This specification covers all aspects in Electrical Wiring Interconnection Systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles, and external pods.
The thermal modeling guidelines and best practices provided in this document are applicable to powered aerospace vehicle wires and wire bundles in thermal environments ranging from -65 to +260 °C (-85 to +500 °F) and pressures ranging from sea level to space vacuum. Currently the ARP only considers steady state and direct current conditions. The effects of wiring terminations and connectors are not addressed. Both can significantly impact the overall current derating and safety margins for a wiring system.
This document covers the general recommendations for Transverse Electromagnetic Mode (TEM) Transmission Lines intended for use in airborne systems (see 6.2.14). For U.S military applications, TEM Transmission Lines shall meet the requirements in accordance with MIL-T-81490. The follow index lists the recommended requirements and methods covered by the Aerospace Recommended Practice (ARP):
This SAE Aerospace Information Report (AIR) is limited to the subject of compatibility of wiring as part of aircraft Electrical Wiring and Interconnect Systems (EWIS) installed in and around aircraft fuel tanks.
This document presents design and application information which will allow optimized utilization of filter line wire and cable purchased to AS85485. Filter line wire is defined and design information is presented. The electrical and mechanical performance characteristics of the wire, along with recommended harnessing methods and techniques, are also presented.
Wire and cable products progress through a series of handling or operational steps from the time they leave the manufacturer, and until a finished harness or assembly is ready for installation on a vehicle. Throughout these many steps, environmental or processing conditions may be present which can generate damage detrimental to the wire or cable and/or its intended application.
It is the purpose of this document to present design recommendations that will provide a basis for satisfactory and safe electrical installations in transport aircraft. This document is not intended to be a complete electrical installation design handbook. However, the requirements for safety extend so thoroughly throughout the electric systems that few areas of the installation are untouched by the document. It is recognized that individual circumstances may alter the details of any design. It is, therefore, important that this document not be considered mandatory but be used as a guide to good electrical application and installation design. Transport aircraft electric systems have rapidly increased in importance over a number of years until they are now used for many functions necessary to the successful operation of the aircraft. An ever increasing number of these functions are critical to the safety of the aircraft and its occupants.
This specification covers all aspects in Electrical Wiring Interconnection Systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles, and external pods.
This ARP specifies the recommended methods of marking electrical wiring and harnesses to aid in the positioning/routing of electrical wiring, harnesses and cable assemblies.
This specification applies to complete cable assemblies (using either molded on or attachable plugs) used to connect external electric power to aircraft and to attachable plugs used as replacement for plugs damaged in service.
This SAE Aerospace Information Report (AIR) is limited to the subject of compatibility of wiring as part of aircraft Electrical Wiring and Interconnect Systems (EWIS) installed in and around aircraft fuel tanks.
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
This document covers the general recommendations for Transverse Electromagnetic Mode (TEM) Transmission Lines intended for use in airborne systems (see 6.2.14). For U.S military applications, TEM Transmission Lines shall meet the requirements in accordance with MIL-T-81490. The follow index lists the recommended requirements and methods covered by the Aerospace Recommended Practice (ARP):
This specification covers all aspects in electrical wire interconnection systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles and external pods.