Standard
NUT - HEX, PORT FITTING CONNECTOR, AMS5639, MJ THREAD, METRIC
2023-09-01
CURRENT
MA2521A
Search Results
Standard
NUT - HEX, BACK-UP RING, PORT FITTING CONNECTOR, AMS5639, MJ THREAD, METRIC
2023-09-01
CURRENT
MA2520A
Standard
Trademarks, Hydraulic System Component Manufacturers, Index of
2022-12-20
CURRENT
AIR1973B
This index of trademarks of current and former manufacturers of aerospace fittings, couplings, hoses, and tube support devices is within the scope of activities of the SAE G-3 Committee and available at the time of publication. Supplier markings from previous publication are maintained for component traceability. Suggestions for additional entries or corrections shall be sent to SAE in Warrendale, PA.
Standard
FITTING END ASSEMBLY, INTERNAL THREAD, RETAINED NUT, BEAM SEAL, DESIGN STANDARD
2022-08-05
CURRENT
AS4209E
Standard
PORT-FLUID CONNECTION, RING LOCKED INSERT, STANDARD DIMENSIONS FOR
2022-05-09
CURRENT
AS1958A
Standard
TUBE END - BEADED, DESIGN STANDARD
2020-12-10
CURRENT
AS5131A
Standard
FITTING END ASSEMBLY, INTERNAL THREAD, RETAINED NUT, BEAM SEAL, DESIGN STANDARD
2020-09-18
HISTORICAL
AS4209D
Standard
Clamp Selection and Installation Guide
2019-05-20
CURRENT
ARP1897A
This document is prepared as an aid in the selection of clamping devices and their use in aerospace equipment for the installation and support of tubing and wiring. For recommended installation practices, refer to ARP994.
Standard
Qualification of Hydraulic Tube Joints to Specified Flexure Fatigue Requirements
2019-01-03
WIP
ARP1258C
This SAE Aerospace Recommended Practice (ARP) establishes the method for qualification testing of tube joints and fitting attachments, using the flexure test method described in ARP1185. This qualification test method allows the determination of S-N type stress versus cycles or D-N type deflection versus cycles curves, as illustrated in AIR1418 as an alternate to flexure testing to a minimum endurance stress level.
Standard
SAFETY WIRE HOLES, HEX, FITTING, LOCATION OF, DESIGN STANDARD
2017-05-25
HISTORICAL
AS1043G
Standard
Fittings, Flanged to Beaded, Fluid Connection
2015-07-27
HISTORICAL
AS4875/2
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both flanged fitting ends and beaded hose connections for use in all types of fluid systems.
Standard
CLAMP, LOOP, TUBE 17-7 PH CRES, 500 °F
2015-04-23
HISTORICAL
AS85052/3A
Standard
CLAMP, LOOP, TUBE, 17-7PH, 275 °F, FUEL AND PETROLEUM BASED HYDRAULIC FLUID RESISTANT
2015-04-23
HISTORICAL
AS85052/1A
Standard
CLAMP, LOOP, TUBE 17-7PH CUSHION, SELF-LOCKING
2013-07-16
HISTORICAL
AS6264
Standard
PACKING, PREFORMED, AIR DUCT HOSE, GROUND COOLING
2013-01-07
CURRENT
AS38386/3
Standard
Contractile Strain Ratio Testing of Titanium Hydraulic Tubing
2013-01-07
CURRENT
AS4076
This SAE Aerospace Standard establishes the requirements and procedures for Contractile Strain Ratio (CSR) testing of cold-worked and stress-relieved titanium tubing such as Ti-3AI-2.5V tubing per AMS 4944.
Standard
CONNECTOR, AIR DUCT HOSE, GROUND COOLING, FEMALE
2013-01-07
CURRENT
AS38386/2A
Standard
CLIP, SPRING RETENTION - ELECTRICAL CABLE
2013-01-07
CURRENT
AS5117
Standard
Qualification of Hydraulic Tube Joints to Specified Flexure Fatigue Requirements
2013-01-02
CURRENT
ARP1258B
This SAE Aerospace Recommended Practice (ARP) establishes the method for qualification testing of tube joints and fitting attachments, using the flexure test method described in ARP1185. This qualification test method allows the determination of S-N type stress versus cycles or D-N type deflection versus cycles curves, as illustrated in ARP1418 as an alternate to flexture testing to a minimum endurance stress level.
Standard
Prestressing (Autofrettaging) of Hydraulic Tubing Lines
2013-01-02
HISTORICAL
AIR1379A
This AIR is intended to describe and document a process presently in use for proof testing, which at the same time improves the fatigue life of 304 1/8 hard CRES and 3Al-2.5V CWSR titanium hydraulic tubing lines.
