Search Results

This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.

This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a Scrapers as defined in ISO 7133. b Dozers as described in ISO 6747. c Loaders as described in ISO 7131. d Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.

This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters. NOTE—For some heavy-duty applications, cross sections with larger blunts, greater bevel angles, and larger bolt holes may be required.

This standard is for cutting edge sections typically used in earthmoving machinery defined in SAE J1507: a Tractor - Scrapers as defined in SAE J728. b Dozers as described in SAE J729 and J173. c Loaders as described in SAE J731. d Graders as described in SAE J870. Hole spacing is defined for dozers and scrapers in J737 and graders in J739. Hole conformation is defined in J740.

This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.

This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.

This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.

This standard is for cutting edge sections typically used in earthmoving machinery defined in SAE J1507: a Tractor - Scrapers as defined in SAE J728. b Dozers as described in SAE J729 and J173. c Loaders as described in SAE J731. d Graders as described in SAE J870. Hole spacing is defined for dozers and scrapers in J737 and graders in J739. Hole conformation is defined in J740.

This SAE Standard applies to off-road self-propelled construction, forestry, and industrial machines as listed in categories 1, 2, and 4 of SAE J1116.

This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. See Figures 1 to 3.)

This SAE Standard applies to off-road self-propelled construction, forestry, and industrial machines as listed in categories 1, 2, and 4 of SAE J1116.

This code applies to all types of self-propelled machinery. It covers five methods of determination as follows: Suspension Method Null Point Method Platform Support Reaction Method Reaction Method Balance Method