Refine Your Search

Date

Date

Topic

Topic

Engine cylinders Commercial vehicles Sensors and actuators Maintenance and Aftermarket SAE IC Powertrain Steering Committee

Search Results

Viewing 1 to 20 of 25
12Next >Last >>
Sort by published
Standard

Spark Arrester Test Procedure for Large Size Engines
2020-10-06
CURRENT
J342_202010
This SAE Recommended Practice establishes equipment and procedures for the evaluation of the effectiveness and other performance characteristics of spark arresters or turbochargers used on the exhaust system of large engines normally used in a railroad locomotive, stationary power plant, and other similar applications. This document does not cover applications requiring flame arresting, exhaust gas cooling, or isolation from explosive gases. Two test methods are presented: a laboratory test using ambient air (cold test) and an engine test using exhaust gases (hot test). The hot test is preferred. Arresters tested by the provisions of this document can be expected to perform as tested when tilted no more than 45 degrees from their normal position. Test results from a spark arrester or turbocharger evaluated by the hot test can be applied to different engines of similar design, provided the data shows it to be effective in the applicable flow ranges.
Standard

Spark Arrester Test Procedure for Large Size Engines
2013-03-26
HISTORICAL
J342_201303
This SAE Recommended Practice establishes equipment and procedures for the evaluation of the effectiveness and other performance characteristics of spark arresters or turbochargers used on the exhaust system of large engines normally used in a railroad locomotive, stationary power plant, and other similar applications. This document does not cover applications requiring flame arresting, exhaust gas cooling, or isolation from explosive gases. Two test methods are presented: a laboratory test using ambient air (cold test) and an engine test using exhaust gases (hot test). The hot test is preferred. Arresters tested by the provisions of this document can be expected to perform as tested when tilted no more than 45 degrees from their normal position. Test results from a spark arrester or turbocharger evaluated by the hot test can be applied to different engines of similar design, provided the data shows it to be effective in the applicable flow ranges.
Standard

SAE Design Guideline: Metal Belt Drive Continuously Variable Ratio (CVT) Automatic Transmissions
2011-09-12
CURRENT
J2525_201109
The purpose of this guideline is to provide the essential design considerations for the metal “V” belt variator used in continuously variable transmissions. Information from SAE papers, transmission manufacturers, and component manufacturers is provided to aid engineers in understanding the function and design methodology of the major components within the variator system. Recommended design practices are given based on current practices.
Standard

Engine Terminology and Nomenclature - General
2011-08-05
CURRENT
J604_201108
This SAE Recommended Practice is applicable to all types of reciprocating engines including two-stroke cycle and free piston engines, and was prepared to facilitate clear understanding and promote uniformity in nomenclature. Modifying adjectives in some cases were omitted for simplicity. However, it is good practice to use adjectives when they add to clarity and understanding.
Standard

Sleeve Type Half Bearings
2011-06-10
CURRENT
J506_201106
This SAE Standard defines the normal dimensions, dimensioning practice, tolerances, specialized measurement techniques, and glossary of terms for bearing inserts commonly used in reciprocating machinery. The standard sizes cover a range which permits a designer to employ, in proper proportion, the durability and lubrication requirements of each application, while utilizing the forming and machining practices common in manufacture of sleeve type half bearings. Not included are considerations of hydrodynamic lubrication analysis or mechanical stress factors of associated machine structural parts which determine the nominal sizes to be used, selection of bearing material as related to load carrying capacity, and economics of manufacture. For information concerning materials, see SAE J459 and SAE J460. These suggested sizes provide guidelines which may result in minimal costs of tooling but do not necessarily represent items which can be ordered from stock.
Standard

Guide to the Application and Use of Engine Coolant Pump Face Seals
2000-11-07
HISTORICAL
J1245_200011
This SAE Recommended Practice is intended as a guide in the usage of mechanical face seals for the engine coolant pump application. The main purpose of the document is to fill the void caused by the lack of a ready source of practical information on the design and use of the engine coolant pump face seal. Included in the document is a compilation of present practices, as in a description of the various types of seals, material combinations, design data, tolerances, drawing format, qualification and inspection information, and quality control data. The terminology used throughout the document is recommended and, through common usage, is hoped to promote uniformity in seal nomenclature.
Standard

SAE Design Guideline: Metal Belt Drive Continuously Variable Ratio (CVT) Automatic Transmissions
2000-03-27
HISTORICAL
J2525_200003
The purpose of this guideline is to provide the essential design considerations for the metal “V” belt variator used in continuously variable transmissions. Information from SAE papers, transmission manufacturers, and component manufacturers is provided to aid engineers in understanding the function and design methodology of the major components within the variator system. Recommended design practices are given based on current practices.
Standard

Seals—Testing of Radial Lip
1997-12-01
HISTORICAL
J110_199712
This SAE Recommended Practice covers equipment and procedures for general performance and low-temperature tests on radial lip type seals for rotating shafts. Three test sections are included: General Performance Test, Alternate General Performance Test, and Low-Temperature Test.
Standard

RUBBER RINGS FOR AUTOMOTIVE APPLICATIONS
1995-06-29
HISTORICAL
J120_199506
This SAE Recommended Practice covers the dimensional and material requirements of rubber O-rings for automotive application and rectangular section rubber seal rings for automotive applications.
Standard

ENGINE AND TRANSMISSION DIPSTICK MARKING
1995-06-29
HISTORICAL
J614_199506
This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.
Standard

ENGINE TERMINOLOGY AND NOMENCLATURE—GENERAL
1995-06-28
HISTORICAL
J604_199506
This SAE Recommended Practice is applicable to all types of reciprocating engines including two-stroke cycle and free piston engines, and was prepared to facilitate clear understanding and promote uniformity in nomenclature. Modifying adjectives in some cases were omitted for simplicity. However, it is good practice to use adjectives when they add to clarity and understanding.
Standard

SLEEVE TYPE HALF BEARINGS
1995-02-22
HISTORICAL
J506_199502
This SAE Standard defines the normal dimensions, dimensioning practice, tolerances, specialized measurement techniques, and glossary of terms for bearing inserts commonly used in reciprocating machinery. The standard sizes cover a range which permits a designer to employ, in proper proportion, the durability and lubrication requirements of each application, while utilizing the forming and machining practices common in manufacture of sleeve type half bearings. Not included are considerations of hydrodynamic lubrication analysis or mechanical stress factors of associated machine structural parts which determine the nominal sizes to be used, selection of bearing material as related to load carrying capacity, and economics of manufacture. For information concerning materials, see SAE J459 and SAE J460. These suggested sizes provide guidelines which may result in minimal costs of tooling but do not necessarily represent items which can be ordered from stock.
Standard

ENGINE WEIGHT, DIMENSIONS, CENTER OF GRAVITY, AND MOMENT OF INERTIA
1992-04-01
HISTORICAL
J2038_199204
This SAE Recommended Practice has been developed to provide a uniform method for reporting the weight, dimensions, center of gravity, and moment of inertia of internal combustion engines. SAE J2038 is not intended to cover the technical interface between the engine and transmission. To locate the rear of the engine crankshaft in relationship to the rear of the flywheel housing, refer to SAE J617.
Standard

SPARK ARRESTER TEST PROCEDURE FOR MEDIUM SIZE ENGINES
1991-01-01
HISTORICAL
J350_199101
This SAE Recommended Practice establishes equipment and procedures for testing spark arresters used on medium-size, single-position internal combustion engines, normally used in transportable, stationary, and vehicular applications, such as highway trucks, agricultural tractors, industrial tractors, other mobile equipment, and motorcycles. This document provides two methods of testing (laboratory testing and engine testing) which may be used to evaluate a spark arrester. It also includes special requirements for screen type devices and an endurance test procedure for screen type spark arresters.
Standard

ENGINE WEIGHT AND DIMENSIONS
1990-04-01
HISTORICAL
J2038_199004
This SAE Recommended Practice has been developed to provide a uniform method for reporting the weight and dimensions of internal combustion engines. SAE J2038 is not intended to cover the technical interface between the engine and transmission. To locate the rear of the engine crankshaft in relationship to the rear of the flywheel housing, refer to SAE J617.
Standard

SEALS - TESTING OF RADIAL LIP
1985-06-01
HISTORICAL
J110_198506
This SAE Recommended Practice covers equipment and procedures for general performance and low temperature tests on radial lip type seals for rotating shafts. Three test sections are included: General Performance Test, Alternate General Performance Test, and Low Temperature Test.
12Next >Last >>
X