Refine Your Search

Date

Date

Topic

Topic

Vehicle dynamics Pressure Environment Design Engineering and Styling Materials, Processes and Parts Council Particulate matter (PM)

Search Results

Viewing 1 to 20 of 47
123Next >Last >>
Sort by published
Standard

Abrasion Resistance Testing - Vehicle Exterior Graphics and Pin Striping
2021-01-07
CURRENT
J1847_202101
This SAE Recommended Practice applies to the abrasion resistance testing of decorative tapes, graphics, and pin striping. It may also have relevance to certain vehicle labels and plastic wood grain film. The resistance to abrasive damage is judged qualitatively by its effect on the legibility, pattern, and color of the graphic marking. This recommended practice is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering the use of this recommended practice.
Standard

Induction Cure Test for Metal Bonding Adhesives
2021-01-07
CURRENT
J1851_202101
This SAE Recommended Practice defines a procedure for determining the adhesion strength characteristics of heat-cured metal bonding adhesives subjected to induction heating.
Standard

Accelerated Environmental Testing for Bonded Automotive Assemblies
2021-01-07
CURRENT
J2100_202101
This SAE Recommended Practice defines conditions to which bonded assemblies can be exposed to simulate environmental aging. These recommendations are generally based on existing Original Equipment Manufacturer requirements at this time. (Environmental specifications used for this proposal were from General Motors, Ford, and Chrysler.) The substrate type, dimension, and number are described by the standard for materials being tested and should include control specimens which receive no environmental aging.
Standard

Peel Adhesion Test for Glass to Elastomeric Material for Automotive Glass Encapsulation
2021-01-07
CURRENT
J1907_202101
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass. This test method suggests that elastomeric material of less than 172 mpa modulus be used as the encapsulating material. The present practice of encapsulating automotive glass is described as molded-in-place elastomeric material onto the outer edge of the glass using thermoplastic or thermosetting material that quickly sets in the mold. The glass is removed from the mold with the cured elastomeric material bonded to the perimeter of the glass. This encapsulated glass module can now be bonded with a sealant adhesive into the body opening of a vehicle.
Standard

Coach Joint Fracture Test
2021-01-07
CURRENT
J1863_202101
This SAE Recommended Practice defines a procedure for determining the cleavage strength of an adhesive used for bonding automotive oily metal substrates.
Standard

Method of Viscosity Test for Automotive Type Adhesives, Sealers, and Deadeners
2021-01-07
CURRENT
J1524_202101
This SAE Recommended Practice contains a series of test methods for use in measuring the viscosity of automotive-type adhesives, sealers, and deadeners. The test methods which are contained in this document are as follows: 1.1 Brookfield® Method 1.2 Castor-Severs Rheometer or Pressure Flowmeter 1.3 Penetrometer 1.4 Capillary Rheometer 1.5 Plate Rheometers
Standard

Technical Report on Low Cycle Fatigue Properties Ferrous and Non-Ferrous Materials
2018-08-24
CURRENT
J1099_201808
Information that provides design guidance in avoiding fatigue failures is outlined in this SAE Information Report. Of necessity, this report is brief, but it does provide a basis for approaching complex fatigue problems. Information presented here can be used in preliminary design estimates of fatigue life, the selection of materials and the analysis of service load and/or strain data. The data presented are for the “low cycle” or strain-controlled methods for predicting fatigue behavior. Note that these methods may not be appropriate for materials with internal defects, such as cast irons, which exhibit different tension and compression stress-strain behavior.
Standard

Elastomeric Bushing "TRAC" Application Code
2017-02-09
CURRENT
J1883_201702
The bushing "TRAC" code is intended to be a tool that will aid in the definition of the geometric environment for the test, or use, of an elastomeric bushing.
Standard

Helical Springs: Specification Check Lists
2016-08-02
CURRENT
J1122_201608
The following SAE Recommended Practice furnishes sample forms for helical compression, extension and torsion springs to provide a uniform method for specifying design information. It is not necessary to fill in all the data, but sufficient information must be supplied to fully describe the part and to satisfy the requirements of its application. For detailed information, see “Design and Application of Helical and Spiral Springs - SAE HS 795”, also “Helical Compression and Extension Spring Terminology - SAE J1121”. Both of these documents use SI (metric) Units in accordance with the provisions of SAE TSB 003, as does SAE J1122. Here, however, the U.S. Customary Units (in, lb, psi) have been added in parentheses after each SI Unit for the convenience of the user who must furnish specifications on a project where all requirements are listed in non-metric terms.
Standard

Leaf Springs For Motor Vehicle Suspension - Made to Metric Units
2016-04-05
CURRENT
J1123_201604
NOTE—For leaf springs made to customary U.S. units, see SAE J510. This SAE Standard is limited to concise specifications promoting an adequate understanding between spring maker and spring user on all practical requirements in the finished spring. The basic concepts for the spring design and for many of the details have been fully dealt with in HS-J788.
Standard

Undervehicle Coupon Corrosion Tests
2016-04-05
CURRENT
J1293_201604
This document is a road test procedure for comparing the corrosion resistance of both coated and uncoated sheet steels in an undervehicle deicing salt environment.
Standard

Guidelines for Laboratory Cyclic Corrosion Test Procedures for Painted Automotive Parts
2016-04-05
CURRENT
J1563_201604
These guidelines are intended for those engineers and scientists who evaluate the corrosion performance of painted automotive parts in laboratory cyclic tests. The guidelines are intended to help ensure that the results of the tests can be used to reach conclusions concerning the variables under study without being confounded by the test procedure itself. The guidelines also serve as a means to assist users of this type of test in obtaining good inter-laboratory agreement of results.
Standard

Proving Ground Vehicle Corrosion Testing
2016-04-05
CURRENT
J1950_201604
The facilities used by domestic automotive manufacturers to provide accelerated corrosion aging of complete vehicles are described in general. The types of vehicles tested, general test methodology, and techniques used to determine test-to-field correlation are discussed. The different procedures used throughout the industry produce different results on various vehicle coatings, components, and systems. The key to successful interpretation of test results is a thorough understanding of the corrosion mechanisms involved and the effects of test limitations on these mechanisms.
123Next >Last >>
X