Search Results

Abstract Biogas (60% methane–40% CO2 approximately) can be used in the reactivity-controlled compression ignition (RCCI) mode along with a high-reactivity fuel (HRF). In this work dimethyl ether (DME) that can also be produced from renewable sources was used as the HRF as a move toward sustainable power generation. The two-cylinder turbocharged diesel engine modified to work in the DME–biogas RCCI (DMB-RCCI) mode was studied under different proportions of methane (45–95%) in biogas since the quality of this fuel can vary depending on the feedstock and production method. Only a narrow range of biogas to DME ratios could be tolerated in this mode at each output without misfire or knock. Detailed experiments were conducted at brake mean effective pressures (BMEPs) of 3 and 5 bar at a speed of 1500 rpm and comparisons were made with the diesel–biogas dual-fuel and diesel–biogas RCCI modes under similar methane flow rates while the proportion of CO2 was varied.

Reactivity Controlled Compression Ignition (RCCI) is a promising, high-efficiency, clean combustion mode for diesel engines. One of the significant limitations of RCCI is its higher unburned hydrocarbon (HC) and carbon monoxide (CO) emissions compared to conventional diesel combustion. After-treatment control of HC and CO emissions is difficult to achieve in RCCI because of lower exhaust gas temperatures associated with the low-temperature combustion (LTC) mode of operation. The present study involves combined experimental and computational fluid dynamic (CFD) investigations to develop the most effective HC and CO control strategy for RCCI. A production light-duty diesel engine is modified to run in RCCI mode by introducing electronic port fuel injection with the replacement of mechanical injectors by the CRDI system. Experimental data were obtained using diesel as HRF (High reactive fuel) and gasoline as LRF (low reactive fuel).

This study experimentally investigates the combustion stability in RCCI engines along with the gaseous (regulated and unregulated) and particle emissions. Multifractal analysis is used to characterize the cyclic combustion variations in the combustion parameters (such as IMEP, CA50, and THR). This analysis aims to investigate the multifractal characteristics of the RCCI combustion mode near the misfiring limit. The investigation is carried out on a modified single-cylinder diesel engine to operate in RCCI combustion mode.The RCCI combustion mode is tested for different diesel injection timing (SOI) at fixed engine speed (1500rpm) and load (1.5 bar BMEP). The particle number characteristics and gaseous emissions are measured using a differential mobility spectrometer (DMS500) and Fourier Transform Infrared Spectroscopy (FTIR) along with Flame Ionizing Detector (FID), respectively.

Substantial effort has been devoted to utilizing homogeneous charge compression ignition (HCCI) to improve thermal efficiency and reduce emission pollutants in internal combustion engines. However, the uncertainty of ignition timing and limited operational range restrict further adoption for the industry. Using the spark-assisted compression ignition (SACI) technique has the advantage of using a spark event to control the combustion process. This study employs a rapid compression machine to characterize the ignition and combustion process of Dimethyl ether (DME) under engine-like background temperature and pressures and combustion regimes, including HCCI, SACI, and knocking onsite. The spark ignition timing was swept to ignite the mixture under various thermodynamic conditions. This investigation demonstrates the presence of four distinct combustion regimes, including detonation, strong end-gas autoignition, mild end-gas autoignition, and HCCI.

Abstract Reactivity-controlled compression ignition (RCCI) engine is an innovative dual-fuel strategy, which uses two fuels with different reactivity and physical properties to achieve low-temperature combustion, resulting in reduced emissions of oxides of nitrogen (NOx), particulate matter, and improved fuel efficiency at part-load engine operating conditions compared to conventional diesel engines. However, RCCI operation at high loads poses challenges due to the premixed nature of RCCI combustion. Furthermore, precise controls of indicated mean effective pressure (IMEP) and CA50 combustion phasing (crank angle corresponding to 50% of cumulative heat release) are crucial for drivability, fuel conversion efficiency, and combustion stability of an RCCI engine.

The influence of engine load and fuel premixing ratio (PMR) on unregulated emission from a methanol-diesel dual-fuel RCCI (MD-RCCI) engine is examined in this study. The study focuses on assessing the adverse effects of unregulated emissions (saturated HC, unsaturated HC, carbonyl compounds, aromatic hydrocarbon, NH3, and SO2) on the health of human beings and the environment. To quantify the effect on the environment, the greenhouse gas potential (GWPs), Eutrophication potential (EP), Acidification potential (AP), and Ozone forming potential (OFP) are calculated and presented. The cancer risk potential (CRP) of the carbonyl compounds (HCHO and CH3CHO) is calculated and presented to see the effect on human health. The results demonstrate that at lower engine load, with an increase in PMR, the OFP and CRP for MD-RCCI operation increase significantly, whereas AP, EP, and GWPs decrease. Additionally, with a rise in the load at a constant PMR, the AP, EP and OFP decrease significantly.

It is a well-known fact that HCCI combustion offers the possibility of achieving high efficiency with low emissions, but with the challenges in combustion control and ability to adjust to changing environmental conditions. To resolve the aforementioned challenges, a pre-chamber induced homogeneous charge compression ignition (PC-HCCI) combustion mode was experimentally tested with aim of providing initial operating boundaries in terms of combustion stability and obtaining initial performance results. The single cylinder engine equipped with active pre-chamber and compression ratio (CR) of 17.5 was fueled by gasoline. The initial experiments were performed at the engine speed of 1600 rpm with intake air temperatures varied from 33°C to 100°C to verify the possibility of achieving the PC-HCCI combustion mode and to compare the achieved engine performance and emission results with both PCSI and pure HCCI combustion modes used as reference cases.

Hydrogen has attracted attention as one of the key fuels for making internal combustion engines carbon neutral. However, the combustion characteristics of hydrogen differ greatly from those of conventionally used hydrocarbons. Therefore, in order to develop next-generation internal combustion engines that operate on hydrogen, it is first necessary to have a thorough understanding of the combustion characteristics of hydrogen. Engines that can take maximum advantage of those characteristics should be developed on the basis of that knowledge. Toward that end, the purpose of this study was to investigate the fundamental combustion characteristics of hydrogen in a test engine. This paper presents the results of an investigation of the effects on low-temperature oxidation reactions and autoignition when hydrogen was blended into dimethyl ether (DME) [1, 2], a gaseous hydrocarbon fuel.

The Homogeneous Charge Compression Ignition (HCCI) combustion eliminates the issues of higher particulate matter and nitrogen oxides emissions that prevail in the traditional compression ignition (CI) combustion mode. The complete replacement of traditional fuels with renewable fuels for internal combustion engines is challenging because significant infrastructure changes in the production and delivery systems are required to ensure renewable fuel availability and economic feasibility. Thus, the use of renewable acetone blended with traditional gasoline has been proposed in the present study to smoothen the transition from the traditional CI to the HCCI engines. HCCI experiments were performed in a light-duty diesel engine at 1500 rpm rated speed. By varying the volumetric proportion of the acetone in the gasoline from 20% to 40%, the HCCI engine load range from 20%-60% was achieved, significantly higher than the limited diesel HCCI load range of 20%-38%.

Abstract TOC

The present research explores the application of biodiesel fuel in a stationary agricultural engine operated under the Homogenous charge compression ignition (HCCI) mode. To achieve HCCI combustion, a fuel vaporizer and a high-pressure port fuel injection system are employed to facilitate rapid evaporation of the biodiesel fuel. The low volatility of biodiesel is one of the significant shortcomings, which makes it inevitable to use a fuel vaporizer at 380oC. Consequently, the charge temperature is high enough to promote advanced auto-ignition. Further, the high reactivity of biodiesel favors early auto-ignition of the charge. Besides, biodiesel exhibits a faster burn rate due to its oxygenated nature. The combined effect of advanced auto-ignition and faster burn rate resulted in a steep rise in the in-cylinder pressures, leading to abnormal combustion above 20% load. Diluting the charge reduces reactivity and intake oxygen concentration, facilitating load extension.

The influence of ethanol volume fraction on the spontaneous ignition of homogeneous premixed gas reformed by non-equilibrium plasma was investigated. The HCCI experiments of the gas was carried out using a Rapid Compression Machine (RCM). The spontaneous ignition process and reforming process were numerically investigated by reaction simulation in OD. A simplified model was proposed to explain the influence of the reforming of the gas with different ethanol volume fractions, and the model was validated. These results indicate that the influence of the reforming on ignition delay of cool flame is almost irrespective of the ethanol volume fractions.

The autoignition chemistry of fuels depends on the pressure, temperature, and time history that the fuel-air mixture experiences during the compression stroke. While piezoelectric pressure transducers offer excellent means of pressure measurement, temperature measurements are not commonly available and must be estimated. Even if the pressure and temperature at the intake and exhaust ports are measured, the residual gas fraction (RGF) within the combustion chamber requires estimation and greatly impacts the temperature of the fresh charge at intake valve closing. This work replaced the standard D1 Detonation Pickup of a CFR engine with a rapid sampling valve to allow for in-cylinder gas sampling at defined crank-angle times during the compression stroke. The extracted cylinder contents were captured in an emissions sample bag and its composition was subsequently analyzed in an AVL i60 emissions bench.

A transition to sustainable energy sources, carbon- free/neutral energy carriers and efficient combustion technologies is intensively discussed as a key pathway in achieving a greener, more secure energy future. In particular, enhancement of internal combustion engine (ICE) performance using promising alternative carbon- neutral propellants, waste heat recovery (WHR) and state-of-the-art combustion methods has gained high research attention. Polyoxymethylene dimethyl ethers (PODEn, OMEn), well-suited for compression-ignition (CI) combustion, arouse strong interest as potentially sustainable and cleaner alternatives to diesel fuel. This study reports for the first-time numerically examined combustion performance characteristics of reforming- controlled compression ignition (RefCCI) ICE engine, managed by mixing of polyoxymethylene dimethyl ether 1 (PODE1) and its hydrogen-rich reforming products (PODE1-reformate) obtained through thermo- chemical recuperation.

Homogeneous charge compression ignition (HCCI) combustion is promising for not only high thermal efficiency but also reducing nitrogen oxides (NOx) and PM simultaneously. However, the operational range of the HCCI combustion is limited because of some issues, such as poor control of ignition timing and knocking by the excessive rate of pressure rise. In this study, a new combustion system based on the HCCI combustion process is proposed based on the authors' previous experimental work. This combustion system has a divided combustion chamber of two parts, one is small and the other is large. The most significant feature is the small chamber inside the piston. At first, combustion takes place in the small chamber, and then the burned gas is ejected into the large chamber to ignite the mixture in the large chamber.

With the aim to further reduce and limit pollutant emissions and fuel consumption towards carbon neutrality, researchers and automotive manufacturers have been studying new combustion technologies, such as low temperature combustions, which provide an efficient combustion with low pollutant emissions. Despite innovative combustion techniques, such as Homogeneous charge compression ignition (HCCI) and Gasoline compression ignition (GCI), proved to reduce pollutant emissions and increase efficiency of internal combustion engines, their large-scale deployment has been limited by problems in combustion management and stability. In fact, the challenge related to these innovative combustion techniques consists in the development of new control strategies and new calibration methodologies, which allow to limit their combustion instability.

In recent years, there has been a need to reduce CO2 emissions from internal combustion engines in order to achieve an energy-saving and low-carbon society. Against this backdrop, the authors have focused attention on Homogeneous Charge Compression Ignition (HCCI) combustion that achieves both high efficiency and clean emissions. With HCCI combustion, a premixed mixture of fuel and air is supplied to the cylinder and autoignited by piston compression to drive the engine. Autoignition makes it possible to operate the engine at a high compression ratio, enabling the HCCI combustion system to attain high efficiency. However, HCCI combustion also has some major unresolved issues. Two principal issues that can be cited are ignition timing control for igniting the mixture at the proper time and assurance of suitable combustion conditions following ignition to prevent incomplete combustion and knocking.

As a technology to reduce the heat loss of engines, heat insulation coating to the surface of combustion chamber has been received a lot of attention. In order to maximize the thermal efficiency improvements by the technology, it is important to clarify the location where heat insulation coating can reduce heat loss more effectively, considering the impact on abnormal combustion etc. In this study, transient behavior of wall heat flux distribution on the piston was analyzed using 3D Computational Fluid Dynamics (CFD) for three combustion modes (spark ignition combustion (SI), homogenous charge compression Ignition (HCCI) and spark controlled compression ignition (SPCCI)).

Ammonia, which is one of the most produced inorganic chemicals worldwide, has gained significant attention in recent years as a carbon-free fuel due to its significant energy density in maritime and power plant applications. This fuel offers several advantages including low production costs and being safe for storage and transport. Reactivity controlled compression ignition (RCCI) combustion mode is considered as a promising strategy reducing the level of nitrogen oxides (NOx) emissions and particulate matters (PM) in internal combustion engines (ICEs) due to the lower combustion temperatures and charge homogeneity. Ammonia-based RCCI combustion strategy can offer a simultaneous reduction of CO2 and NOx. In this study, a RCCI engine fuelled by ammonia and diesel is numerically simulated considering chemical reactions kinetics mechanism of the combustion.

Biogas is a gas resulting from biomass, with a volumetric content of methane (CH4) usually ranging between 50% and 70%, and carbon dioxide (CO2) content between 30% and 50%; it can also contain hydrogen (H2) depending on the feedstock. Biogas is generally used to generate electricity or produce heat in cogeneration system. Due to its good efficiency through the rapid combustion and lean air-fuel mixture, Homogeneous Charge Compression Ignition (HCCI) engine is a good candidate for such application. However, the engine load must be kept low to contain the high-pressure gradients caused by the simultaneous premixed combustion of the entire in-cylinder charge. The homogenous charge promotes low particulate emissions, and the dilution helps in containing maximum in-cylinder temperature, hence reducing nitrogen oxide emissions. However, HC and CO levels are in general higher than in SI combustion.