order to measure the fuel injection rate and the spatial and temporal distribution of the fuel. The injection and vaporization processes have been characterized in an optically accessible single cylinder Common Rail diesel engine representing evaporative conditions similar to the real engine. The tests have been performed by means of a Bosch second generation common rail solenoid-driven fuel injection system with a 7-holes nozzle, flow number 440 cc/30s @100bar, 148deg cone opening angle (minisac type). Double injection strategy (pilot+main) has been implemented on the ECUs corresponding to operative running conditions of the commercial EURO 5 diesel engine.

In this work a detailed model to simulate the transient behavior of catalytic converters is presented. The model is able to predict the unsteady and reacting flows in the exhaust ducts, by solving the system of conservation equations of mass, momentum, energy and transport of reacting chemical species. The en-gine and the intake system have not been included in the simulation, imposing the measured values of mass flow, gas temperature and chemical composition as a boundary condition at the inlet of the exhaust system. A detailed analysis of the diffusion stage triggering is proposed along with simplifications of the physics, finalized to the reduction of the calculation time. Submodels for water condensation and its following evaporation on the monolith surface have been taken into account as well as oxygen storage promoted by ceria oxides.

The flame front propagation in normal and abnormal combustion was investigated. Cycle-resolved flame emission imaging was applied in the combustion chamber of a port fuel injection boosted spark ignition engine. The engine was fuelled with a mixture of 90% iso-octane and 10% n-heptane by volume (PRF90). The effect of fuel injection phasing was studied. The combustion process was followed from the flame kernel formation until the opening of the exhaust valves. Different phenomena correlated to the abnormal combustion were analysed. Detailed information on ignition surfaces, end-gas auto-ignitions and knock were obtained. The appearance of autoignition centres in the end gas was evaluated in terms of timing, location and frequency of occurrence.

A computational, three-dimensional approach to investigate the behavior of diesel soot particles in the micro-channels of wall-flow Diesel Particulate Filters is presented. The KIVA3V CFD code, already extended to solve the 2D conservation equations for porous media materials [1], has been enhanced to solve in 2-D and 3-D the governing equations for reacting and compressible flows through porous media in non axes-symmetric geometries. With respect to previous work [1], a different mathematical approach has been followed in the implementation of the numerical solver for porous media, in order to achieve a faster convergency as source terms were added to the governing equations. The Darcy pressure drop has been included in the Navier-Stokes equations and the energy equation has been extended to account for the thermal exchange between the gas flow and the porous wall.

The present work focuses on the simulation of the hydrodynamics, transient filtration/loading and catalytic/NO2-assisted regeneration of Diesel after-treatment systems. A 1D unsteady model for compressible and reacting flows for the numerical simulation of the behavior of Diesel Oxidation Catalysts (DOCs) and Diesel Particulate Filters (DPFs) has been developed. The numerical model is able to keep track of the amount of soot in the flow; the increasing of back-pressure through the exhaust system (mainly due to the Diesel Particulate Filter) can be predicted by the calculation of the permeability variation of the porous wall, as the soot particles goes inside the DPF. A sub-model for the regeneration of the collected soot has been developed: the collected particulate is oxidized by the Oxygen (O2) and by the Nitrogen Dioxide (NO2).

A new approach for the fluid-dynamic simulation of the Diesel Particulate Filters (DPF) has been developed. A mathematical model has been formulated as a system of nonlinear partial differential equations describing the conservation of mass, momentum and energy for unsteady, compressible and reacting flows, in order to predict the hydrodynamic characteristics of the DPF and to study the soot deposition mechanism. In particular, the mass conservation equations have been solved for each chemical component considered, and the advection of information concerning the chemical composition of the gas has been figured out for each computational mesh. A sub-model for the prediction of the soot cake formation has been developed and predictions of soot deposition profiles have been calculated for different loading conditions. The results of the simulations, namely the calculated pressure drop, have been compared with the experimental data.

This work describes an experimental and numerical investigation of the thermal transient of i.c. engine exhaust systems. A prototype of exhaust system has been investigated during a NEDC cycle in two different configurations. Firstly an uncoated catalyst has been adopted to consider only the effect of the gas-wall heat transfer. The measurements have been repeated on the same exhaust system equipped with a coated catalyst to point out the contribution of the chemical reactions to the thermal transient of the system. The measured values have been compared to the predicted results carried out with a 1D thermo fluid dynamic code, developed in-house to account for the thermal transient of the system and the chemical reactions occurring in the catalyst.

Two different optical techniques for detection, sizing and counting nanoparticles were applied to undiluted exhaust from 16 v–1900 cc Common Rail diesel engine upstream and downstream a Catalyzed Diesel Particulate Filter (CDPF): Broadband Ultraviolet–Visible Extinction and Scattering Spectroscopy (BUVESS) and Laser Induced Incandescence (LII). They are powerful “in situ” and non-intrusive techniques; they are able to measure mass concentration and size of particles, considering their chemical properties. BUVESS overcomes the intrinsic limitations of single wavelength techniques because it takes advantage of data at several wavelengths to retrieve primary particle size distribution. LII measures mean size of primary particles with a large dynamic range, not limited by aggregate size and by complex retrieving procedure.

Actual emission legislation limits strongly the amount of pollutant in the atmosphere from internal combustion engine. In particular diesel engines widely emit NOx and particulate matter (PM). The last one has principally a carbonaceous nature and presents micronic and submicronic particles extremely dangerous for human health since it could deposit in the lung. In this work, a technique based on broadband ultraviolet (UV) visible scattering and extinction is applied inside a transparent DI CR diesel engine in order to analyze the soot evolution and oxidation. The study is carried out with particular detail for different injection strategies characterized of two and three injections per cycle, Pre+Main and Pre+Main+Post, considering the late combustion before the exhaust stroke. The analysis is performed in terms of size, mass concentration, and chemical and physical nature.

The paper describes the results of a parallel 1D thermo-fluid dynamic simulation and experimental investigation of a DI turbocharged Diesel engine. The attention has been focused on the overall engine performances (air flow, torque, power, fuel consumption) as well as on the emissions (NO and particulate) along the after-treatment system, which presents a particulate filter. The 1D research code GASDYN for the simulation of the whole engine system has been enhanced by the introduction of a multi-zone quasi-dimensional combustion model for direct injection Diesel engines. The effect of multiple injections is taken into account (pilot and main injection). The prediction of NO and soot has been carried out respectively by means of a super-extended Zeldovich mechanism and by the Hiroyasu kinetic approach.

The DEXA Cluster consisted of three closely interlinked projects. In 2003 the DEXA Cluster concluded by demonstrating the successful development of critical technologies for Diesel exhaust particulate after-treatment, without adverse effects on NOx emissions and maintaining the fuel economy advantages of the Diesel engine well beyond the EURO IV (2000) emission standards horizon. In the present paper the most important results of the DEXA Cluster projects in the demonstration of advanced particulate control technologies, the development of a simulation toolkit for the design of diesel exhaust after-treatment systems and the development of novel particulate characterization methodologies, are presented. The motivation for the DEXA Cluster research was to increase the market competitiveness of diesel engine powertrains for passenger cars worldwide, and to accelerate the adoption of particulate control technology.

The paper describes the research work carried out on the thermo-fluid dynamic modeling of an S.I. engine coupled to the vehicle in order to predict the engine and tailpipe emissions during the ECE European driving cycle. The numerical code GASDYN has been extended to simulate the engine + vehicle operation during the first 90 seconds of the NEDC driving cycle, taking account of the engine and exhaust system warm-up after the cold start. The chemical composition of the engine exhaust gas is calculated by means of a thermodynamic multi-zone combustion model, augmented by kinetic emission sub-models for the prediction of pollutant emissions. A simple procedure has been implemented to model the vehicle dynamic behavior (one degree of freedom model). A closed-loop control strategy (proportional-derivative) has been introduced to determine the throttle opening angle, corresponding to the engine operating point when the vehicle is following the ECE cycle.

Multidimensional simulation of the soot formation process in a diesel engine is realised exploiting quantitative measurements of the soot volume fraction and diameter obtained by optical techniques. Broadband extinction and scattering measurements are performed on an optically accessible 4-stroke engine where a forced air motion allows a strong prevalence of the premixed stage of combustion with respect to the non-premixed one. Two semi-empirical models for soot formation are tested in the numerical simulation, which is performed using a customized version of the KIVA-3 code. The need of furnishing coherent values of the soot particles density and mean diameter to the one of the two models requiring this kind of information, is highlighted and demonstrated to be crucial in avoiding over-prediction of the soot concentration.

Polychromatic extinction and chemiluminescence techniques, from ultraviolet to visible, were applied in an optical diesel engine, in order to analyze the temporal and spatial evolution of a high pressure fuel jet interacting with a swirling air motion. A fully flexible Common Rail fuel injection system equipped with a single hole nozzle was used. The experiments were performed at fixed engine speed and air/fuel ratio for three injection strategies. The first one consisted of a main injection to compare with those operating at low pressure injection. The other ones were based on a pilot and main injections, typical of current direct injection diesel engines, with different dwell time. A detailed investigation of the mixture formation process inside the combustion chamber during the ignition delay time was performed. The liquid and vapor fuel distribution in the combustion chamber was obtained analyzing the polychromatic extinction spectra.

The paper describes the research work concerning the simulation of 1D unsteady reacting flows in s.i. engine pipe-systems, including pre-catalysts and main catalysts. The numerical model GASDYN has been developed to enable the concurrent prediction of the wave motion in the intake and exhaust ducts, the chemical composition of the gas discharged by the cylinder of a s.i. engine, the chemical and thermal behavior of catalytic converters. The effect of considering the transport of chemical species with reactions in gas phase (post-oxidation of unburned HC in the exhaust manifold) and in solid phase (conversion of pollutants in the catalyst) on the predicted wave motion is reported.

Nowadays 1D fluid dynamic models are widely used by engine designers, since they can give sufficiently accurate predictions in short times, allowing to support the optimization and development work of any prototype. According to the last requirements in terms of pollutant emission control, some enhancements have been introduced in the 1D code GASDYN, to improve its ability in predicting the composition of the exhaust gas discharged by the cylinders and the transport of the chemical species along the exhaust system. The main aspects of the methods adopted to model the combustion process and the related formation of pollutants are described in the paper. To account for the burnt gas stratification, two different approaches have been proposed, depending on the expected turbulence levels inside the combustion chamber. The reliability of the simulation of the pollutant formation process has been enhanced by the integration of the thermodynamic module with the Chemkin code.

Conventional methods to measure gas concentrations and, in particular, NO are typically based on sampling by valve, sample treatment and subsequent analysis. These methods suffer low spatial and temporal resolution. The introduction of high energy lasers in combination with fast detection systems allowed to detect the NO distribution inside optically accessible Diesel engines. In this paper, a high spatial and temporal resolution in-situ technique based on ultraviolet - visible absorption spectroscopy is proposed. The characterization of the combustion process by the detection of gaseous compounds from the start of combustion until the exhaust phase was performed. In particular, this technique allows the simultaneous detection of NO and OH absolute concentrations inside an optically accessible Diesel combustion chamber.

Non-intrusive diagnostic techniques based on broadband (190-550 nm) extinction and scattering spectroscopy were applied at undiluted exhaust Common- Rail (CR) diesel engine in real time. The influence of load and Exhaust Gas Recirculation (EGR) on soot mass concentration, size distribution of emitted particles and NO concentration was analyzed. NO concentration was evaluated by ""in-situ"" ultraviolet-visible absorption measurements and compared with those obtained by conventional analyzer. The extinction and scattering spectra were compared with those evaluated by the Lorenz-Mie model for spherical particles in order to retrieve the size, the number concentration of the emitted particles and particulate mass. The optical measurements showed that new generation diesel engines, in spite of a drastic reduction of the exhaust mass concentration, caused the emission in the atmosphere of high number concentration of carbonaceous nanoparticles.

Quantitative measurements of the soot volume fraction and diameter performed by spectroscopic techniques within the combustion chamber of a diesel engine are employed to aid multidimensional simulation of the soot formation and oxidation processes. By changing the start of fuel injection, two different operating conditions are considered, which are characterized by different relative importance of the premixed to the diffusive stage of the combustion process. Both the reduced models by Hiroyasu et al., and the one by Nagle and Strikland- Constable are employed within the numerical simulation. The reason of the peculiar over-prediction of soot concentration of the latter model is discussed and related to the need of furnishing coherent values of the soot particle density and mean diameter.

The optimization of diesel engine performance and emissions can be achieved through a better understanding of the in-cylinder combustion process. Advanced non-intrusive optical techniques are providing new tools for investigating the thermo-fluid dynamics processes as well as they are contributing to develop predictive models for DI diesel combustion. High-speed images of spray and flame evolution as well as UV-visible chemiluminescence measurements were carried out in an optical 0.5-liter, single-cylinder, four-stroke, direct- injection diesel engine equipped with a prototype four valves cylinder head and a fully flexible CR injection system. In order to evaluate the effect of different injection strategies on the combustion process, measurements were performed varying injection parameters. The ignition location and time were individuated by combustion visualization and detection of radical species, obtained by chemiluminescence measurements.