Refine Your Search

Date

Date

Topic

Topic

Vehicle dynamics Inspections Tests and Testing AGE-3 Aircraft Ground Support Equipment Committee

Search Results

Viewing 1 to 20 of 38
12Next >Last >>
Sort by published
Standard

Impulse Towing Loads
2023-04-03
CURRENT
AIR6906
This SAE Aerospace Information Report (AIR) provides information about impulse loads that occur during normal aircraft towing operations. An instrumented tow bar was used to characterize towing loads. Suggestions to minimize impulse loads by reducing the tow bar to tow vehicle gap are described.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2022-09-30
CURRENT
ARP5283B
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
Standard

Measurement of Exterior Sound Level of Specialized Aircraft Ground Support Equipment
2021-09-30
CURRENT
ARP1801A
The scope of this SAE Recommended Practice covers specialized internal combustion engine powered equipment used in support of aircraft operations. The equipment may be self-propelled, truck mounted, trailer mounted, skid mounted or stationary. It does not include construction equipment or equipment designed primarily for operation on highways or within factories or building areas. NOTE: Equivalent methodology is provided in (CEN) EN 1915-4, Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction, to be used for measurements conforming to the EU Machinery Directive
Standard

Method of Testing Pre-Conditioned Air Equipment
2021-04-08
CURRENT
ARP5374B
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

Aircraft Tow Bar
2021-04-08
CURRENT
ARP1915E
This SAE Aerospace Recommended Practice (ARP) specifies dimensional and physical requirements of tow bar connections to tractor and aircraft (see Figure 1). It is applicable to all types of commercial transport category aircraft tow bar. The purpose of this SAE Aerospace Recommended Practice (ARP) is to standardize tow bar attachments to airplane and tractor according to the mass category of the towed aircraft, so that one tow bar head with different shear levels can be used for all aircraft that are within the same mass category and are manufactured in compliance with AS1614 or ISO 8267.
Standard

Aircraft Ground Support Equipment - Wind Stability Determination
2020-04-29
CURRENT
ARP1328D
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a Uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b Uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c Standardization of specific types of interlock systems and actuation systems, d A standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e A standard method for testing these systems.
Standard

Aircraft Markings for Ground Support Equipment Alignment
2020-04-24
CURRENT
AS6896
The purpose of this document is to provide a standard for aircraft fuselage markings located at the doors used for ground servicing operations. These markings can be used by all GSE that will dock at the aircraft. These markings may be used for one or several phases of the GSE positioning relative to the aircraft process: GSE alignment during approach, GSE final docking, and GSE auto leveling. It is not the purpose of this standard to describe the different technologies, cameras, or other equipment that can be mounted on GSE to utilize these markings. The aircraft that may use these markings will have a fuselage diameter of 3 m or more.
Standard

Aircraft Ground Support Equipment - Wind Stability Determination
2017-05-04
HISTORICAL
ARP1328C
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c standardization of specific types of interlock systems and actuation systems, d a standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e a standard method for testing these systems.
Standard

Cushion Tow Hitches Test
2012-12-05
CURRENT
AIR1353C
The main purpose of this test was to determine the application advantages of cushion tow hitches in comparison to the commonly used rigid tow hitch type fitted on heavy aircraft towing tractors. As diverse opinions emerged about its suitability since the introduction on the market of this new tow hitch type, it was intended to physically measure and evaluate the damping capability of this cushioned tow link when applied in practice.
Standard

Aircraft Ground Support Equipment - Wind Stability Determination
2012-10-15
HISTORICAL
ARP1328B
This SAE Aerospace Recommended Practice (ARP) is intended to recommend: a uniform criteria for determination of wind loads that aircraft ground support equipment can encounter and yet allow personnel to work safely, b uniform systems for maintaining stability (i.e., stabilizers, outriggers, spring lockout devices), c standardization of specific types of interlock systems and actuation systems, d a standard formula with its associated design criteria for calculating the steady-state wind stability (i.e., tip point) for aircraft ground support equipment, e a standard method for testing these systems.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2012-09-24
HISTORICAL
ARP5283A
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
Standard

Aural Protector, Sound
2012-01-24
CURRENT
AS23899A
This specification covers the design and performance requirements for one type of sound aural protector.
Standard

Aircraft Tow Bar
2010-09-13
HISTORICAL
ARP1915D
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8600 kg (19 000 lb).
Standard

Method of Testing Pre-Conditioned Air Equipment
2008-04-15
HISTORICAL
ARP5374A
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
Standard

400 Hz Connection Aircraft Electrical Maintenance Procedures
2008-03-28
HISTORICAL
AIR4365A
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

Measurement of Exterior Sound Level of Specialized Aircraft Ground Support Equipment
2006-10-13
HISTORICAL
ARP1801
The scope of this recommended practice covers specialized internal combustion engine powered equipment used in the support of aircraft operations. The equipment may be self-propelled, truck mounted, trailer mounted, skid mounted or stationary. It does not include construction equipment or equipment designed primarily for operation on highways or within factories or building areas.
Standard

Cushion Tow Hitches Test
2006-02-09
HISTORICAL
AIR1353B
The main purpose of this test was to determine the application advantages of cushion tow hitches in comparison to the commonly used rigid tow hitch type fitted on heavy aircraft towing tractors. As diverse opinions emerged about its suitability since the introduction on the market of this new tow hitch type, it was intended to physically measure and evaluate the damping capability of this cushioned tow link when applied in practice.
Standard

Aircraft Tow Bar
2005-04-06
HISTORICAL
ARP1915C
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design considerations for transport aircraft tow bars. It does not cover the requirements for tow bars intended for aircraft with a maximum ramp mass (MRW) below 8,600 kg (19,000 lb).
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2005-02-10
HISTORICAL
ARP5283
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852A and ARP4853A. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, reduce the certified safe life limit of the nose gear, or induce a stability problem during pushback and/or maintenance towing operations. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only. It is not meant for dispatch (operational) towing (see definitions in Section 3). Dispatch towing imposes greater loads on nose gears and structure due to additional passenger, cargo, and fuel loads.
12Next >Last >>
X