Search Results

The current research octane number (RON) and motor octane number (MON) gasoline tests are inadequate for describing the auto-ignition reactivity of fuels in homogeneous charge compression ignition (HCCI) combustion. Intake temperature and engine speed are two important parameters when trying to understand the fuel auto-ignition reactivity in HCCI combustion. The objective of this study was to understand the effect of high intake temperature (between 100 and 200 °C) and engine speed (600 and 900 rpm) on the auto-ignition HCCI reactivity ratings of fuels using an instrumented Cooperative Fuel Research (CFR) engine. The fuels used for this study included blends of iso-octane/n-heptane, toluene/n-heptane, ethanol/n-heptane, and gasolines with varying chemical compositions and octane levels. The CFR engine was operated at 600 and 900 rpm with an intake pressure of 1.0 bar and an excess air ratio (lambda) of 3.

Stringent emission regulations and the anticipated climate change call for a paradigm shift in the design of the conventional internal combustion engines. One way to combat this problem is oxy-fuel combustion in which the combustion products are mainly water vapor and carbon dioxide. Water vapor can be easily separated by condensation and carbon dioxide is then easily captured and stored. However, many technical challenges are associated with this mode of combustion. There are many challenges facing oxy-fuel combustion before it find its way to commercial production especially for internal combustion engines. One such challenge is the relatively high temperature of the oxy-fuel combustion. A solution to this problem is the recirculation of the generated CO2 to moderate the in-cylinder temperature. Therefore, careful study of the effect of recirculating the CO2 back to combustion chamber is needed before the implementation of such a concept.

A new concept utilizing multiple fuel injectors was proven effective at reducing heat transfer losses by directing spray plumes further away from the combustion chamber walls. In this concept, two injectors are mounted close to the rim of the piston bowl and point in opposite directions to generate swirling in-cylinder bulk motion. Moreover, a new flat-bowl piston design was also proposed in combination with the multiple fuel injectors for even larger improvements in thermal efficiency. However, all tests were performed at low-to-medium load conditions with no significant EGR. Modern engine concepts, such as the double compression-expansion engine (DCEE), have demonstrated higher thermal efficiency when operated at high-load conditions with a large amount of EGR for NOx control. Thus, this study aims to assess the effectiveness of the multiple-fuel-injector system under such conditions. In this study, a number of 3-D CFD simulations are performed using the RANS technique in CONVERGE.

The improvement of the indicated thermal efficiency of an argon power cycle (replacing nitrogen with argon in the combustion reaction) is investigated in a CFR engine at high compression ratios in homogeneous charge compression ignition (HCCI) mode. The study combines the two effects that can increase the thermodynamic efficiency as predicted by the ideal Otto cycle: high specific heat ratio (provided by argon), and high compression ratios. However, since argon has relatively low heat capacity (at constant volume), it results in high in-cylinder temperatures, which in turn, leads to the occurrence of knock. Knock limits the feasible range of compression ratios and further increasing the compression ratio can cause serious damage to the engine due to the high pressure rise rate caused by advancing the combustion phasing.

This study investigates particulate matter (PM) and regulated emissions from renewable rapeseed oil methyl ester (RME) biodiesel in pure and blended forms and contrasts that to conventional diesel fuel. Environmental and health concerns are the major motivation for combustion engines research, especially finding sustainable alternatives to fossil fuels and reducing diesel PM emissions. Fatty acid methyl esters (FAME), including RME, are renewable fuels commonly used from low level blends with diesel to full substitution. They strongly reduce the net carbon dioxide emissions. It is largely unknown how the emissions and characteristics of PM get altered by the combined effect of adding biodiesel to diesel and implementing modern engine concepts that reduce nitrogen oxides (NOx) emissions by exhaust gas recirculation (EGR).

Engine experiments were performed on a single-cylinder heavy-duty engine at relatively high loads to investigate the regions where the combustion characteristics are unchanged regardless of the fuel octane number. Primary Reference Fuels (PRFs) and three different commercial fuels with RON values ranging from 0 to 100 were tested in this study. A sweep of net indicated mean effective pressure (IMEPNet) of 5 to 20 bar, absolute intake pressure of 1.5 to 2.8 bar, exhaust gas recirculation (EGR) of 0 to 40%, and fuel injection pressure of 700 to 1400 bar were performed to investigate the combustion characteristics, ignition delay time, combustion duration, efficiency, and emissions. At the highest load point (IMEPNet = 20 bar), all the fuels burn as in conventional diesel combustion. Despite the wide range of octane numbers, all fuels had similar ignition delay time, combustion duration, indicated efficiency, and emissions at 10 to 20 bar IMEPNet.

This study examined the octane boosting effects of γ-valerolactone, a fuel derived from lignocellulosic biomass, under Homogeneous Charge Compression Ignition (HCCI) combustion mode. The experiments were performed in a Cooperative Fuel Research (CFR) engine under four sets of conditions defined by the combinations of intake temperatures and rotation speed. Octane boosting effects were rated with FACE (Fuel for Advanced Combustion Engine) J gasoline as a base fuel. Due to the non-miscibility of γ-valerolactone into FACE J, a new approach was proposed in which the octane boosting effect of a mixture comprised up of two-third γ-valerolactone and one-third ethanol was investigated. To evaluate the effect of γ-valerolactone, the octane boosting effect of pure ethanol into FACE J was also investigated such that comparison can be drawn. Further attempts were made to extract the octane boosting effects of pure γ-valerolactone.

Global warming and the increasingly stringent emission regulations call for alternative combustion techniques to reduce CO2 emissions. Oxy-fuel combustion is one of those techniques since the combustion products are easily separated by condensing the water and storing CO2. A problem associated with the burning of fuel using pure oxygen as an oxidant is that it results in high adiabatic flame temperature. This high flame temperature is decreased by introducing a thermal buffer to the system. A thermal buffer in this context is any gas that does not participate in combustion but at the same time absorbs some of the released heat and thus decreases the temperature of the medium. Many experiments have been conducted to study oxy-fuel combustion in ICE using noble gases as thermal buffers. However, those experiments focused on using hydrogen as a fuel to avoid any build-up of CO2 in the system.

A large number of measurement techniques have been developed or adapted from other fields to measure various parameters of engine particulates. With the strict limits given by regulations on pollutant emissions, many advanced combustion strategies have been developed towards cleaner combustion. Exhaust gas recirculation (EGR) is widely applied to suppress nitrogen oxide (NOx) and reduce soot emissions. On the other hand, gasoline starts to be utilized in compression ignition engines due to great potential in soot reduction and high engine efficiency. New engine trends raise the need for good sensitivity and suitable accuracy of the PM measurement techniques to detect particulates with smaller size and low particulate mass emissions. In this work, we present a comparison between different measurement techniques for particulate matter (PM) emissions in a compression ignition engine running on gasoline fuel. A wide-range of EGR was used with lambda varied from 3 down to 1.

In the engine community, gasoline compression ignition (GCI) engines are at the forefront of research and efforts are being taken to commercialize an optimized GCI engine in the near future. GCI engines are operated typically at Partially Premixed Combustion (PPC) mode as it offers better control of combustion with improved combustion stability. While the transition in combustion homogeneity from convectional Compression Ignition (CI) to Homogenized Charge Compression Ignition (HCCI) combustion via PPC has been comprehensively investigated, the physical and chemical effects of fuel on GCI are rarely reported at different combustion modes. Therefore, in this study, the effect of physical and chemical properties of fuels on GCI is investigated. In-order to investigate the reported problem, low octane gasoline fuels with same RON = 70 but different physical properties and sensitivity (S) are chosen.

A new approach for investigating combustion behavior of practical fuels under homogeneous charge compression ignition (HCCI) conditions was developed with the help of a cooperative fuel research (CFR) engine. The method uses a set of two pressure-temperature diagrams and two charts, each with an octane number scale based on primary reference fuels (PRF), created from experimental results by sweeping the intake temperature. The two pressure-temperature diagrams report conditions leading to the start of the low temperature combustion and the start of the main combustion, respectively. Additional two charts -- required compression ratio and fraction of low temperature heat release charts -- describe global combustion behavior and the importance of the low temperature combustion. Each diagram and chart, together with their respective octane number scale, allow to examine the combustion behavior of practical fuels by comparing their combustion behavior with those of the PRFs.

Argon replacing Nitrogen has been examined as a novel engine cycle reaching higher efficiency. Experiments were carried out under Homogeneous Charge Compression Ignition (HCCI) conditions using a single cylinder variable compression ratio Cooperative Fuel Research (CFR) engine. Isooctane has been used as the fuel for this study. All the parameters were kept fixed but the compression ratio to make the combustion phasing constant. Typical engine outputs and emissions were compared to conventional cycles with both air and synthetic air. It has been found that the compression ratio of the engine must be significantly reduced while using Argon due to its higher specific heat ratio. The resulting in-cylinder pressure was lower but combustion remains aggressive. However, greater in-cylinder temperatures were reached. To an end, Argon allows gains in fuel efficiency, in unburned hydrocarbon and carbon monoxide, as well as in indicated efficiency.

NOx pollution from diesel engines has been stated as causing over 10 000 pre-mature deaths annually and predictions are showing that this level will increase [1]. In order to decrease this growing global problem, exhaust after-treatment systems for diesel engines have to be improved, this is especially so for vehicles carrying freight as their use of diesel engines is expected to carry on into the future [2]. The most common way to reduce diesel engine NOx out emissions is to use SCR. SCR operates by injecting aqueous Urea solution, 32.5% by volume (AUS-32), that evaporates prior the catalytic surface of the SCR-catalyst. Due to a catalytic reaction within the catalyst, NOx is converted nominally into Nitrogen and Water. Currently, the evaporative process is enhanced by aggressive mixer plates and long flow paths.

Partially premixed combustion (PPC) is an operating mode that lies between the conventional compression ignition (CI) mode and homogeneous charge compression ignition (HCCI) mode. The combustion in this mixed mode is complex as it is neither diffusion-controlled (CI mode) nor governed solely by chemical kinetics (HCCI mode). In this study, CFD simulations were performed to evaluate flame index, which distinguishes between zones having a premixed flame and non-premixed flame. Experiments performed in the optical engine supplied data to validate the model. In order to realize PPC, the start of injection (SOI) was fixed at −40 CAD (aTDC) so that a required ignition delay is created to premix air/fuel mixture. The reference operating point was selected to be with 3 bar IMEP and 1200 rpm. Naphtha with a RON of 77 and its corresponding PRF surrogate were tested. The simulations captured the general trends observed in the experiments well.

Partially premixed combustion (PPC) is an advanced combustion strategy that has been proposed to provide higher efficiency and lower emissions than conventional compression ignition, as well as greater controllability than homogeneous charge compression ignition (HCCI). Stratification of the fuel-air mixture is the key to achieving these benefits. The injection strategy, injector-piston geometry design and fuel properties are factors commonly manipulated to adjust the stratification level. In the authors’ previous research, the effects of injection strategy and fuel properties on the stratification formation process were investigated. The results revealed that, for a direct-injection compression ignition engine, by sweeping the injection timing from −180° aTDC (after top dead center) to −20° aTDC, the sweep could be divided into three different regimes: an HCCI regime, a Transition regime and a PPC regime, based on the changing of mixture stratification conditions.

Homogeneous charge compression ignition (HCCI) experiments were run with the aid of a Cooperative fuel research (CFR) engine, operating at 600 rpm and under very lean conditions (ϕ = 0.3). This study seeks to examine the combustion behavior of different fuels by finding the pressure-temperature (p-t) conditions that instigate the start of combustion, and the transition from low temperature combustion to principal combustion. The pressure-temperature diagram emphasizes p-t conditions according to their traces through the compression stroke. In each fuel tested, p-t traces were examined by a sweep of the intake temperature; and for each experimental point, combustion phasing was maintained at top dead center by adjusting the compression ratio of the engine. In addition to the p-t diagram, results were analyzed using a compression ratio-intake temperature diagram, which showed the compression ratio required with respect to intake temperature.

Due to their physical and chemical properties, alcohols such as ethanol and methanol when blended with gasoline provide high anti-knock quality and hence efficient engines. However, there are few promising properties of 1-butanol similar to conventional gasoline which make it a favorable choice for internal combustion engines. Previously the author showed that by blending ethanol and methanol with low octane fuels, non-linear increase in the HCCI fuel number occurs in HCCI combustion mode. Very few studies have been conducted on the use of 1-butanol in HCCI combustion mode, therefore for this work, 1-butanol with a RON 96 was selected as the high octane fuel. Three low octane fuels with octane number close to 70 were used as a base fuel. Two of the low octane fuels are Fuels for Advanced Combustion Engines (FACE gasolines), more specifically FACE I and FACE J and also primary reference fuel (PRF 70) were selected.

The present study experimentally examines the low-temperature autoignition area of isooctane within the in-cylinder pressure-in-cylinder temperature map. Experiments were run with the help of a Cooperative Fuel Research (CFR) engine. The boundaries of this engine were extended so that experiments could be performed outside the domain delimited by research octane number (RON) and motor octane number (MON) traces. Since homogeneous charge compression ignition (HCCI) combustion is governed by kinetics, the rotation speed for all the experiments was set at 600 rpm to allow time for low-temperature heat release (LTHR). All the other parameters (intake pressure, intake temperature, compression ratio, and equivalence ratio) were scanned, such as the occurrence of isooctane combustion. The principal results showed that LTHR for isooctane occurs effortlessly under high intake pressure (1.3 bar) and low intake temperature (25 °C).

Future internal combustion engines demand higher efficiency but progression towards this is limited by the phenomenon called knock. A possible solution for reaching high efficiency is Octane-on-Demand (OoD), which allows to customize the antiknock quality of a fuel through blending of high-octane fuel with a low octane fuel. Previous studies on Octane-on-Demand highlighted efficiency benefits depending on the combination of low octane fuel with high octane booster. The author recently published works with ethanol and methanol as high-octane fuels. The results of this work showed that the composition and octane number of the low octane fuel is significant for the blending octane number of both ethanol and methanol. This work focuses on toluene as the high octane fuel (RON 120). Aromatics offers anti-knock quality and with high octane number than alcohols, this work will address if toluene can provide higher octane enhancement.

The concept of Partially Premixed Combustion (PPC) in internal combustion engines has shown to yield high gross indicated efficiencies, but at the expense of gas exchange efficiencies. Most of the experimental research on partially premixed combustion has been conducted on compression ignition engines designed to operate on diesel fuel and relatively high exhaust temperatures. The partially premixed combustion concept on the other hand relies on dilution with high exhaust gas recirculation (EGR) rates to slow down the combustion which results in low exhaust temperatures, but also high mass flows over cylinder, valves, ports and manifolds. A careful design of the gas exchange system, EGR arrangement and heat exchangers is therefore of utter importance. Experiments were performed on a heavy-duty, compression ignition engine using a fuel consisting of 80 volume % 95 RON service station gasoline and 20 volume % n-heptane.