This index of trademarks of current and former manufacturers of aerospace fittings, couplings, hoses, and tube support devices is within the scope of activities of the SAE G-3 Committee and available at the time of publication. Supplier markings from previous publication are maintained for component traceability. Suggestions for additional entries or corrections shall be sent to SAE in Warrendale, PA.
These formulae shall be used to determine drop dimensions for simple bend tube fittings utilizing flare and flareless end connection designs from 0° to 90° used in aircraft and aerospace applications. Individual design standards shall specify parameters, such as centerline bend radius (R), straight tangent length to accommodate bending equipment (X1 and X2), and nut to be used.
This SAE Aerospace Standard (AS) establishes the requirements for 24 degree cone flareless fluid connection fittings and nuts, internally or externally swaged, preset, or welded sleeves for use in aircraft fluid systems at nominal operating pressures up to and including 3000 psi.
This specification covers the design requirements and test procedures for separable beam seal fittings which includes end fittings (see 2.3.4), fitting bodies (see 2.3.7), and boss fittings (see 2.3.2) for use in aerospace fluid systems. Design requirements are for class 3000 in corrosion resistant steel (15-5 PH, 17-4 PH CRES) only and for class 4000 in titanium alloy (Ti) and corrosion and heat-resistant steel (nickel alloy 718 CRES) only. Definition of fittings and related terms are defined in 2.3.
This SAE Aerospace Information Report (AIR) contains information relative to stresses and loads developed in tubes caused by tube deflections encountered in misaligned installations. Users are advised that when calculating the stresses and loads of a tubing system, the yield strength of existing loop clamp material is significantly lower than the tubing materials specified herein and should be considered.
This SAE Aerospace Information Report (AIR) presents flexure fatigue strength of tube fitting joints in the form of graphs showing applied deflection D and total calculated axial stress S versus number of cycles to failure N. The graphs have been prepared from data obtained by actual testing conducted in accordance with ARP1185.
This specification covers the requirements for aircraft, hydraulic, self-sealing, quick disconnect couplings, for use in Type II hydraulic systems (-65 to +275 °F temperature range) as defined by AS5440.
This SAE Aerospace Standard (AS) establishes the requirements for externally swaged titanium tube fittings on titanium and CRES tubing with flareless separable fitting for use in hydraulic supply and return aerospace fluid systems up to operating pressure of 5080 psig (35 000 kPa) maximum and an operating temperature range of -65 to +275 °F (-54 to +135 °C). This specification covers a common 5080 psi pressure titanium fitting that may be used for a range of operating pressures up to 5080 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS5959. The fitting operating pressure is based on the fitting thread pitch. Extra fine pitch for 5080 psi operating pressure and fine pitch for operating pressures 3000 psi and less. Table 12 shows applicable aerospace fitting part number standard and tubing materials and operating pressures.
This SAE Aerospace Standard (AS) establishes the requirements for axially swaged titanium fittings on titanium, CRES, and aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems up to operating pressure of 5080 psig (35000 kPa) maximum. The operating temperature range for titanium tubing and CRES tubing is -65 to +275 °F (-54 to +135 °C) and the operating temperature range for aluminum return system tubing is -65 to +225 °F (-54 to +107 °C). This specification covers a common 5080 psi pressure titanium fitting that may be used for a range of operating pressures up to 5080 psi with different tubing materials and tubing wall thicknesses and is assembled with the same tooling in accordance with AS5959. The flareless fitting operating pressure is based on the fitting thread pitch. Extra fine pitch is used for 5080 psi operating pressure and fine pitch for operating pressures 3000 psi and less.
This document is prepared as an aid in the selection of clamping devices and their use in aerospace equipment for the installation and support of tubing and wiring. For recommended installation practices, refer to ARP994.
This document defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic braid reinforced, hose assembly suitable for use in 400 °F (204 °C), 5080 psi (35000 kPa) aircraft hydraulic systems.
This standard defines the requirements for bulk protective sleeve to provide fire resistance for aircraft hose assemblies, which will enable these assemblies to meet the requirements of AS1055. NOTE: Use of this sleeve does not eliminate the need to demonstrate that the sleeved assemblies will meet the applicable requirements of AS1055.
This SAE Aerospace Standard (AS) establishes the requirements for 24° cone flareless fluid connection fittings and nuts, internally or externally swaged, preset, or welded sleeves for use in aircraft fluid systems at nominal operating pressures up to and including 3000 psi.