Refine Your Search

Date

Date

Topic

Topic

Fuel lines Truck and Bus Total Vehicle Steering Committee Tires Test procedures

Search Results

Viewing 1 to 20 of 35
12Next >Last >>
Sort by published
Standard

Truck Tractor Semitrailer Interchange Coupling Dimensions
2017-08-09
CURRENT
J701_201708
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches. Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
Standard

Truck Tractor Semitrailer Interchange Coupling Dimensions
2014-01-03
HISTORICAL
J701_201401
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches. Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
Standard

Exterior Sound Level for Heavy Trucks and Buses
2011-09-12
CURRENT
J366_201109
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Fifth Wheel Kingpin Performance – Commercial Trailers and Semitrailers
2011-07-13
CURRENT
J133_201107
The purpose of this SAE Recommended Practice is to establish test procedures and minimum performance standards for kingpins and their supporting structure manufactured to SAE specifications. The dimensions shown in SAE J700 will permit the establishment of standard clearances in the installed condition which, in turn, will permit fifth wheel manufacturers to design their products to establish interchangeability with any kingpin made and installed to the SAE specification.
Standard

Measurement and Presentation of Truck Ride Vibrations
2011-05-17
CURRENT
J1490_201105
There are two ways to assess the characteristics of ride vibrations of a vehicle during its operation. Subjective evaluation and objective measurement. Subjective assessments of the ride vibrations experienced by drivers during ride evaluations are generally performed by a panel of drivers and/or passengers who are instructed to operate or ride a group of vehicles in a predetermined manner in order to subjectively assess the levels and characteristics of ride vibrations. Figures 6A through 6C show examples of subjective evaluation forms presently in use. The disadvantages of the subjective method include need for careful experimental design, need for statistically unbiased samples, complexity of human perceptions of vibrations, and difficulty in comparing qualitative data of vehicles evaluated at different times and/or by different groups of people. Often ride characterization is not an easy task using only qualitative or descriptive terms.
Standard

Rear Wheel Splash and Stone Throw Protection
2011-05-17
CURRENT
J682_201105
For guidance only in regard to highway commercial motor vehicles where protection to the rear against rear wheel splash and stone throw is deemed necessary, the following clearance specifications are recommended.
Standard

Tire Chain Clearance - Trucks, Buses (Except Suburban, Intercity, and Transit Buses), and Combinations of Vehicles
2011-05-17
CURRENT
J683_201105
The purpose of this SAE Information Report is to set up a guide as to body, frame, and wheel housing clearance to accommodate tire chains, and also the minimum bogie spacing to permit using chains on both axles. These dimensions apply to trucks, buses, and combinations of vehicles 10 001 lb (4535.06 kg) GVW and over, and are based upon recommendations of the Tire and Rim Association and of the National Association of Chain Manufacturers. The diagram shows clearance for chains over the tire ONLY and allowance must be made for spring deflections in determining fender clearance. See Figure 1 and Table 1.
Standard

Fifth Wheel Kingpin Performance—Commercial Trailers and Semitrailers
2003-10-27
HISTORICAL
J133_200310
The purpose of this SAE Recommended Practice is to establish test procedures and minimum performance standards for kingpins and their supporting structure manufactured to SAE specifications. The dimensions shown in SAE J700 will permit the establishment of standard clearances in the installed condition which, in turn, will permit fifth wheel manufacturers to design their products to establish interchangeability with any kingpin made and installed to the SAE specification.
Standard

Rear Wheel Splash and Stone Throw Protection
2003-01-01
HISTORICAL
J682_200301
For guidance only in regard to highway commercial motor vehicles where protection to the rear against rear wheel splash and stone throw is deemed necessary, the following clearance specifications are recommended.
Standard

Exterior Sound Level for Heavy Trucks and Buses
2001-04-27
HISTORICAL
J366_200104
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Trailer Axle Alignment
1999-03-24
HISTORICAL
J875_199903
The scope of this SAE Recommended Practice, trailer axle alignment, is to identify the dimensional limits of, and a method to, establish a perpendicular relationship between the king pin centerline and the axle centerline at its midpoint. Various types of equipment are commercially available which can be used for this measurement which provides varying degrees of accuracy, but none can be endorsed by SAE. The most fundamental methods of measurement will be described here, but other equipment is available if a greater degree of accuracy is desired.
Standard

Steady-State Circular Test Procedure for Trucks and Buses
1998-12-01
HISTORICAL
J2181_199812
This test procedure is used to determine the steady-state directional control response of vehicles by measuring steady-state cornering behavior. Due to the wide range of operational conditions to which a vehicle can be subjected, the results of this testing do not provide a complete description of a vehicle's total dynamic behavior; in particular, the procedure does not test the vehicle's response during transient maneuvers. To fully assess a vehicle's total dynamic behavior, it would be necessary to conduct other test procedures in order to evaluate the vehicle's performance as a whole. The extent of instrumentation and the required accuracy of the measurement will be dependent on the goals of the personnel conducting the test. If it is desired simply to determine the general performance characteristics of a vehicle, then this test can be conducted with minimal instrumentation and test item preparation.
Standard

TIRE CHAIN CLEARANCE—TRUCKS, BUSES (EXCEPT SUBURBAN, INTERCITY, AND TRANSIT BUSES), AND COMBINATIONS OF VEHICLES
1985-08-01
HISTORICAL
J683_198508
The purpose of this SAE Information Report is to set up a guide as to body, frame, and wheel housing clearance to accommodate tire chains, and also the minimum bogie spacing to permit using chains on both axles. These dimensions apply to trucks, buses, and combinations of vehicles 10 001 lb (4535.06 kg) GVW and over, and are based upon recommendations of the Tire and Rim Association and of the National Association of Chain Manufacturers. The diagram shows clearance for chains over the tire ONLY and allowance must be made for spring deflections in determining fender clearance. See Figure 1 and Table 1.
12Next >Last >>
X