Search Results

This document gives specific and measurable design requirements to be applied at a design review prior to tooling. The specification is formatted as a checklist to aid in its use. The requirements do not apply in all situations so engineering judgment must be used. This is a specification for design; applicable performance specifications (USCAR-2, etc.) must still be performed. Specific requirements in this document are grouped by component using a prefix as shown in Table 1 and are numbered by an item number following the prefix.

A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications.

This standard lists variables that shall be investigated and reported as an initial investigation into new or revised surface finishes intended for use on fasteners. This standard provides instruction for producing a final report that will be used to determine if further investigation of a surface finish is justified. Further investigation may include tests and evaluations specific to an individual OEM prior to introduction/approval of the surface finish. The final report shall include the results, observations, and conclusions for all of the variables. The final report may be made up of several individual reports covering each variable. In all cases the laboratory performing the test, the test date and the report approver shall be included in the final report.

This standard outlines the conditions that enhance the risk of hydrogen embrittlement of steel and define the relief procedures required to minimize the risk of hydrogen embrittlement. It is intended to control the process.

This specification defines test methods and performance criteria for evaluating ultrasonically welded wire-to-terminal metallurgical bonds. The examples used are specific to the linear weld type of process equipment. USCAR-38 is not applicable for “Splice Welding”. The specification is applicable to wire-on-pad configurations with a typical weld shown in Figure 1. This test specification subjects parts under test to environmental exposures to simulate a lifetime of field exposure for a road vehicle. Exposures called-out in this specification include Thermal Shock, Temperature Humidity Cycling and mechanical abuse. This test specification is intended to evaluate the strength and performance of the interface between wires to an electrical terminal. Validation of the performance of the Terminal is a separate task and can be accomplished using a component validation test such as SAE/USCAR-2, which evaluates whether the entire connection system is acceptable.

This document describes the design and assembly force guidelines for conventional shipping caps, torque caps, and body plugs. All possible design and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the-shelf” design, always consult the responsible Ergonomics Department.

This document describes the assessment methods and physical requirements associated with the manual handling of carts and dollies, specific to material handling systems. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the shelf” design, always consult the responsible Ergonomics Department. Force guidelines were primarily developed referencing the push/pull psychophysical Snook data contained in A Guide to Manual Materials Handling (second edition) by Mital, Nicholson and Ayoub (NY: Taylor & Francis, 1997). The force guidelines accommodate 75% of female capabilities and 99% of male capabilities. Factors that were included in the established guideline include: push / pull distances, vertical hand height, horizontal hand height, frequency and wheel / castor alignment and load rating. These factors were used to develop a conservative force guideline.

This document describes the design, assessment methods and physical requirements associated with material handling systems. This would include, but not limited to manual dollies, small lot systems and kitting. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the shelf” design, always consult the responsible Ergonomics Department.

This standard is intended to cover cigar or cigarette lighters as well as power outlets based on the form and dimensions of the cigar lighter. This standard is a full performance specification, it includes dimensional and operational parameters as well as performance characteristics which must be met when submitting a cigar lighter assembly or power outlet assembly for production approval. This standard constitutes an acceptance specification for a surface mounted, front-loaded cigar lighter or power outlet.

This standard outlines the conditions that enhance the risk of hydrogen embrittlement of steel and define the relief procedures required to minimize the risk of hydrogen embrittlement. It is intended to control the process.

This standard outlines the conditions that enhance the risk of hydrogen embrittlement of steel and define the relief procedures required to minimize the risk of hydrogen embrittlement. It is intended to control the process.

A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications.

This standard lists variables that shall be investigated and reported as an initial investigation into new or revised surface finishes intended for use on fasteners. This standard provides instruction for producing a final report that will be used to determine if further investigation of a surface finish is justified. Further investigation may include tests and evaluations specific to an individual OEM prior to introduction/approval of the surface finish. The final report shall include the results, observations, and conclusions for all of the variables. The final report may be made up of several individual reports covering each variable. In all cases the laboratory performing the test, the test date and the report approver shall be included in the final report.

This specification establishes the design, performance, and validation requirements for the initiator assembly used in airbag modules, seatbelt pretensioners and/or any other Electro-Explosive Devices (EED).

This standard is intended to cover cigar or cigarette lighters as well as power outlets based on the form and dimensions of the cigar lighter. This standard is a full performance specification, it includes dimensional and operational parameters as well as performance characteristics which must be met when submitting a cigar lighter assembly or power outlet assembly for production approval. This standard constitutes an acceptance specification for a surface mounted, front-loaded cigar lighter or power outlet.