Search Results

Because the transportation industry uses fossil fuels as much as 1/4 of the total, CO2 emission from transport sector should be reduced. Therefore, carbon neutral (CN) fuel has been attracted attention. However, hydrogen and ammonia have low energy density and are difficult to be stored and transported. In this study, synfuel produced by Fischer-Tropsch (FT) reaction. This fuel is produced with carbon dioxide absorbed from the direct air capture and electricity derived from renewable energy, so it is possible to achieve CN. However, FT fuel tends to have less aromatics and a higher cetane number than diesel fuel. Therefore, excessive early ignition occurs at low speed and low load in application to diesel engine. The purpose of this study is to suppress early ignition by controlling the amount of air flowing into the cylinder. The numerical results showed that the ignition timing and combustion could be controlled using Miller cycle by late intake valve closing (LIVC).

Research on alternative fuels is necessary to reduce CO2 emissions. Hydrotreated Vegetable Oil (HVO) of light fuel physically improves spray and combustion characteristics. Fatty Acid Methyl Ester (FAME) is an oxygenated fuel and its combustion characteristics are chemically improved, although its spray characteristics such as penetration and atomization are deteriorated. The purpose of this study is to understand the effects of blending HVO, which has carbon neutral (CN) characteristics, with FAME, which also has CN characteristics, on spray and combustion characteristics, and to further improve emission such as THC and Smoke. This report presents the effect of the combination of improved spray characteristics and oxygenated fuel on emissions. Spray characteristics such as penetration, spray angle and spray volume were investigated by shadowgraph photography.

To reduce carbon dioxide emissions, the use of vehicles operating on electrification technology, such as plug-in hybrid electric vehicles (PHEVs) and electric vehicles (EVs) is rapidly increasing. A similar trend also exists in the field of heavy-duty vehicles, such as trucks and buses. When evaluating—via the certification test method—the fuel efficiency, electricity efficiency, and exhaust gas emission of heavy-duty vehicles that have many batteries, the powertrain, including the batteries, is modeled and investigated. However, such modeling is difficult because batteries deteriorate, and the ambient temperature fluctuates during vehicle operation. To resolve this issue, we developed a new evaluation method that enables real-time cooperative control of actual batteries and hardware-in-the-loop simulation (HILS).

From the perspective of improving the atmospheric environment, evaluating the fuel efficiency and exhaust gas emissions when using actual vehicles on real roads is necessary. Passenger vehicles apply RDE (real driving emission) test. However, unlike passenger vehicles, there are many types and models of heavy-duty vehicles; thus, evaluating all of these types using real driving emission tests is difficult. Therefore, we investigated the possibility of an alternative evaluation of heavy-duty vehicle based on a simulation method that uses a vehicle model for part of the evaluation. This alternative evaluation method is a combination of the “engine HILS (hardware-in-the-loop simulation)” method, developed in previous studies and can perform tests based on vehicle speed and driving wind that is reproduced in the engine bench to appropriately cool the engine and various devices.

Fuel consumption and exhaust gas emission regulations are being tightened around the world year by year. Electric vehicles are needed to reduce carbon dioxide emissions. Especially, Plug-in hybrid heavy-duty vehicles (PHEVs) are expected to become widespread. PHEVs enable all-electric modes, as well as hybrid modes, using both engines and electric motors, but the control system significantly affects the characteristics of fuel consumption and gas emission. In this study, we used new testing machine (we call extended HILS) to analyze the fuel consumption and gas emission for different plug-in hybrid control systems and investigated the optimal control method for PHEVs.

Fuel design concept has been proposed for low emission and combustion control in engine systems. In this concept, the multicomponent fuels, which are mixed with a high volatility fuel (gasoline or gaseous fuel components) and a low volatility fuel (gas oil or fuel oil components), are used for artificial control of fuel properties. In addition, these multicomponent fuels can easily lead to flash boiling which promote atomization and vaporization in the spray process. In order to understand atomization and vaporization process of multicomponent fuels in detail, the model for flash boiling spray of multicomponent fuel have been constructed and implemented into KIVA3V rel.2. This model considers the detailed physical properties and evaporation process of multicomponent fuel and the bubble nucleation, growth and disruption in a nozzle orifice and injected fuel droplets.

Bio-hydro fined diesel (BHD) oil is known as a second generation oil made from bio hydro finning process. Biodiesel in the first generation is made from transesterification process and it has several disadvantages such as high density and increased the viscosity that can cause operational problems because can make some deposits in the engine. To overcome this, the second generation process of biodiesel has been modified from the first generation oil. BHD is made from the waste cooking oil by using the hydro finning process without the trans-esterification process. The results of BHD oil has nearly the same with diesel oil. BHD oil has low viscosity and high oxidation stability. Therefore, BHD oil can be used in the diesel engine without making any modifications in the engine. In this study, the comparison of performance and emissions characteristics from BHD oil, waste cooking oil, and diesel oil are investigated.

Fuel consumption rate (fuel economy) and exhaust gas emission regulations are being tightened around the world year by year. In Europe, the real driving emission (RDE) method for evaluating exhaust gas emitted from road-going vehicles was introduced after September 2017 for new types of light/medium-duty vehicles, in addition to the chassis dynamometer test using the worldwide harmonized light vehicles test procedure (WLTP). Further, the worldwide harmonized heavy-duty certification (WHDC) method was introduced after 2016 as an exhaust gas emission test method for heavy-duty vehicles. In each evaluation, the tests of vehicles and engines are initiated from cold states. Heavy-duty hybrid vehicles are evaluated using the vehicle simulation method. For example, the power characteristics of a engine model is obtained during engine warm operation. Therefore, various performances during cold start cannot be precisely evaluated by using simulator.

Around the world, fuel economy and emission regulations for vehicles have become increasingly stringent year by year. In Europe, the real driving emission (RDE) testing was introduced for evaluating the emission at driving the road-going vehicles after September 2017. In order to effiency produce the actual vehicles, Each automobile manufacturer introduce the “Hardware In the Loop Simulator” (HILS) and “Engine In the Loop Simulator” (which is called the EILS or the extended HILS [1, 2]), which is combined with HILS and an actual engine. However, if the driver model used in the vehicle simulation (HILS, extended HILS) does not correctly simulate actual human driving behaviors, the model vehicle performances will differ from the actual vehicle performance. The fuel economy and emission characteristics are affected by the differences of the driver model control logic during the execution of vehicle simulation.

In order to improve the fuel economy of the heavy duty trucks at a highway driving condition, the heavy duty hybrid trucks with new type of hybrid electric assist engine system were proposed at the previous report. The new system consists of a downsizing diesel engine with a two-stage charging structure, which has an electric supercharger with bypass circuit and a conventional turbocharger, the hybrid electric motor and the small-capacity battery. The electric power consumption of an electric supercharger is equivalent to the amount of the regeneration power produced during high-speed driving where the opportunity of the regeneration is small. In this report, an electric supercharger for the heavy duty hybrid truck was produced experimentally. First, the engine performance and exhaust emissions were investigated using the 4 cylinder diesel engine equipped with an electric supercharger.

In the conventional approval test method of fuel consumption for heavy-duty diesel vehicles currently in use in Japan, the fuel consumption under the transient test cycle is calculated by integrating the instantaneous fuel consumption rate referred from a look-up table of fuel consumptions measured under the steady state conditions of the engine. Therefore, the transient engine performance is not considered in this conventional method. In this study, a highly accurate test method for fuel consumption in which the map-based fuel consumption rate is corrected using the transient characteristics of individual engines was developed. The method and its applicability for a heavy-duty diesel engine that complied with the Japanese 2009 emission regulation were validated.

Next-generation vehicles which include Electric Vehicles and Hybrid Electric Vehicles are studied and expected to reduce carbon dioxide emissions. The number of small delivery hybrid trucks has increased in the commercial vehicle class. The engine load of a commercial hybrid truck is reduced by using an electric motor. Fuel economy of the hybrid truck is improved with the assist. On the other hand, exhaust-gas temperature is decreased, and it has a negative effect on the purification performance of aftertreatment system. In this report, the fuel performance and emission gas characteristics of marketed small hybrid trucks were surveyed using the chassis dynamometer test system.

Widespread use of biofuels for automobiles would greatly reduce CO2 emissions and increase resource recycling, contributing to global environmental conservation. In fact, activities for expanding the production and utilization of biofuels are already proceeding throughout the world. For diesel vehicles, generally, fatty acid methyl ester (FAME) made from vegetable oils is used as a biodiesel. In recent years, hydrotreated vegetable oil (HVO) has also become increasingly popular. In addition, biomass to liquid (BTL) fuel, which can be made from any kinds of biomass by gasification and Fischer-Tropsch process, is expected to be commercialized in the future. On the other hand, emission regulations in each country have been tightened year by year. In accordance with this, diesel engines have complied with the regulations with advanced technologies such as common-rail fuel injection system, high pressure turbocharger, EGR and aftertreatment system.

Next-generation vehicles which include Electric Vehicles (EV) and Hybrid Electric Vehicles (HEV) are researched and expected to reduce carbon dioxide (CO2) emissions in the future. In the national new-car sales in 2012 of Japan, the total sales of hybrid vehicles kept 26.5% share. In the field of passenger cars, this share was 29.7%. And, this share rose about four times compared to that of 2008 [1]. Also, small delivery hybrid trucks are increased in the commercial vehicle class. Fuel economy of hybrid trucks in the catalog specifications is relatively better than that of the diesel tracks which have no hybrid systems. Nevertheless, hybrid trucks' users report that advantages of fuel economy of hybrid trucks at the real traffic driving conditions are small.

Next-generation vehicles which include Electric Vehicles (EV) and Hybrid Electric Vehicles (HEV) are researched and expected to reduce CO2 emissions in the future. Generally, the main factor to support high efficiency of EV and HEV is the idle stop, motor assistance and regenerative braking. The vehicle mechanism of HEV is complex, compared with conventional internal combustion engine vehicle. Certification test method of gas emissions and fuel consumption is used driving mode, which is currently reflecting the typical driving conditions in the market. And driving mode of certification test is established focusing on the reproducibility of driving by conventional internal combustion engine vehicles. It is necessary to consider that the driving mode for the vehicle used regenerative energy is reflected correctly. And high accuracy certification test method for next generation HEVs is necessary in order to evaluate exhaust gas and fuel economy.

The use of biofuel is essential for the reduction of greenhouse gas emission. This study highlights the use of biodiesel as a means of reducing greenhouse gas emission from the diesel engine of heavy-duty vehicles. Biodiesel is fatty acid methyl ester (FAME) obtained through ester exchange reaction by adding methanol to oil, such as rapeseed oil, soybean oil, palm oil, etc. The CO2 emission from combustion of biodiesel is defined to be equivalent to the CO2 volume absorbed by its raw materials or plants in their course of growth. On the other hand, however, operation of diesel engine with biodiesel is known to increase the NOx emission when compared with that with conventional diesel fuel. Then suppressing this NOx increase is regarded as a critical issue. This paper consists of two parts: comprehending the factors of NOx emission increase and improving this emission performance in a diesel engine fuelled with biodiesel.

Ignition, combustion and emissions characteristics of dual-component fuel spray were examined for ranges of injection timing and intake-air oxygen concentration. Fuels used were binary mixtures of gasoline-like component i-octane (cetane number 12, boiling point 372 K) and diesel fuel-like component n-tridecane (cetane number 88, boiling point 510 K). Mass fraction of i-octane was also changed as the experimental variable. The experimental study was carried out in a single cylinder compression ignition engine equipped with a common-rail injection system and an exhaust gas recirculation system. The results demonstrated that the increase of the i-octane mass fraction with optimizations of injection timing and intake oxygen concentration reduced pressure rise rate and soot and NOx emissions without deterioration of indicated thermal efficiency.

At interurban transportation, improvement of fuel economy of hybrid electric heavy-duty diesel vehicles, which assist drive-axle by using regeneration energy, is minimum, compared to heavy-duty diesel vehicles. One of the factors is that hybrid electric heavy-duty vehicles are not able to balance regeneration energy (input) and power energy (output) at high speed driving. One reason is not opportunity to operate of braking at high speed driving for the heavy-duty vehicle. In this research, we focus on the method used for the battery energy, and propose a new concept of hybrid electric system to efficiently utilize battery energy. That system consists of electrical booster for supercharging intake air into engine cylinder. We have confirmed the feasibility of the electric system of a new HEV concept by using the simulation I created.

Utilization of biofuels to vehicles is attracting attention globally from viewpoints of preventing global warming, effectively utilizing the resources, and achieving the local invigoration. Representative examples are bioethanol and biodiesel. This study highlights biodiesel and hydrotreated vegetable oil (HVO) in view of reducing greenhouse gas emission from heavy-duty diesel vehicles. Biodiesel is FAME obtained through ester exchange reaction by adding methanol to oil, such as rapeseed oil, soybean oil, palm oil, etc. As already reported, FAME has fuel properties different from conventional diesel fuel, resulting in about 10% increase in NOx emission [1],[2],[3]. Suppression of such increase in the NOx emission during operating with biodiesel requires adjustment of the combustion control technology, such as fuel injection control and EGR, to the use of biodiesel.

The use of biofuel is essential for the reduction of greenhouse gas emission. This paper highlights the use of biodiesel as a means of reducing greenhouse gas emission from the diesel engine of heavy-duty vehicles. Biodiesel is fatty acid methyl ester (FAME) obtained through ester exchange reaction by adding methanol to oil, such as rapeseed oil, soybean oil, palm oil, etc. The CO₂ emission from combustion of biodiesel is defined to be equivalent to the CO₂ volume absorbed by its raw materials or plants in their course of growth. On the other hand, however, biodiesel is known to increase the NOx emission when compared with operating with conventional diesel fuel, then suppressing this increase is regarded as a critical issue. This study is intended to identify the fuel properties of biodiesel free from increase in the NOx emission.