Refine Your Search

Date

Date

Truck and Bus Wheel Committee Trailers

Search Results

Viewing 1 to 20 of 31
12Next >Last >>
Sort by published
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims
2021-05-06
CURRENT
J1095_202105
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters ranging from 165.1 to 335.0 mm (6.500 to 13.189 inches). It is up to each hub and/or wheel for demountable rims manufacturer to determine the appropriate test method, accelerated load factor and cycle life requirements applicable to obtain satisfactory service life for a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters as necessary to ensure satisfactory service life for the intended application. It should be noted that this test procedure focuses on fatigue resulting from vehicle loading and cornering forces.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions - Truck and Bus
2020-02-13
CURRENT
J2475_202002
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, spindle threads, bearing cones, bearing spacer, seal, and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2019-10-07
CURRENT
J2535_201910
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

ABS Exciter Ring Location Standardization
2019-02-11
HISTORICAL
J1730_201902
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a FF b FL c FC d FH e L f R g U h W j N k P
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2018-08-08
HISTORICAL
J1842_201808
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims
2016-06-30
HISTORICAL
J1095_201606
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.500 to 13.189 in). It is up to each hub and/or wheel for demountable rims manufacturer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.
Standard

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging
2015-11-19
CURRENT
J2224_201511
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. 1.1 Purpose The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
Standard

Disc Wheel Hub/Spoke Wheel and Axle Interface Dimensions - Truck and Bus
2014-02-03
HISTORICAL
J1842_201402
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2013-02-11
HISTORICAL
J2535_201302
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

ABS Exciter Ring Location Standardization
2012-03-15
HISTORICAL
J1730_201203
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a FF b FL c FC d FH e L f R g U h W j N k P
Standard

Fatigue Test Procedures: Hubs and Wheels for Demountable Rims
2009-10-12
HISTORICAL
J1095_200910
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of wheels for demountable rims and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or wheel for demountable rims developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or wheel for demountable rims developer to modify other parameters to obtain satisfactory service life.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus
2008-08-22
HISTORICAL
J2475_200808
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.
Standard

Setting Preload in Heavy-Duty Wheel Bearings
2006-12-06
HISTORICAL
J2535_200612
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway, disc wheel / outboard drum brake applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

ABS Excitor Ring Location Standardization
2004-07-27
HISTORICAL
J1730_200407
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of the hub on the following axle designations. a FF b FL c L d R e U f W g N h P
Standard

Spoke Wheels and Hub Fatigue Test Procedures
2003-03-07
HISTORICAL
J1095_200303
This SAE Recommended Practice provides uniform laboratory procedures for fatigue testing of spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles. The hubs included have bolt circle diameters from 165.1 to 335.0 mm (6.50 to 13.19 in). It is up to each hub and/or spoke wheel developer to determine what test method, accelerated load factor and cycle life requirements are applicable to obtain satisfactory service life in a given application. When deviations from the procedures recommended herein are made, it is the responsibility of the hub and/or spoke wheel developer to modify other parameters to obtain satisfactory service life.
12Next >Last >>
X