Search Results

A detailed understanding of the various factors affecting the trends in gross-indicated thermal efficiency with changes in key operating parameters has been carried out, applied to a one-liter displacement single-cylinder boosted Low-Temperature Gasoline Combustion (LTGC) engine. This work systematically investigates how the supplied fuel energy splits into the following four energy pathways: gross-indicated thermal efficiency, combustion inefficiency, heat transfer and exhaust losses, and how this split changes with operating conditions. Additional analysis is performed to determine the influence of variations in the ratio of specific heat capacities (γ) and the effective expansion ratio, related to the combustion-phasing retard (CA50), on the energy split. Heat transfer and exhaust losses are computed using multiple standard cycle analysis techniques. The various methods are evaluated in order to validate the trends.

This study systematically investigates the effects of various engine operating parameters on the thermal efficiency of a boosted HCCI engine, and the potential of E10 to extend the high-load limit beyond that obtained with conventional gasoline. Understanding how these parameters can be adjusted and the trade-offs involved is critical for optimizing engine operation and for determining the highest efficiencies for a given engine geometry. Data were acquired in a 0.98 liter, single-cylinder HCCI research engine with a compression-ratio of 14:1, and the engine facility was configured to allow precise control over the relevant operating parameters. The study focuses on boosted operation with intake pressures (Pin) ≥ 2 bar, but some data for Pin < 2 bar are also presented. Two fuels are considered: 1) an 87-octane gasoline, and 2) E10 (10% ethanol in this same gasoline) which has a lower autoignition reactivity for boosted operation.

This work explores the potential of partial fuel stratification to smooth HCCI heat-release rates at high load. A combination of engine experiments and multi-zone chemical-kinetics modeling was used for this. The term “partial” is introduced to emphasize that care is taken to supply fuel to all parts of the in-cylinder charge, which is essential for reaching high power output. It was found that partial fuel stratification offers good potential to achieve a staged combustion event with reduced pressure-rise rates. Therefore, partial fuel stratification has the potential to increase the high-load limits for HCCI/SCCI operation. However, for the technique to be effective the crank-angle phasing of the “hot” ignition has to be sensitive to the local ϕ. Sufficient sensitivity was observed only for fuel blends that exhibit low-temperature heat release (like diesel fuel).

Chemiluminescence imaging has been applied to investigate the naturally occurring charge stratification in an HCCI engine. This stratification slows the pressure-rise rate (PRR) during combustion, making it critical to the high-load operating limit of these engines. Experiments were conducted in a single-cylinder HCCI engine modified with windows in the combustion chamber for optical access. Using this engine, chemiluminescence images were obtained from three different view angles. These included both single-shot images with intensified CCD cameras and high-speed (20kHz) sequences with an intensified CMOS video camera. The engine was fueled with iso-octane, which has been shown to be a reasonable surrogate for gasoline and exhibits only single-stage ignition at these naturally aspirated conditions. The chemiluminescence images show that the HCCI combustion is not homogeneous but has a strong turbulent structure even when the fuel and air are fully premixed prior to intake.

Combustion phasing is one important issue that must be addressed for HCCI operation. The intake temperature can be adjusted to achieve ignition at the desired crank angle. However, heat-transfer during induction will make the effective intake temperature different from the temperature measured in the runner. Also, depending on the engine speed and port configuration, dynamic flow effects cause various degrees of charge heating. Additionally, residuals from the previous cycle can have significant influence on the charge temperature at the beginning of the compression stroke. Finally, direct injection of fuel will influence the charge temperature since heat is needed for vaporization. This study investigates these effects in a systematic manner with a combination of experiment and cycle simulation using WAVE from Ricardo.

A combined experimental and modeling study has been conducted to investigate the sources of CO and HC emissions (and the associated combustion inefficiencies) at low-loads. Engine performance and emissions were evaluated as fueling was reduced from knocking conditions to very low loads (ϕ = 0.28 - 0.04) for a variety of operating conditions, including: various intake temperatures, engine speeds, compression ratios, and a comparison of fully premixed and GDI (gasoline-type direct injection) fueling. The experiments were conducted in a single-cylinder engine (0.98 liters) using iso-octane as the fuel. Comparative computations were made using a single-zone model with the full chemistry mechanisms for iso-octane, to determine the expected behavior of the bulk-gases for the limiting case of no heat transfer, crevices, or charge inhomogeneities.

Homogeneous Charge Compression Ignition (HCCI) engines can have efficiencies as high as compression-ignition, direct-injection (CIDI) engines (an advanced version of the commonly known diesel engine), while producing ultra-low emissions of oxides of nitrogen (NOx) and particulate matter (PM). HCCI engines can operate on gasoline, diesel fuel, and most alternative fuels. While HCCI has been demonstrated and known for quite some time, only the recent advent of electronic sensors and controls has made HCCI engines a potential practical reality. This paper provides a comprehensive overview of the current state-of-the-art in HCCI technology, estimates the potential benefits HCCI engines could bring to U.S. transportation vehicles, and lists the R&D barriers that need to be overcome before HCCI engines might be considered for commercial application.

Two fundamental aspects of HCCI engine combustion have been investigated using a single-zone model with time-varying compression and the full chemical-kinetic mechanisms for iso-octane, a representative liquid-phase fuel. This approach allows effects of the kinetics and thermodynamics to be isolated and evaluated in a well-characterized manner, providing an understanding of the selected fundamental processes. The computations were made using the CHEMKIN-III kinetic-rate code for an 1800 rpm operating condition. The study consists of two parts. First, low-load HCCI operation was investigated to determine the role of bulk-gas reactions as a source for HC and CO emissions. The computations show that as fueling is reduced to equivalence ratios of 0.15 and lower (very light load and idle), the bulk-gas reactions do not go to completion, leading to inefficient combustion and high emissions of HC and CO.

To better understand the factors affecting soot formation in diesel engines, in-cylinder soot and diffusion flame lift-off were measured in a heavy-duty, direct-injection diesel engine. Measurements were obtained at two operating conditions using two commercial diesel fuels and a range of oxygenated paraffinic fuel blends. A line-of-sight laser extinction diagnostic was improved and employed to measure the relative soot concentration within the jet (“jet-soot”) and the rates of soot-wall deposition on the piston bowl-rim. An OH chemiluminescence imaging technique was developed to determine the location of the diffusion flame and to measure the lift-off lengths of the diffusion flame to estimate the amount of oxygen entrainment in the diesel jets. Both the jet-soot and the rate of soot-wall deposition were found to decrease with increasing fuel oxygen-to-carbon ratio (O/C) over a wide range of O/C.

The combustion process in diesel engines deposits soot on the in-cylinder surfaces. Previous works have suggested that these soot deposits eventually break off during cylinder blow-down and the exhaust stroke and contribute significantly to exhaust soot emissions. In order to better understand this potential pathway to soot emissions, the authors recently investigated combusting fuel-jet/wall interactions in a diesel engine. This work, published as a companion paper, showed how soot escaped from the combusting fuel jet and was brought in close proximity to the wall so that it could become a deposit. The current study extends this earlier work with laser-extinction measurements of the soot-deposition rate in the same single-cylinder, heavy-duty DI diesel engine. Measurements were made by passing the beam of a CW-diode laser through a window in the piston bowl rim that was in-line with one of the fuel jets.

Chemiluminescence imaging has been applied to a parametric investigation of diesel autoignition. Time-resolved images of the natural light emission were made in an optically accessible DI diesel engine of the heavy-duty size class using an intensified CCD video camera. Measurements were obtained at a base operating condition, corresponding to a motored TDC temperature and density of 992 K and 16.6 kg/m3, and for TDC temperatures and densities above and below these values. Data were taken with a 42.5 cetane number blend of the diesel reference fuels for all conditions, and measurements were also made with no. 2 diesel fuel (D2) at the base condition. For each condition, temporal sequences of images were acquired from the time of first detectable chemiluminescence up through fully sooting combustion, and the images were analyzed to obtain quantitative measurements of the average emission intensity.

The objective of this investigation is to verify and characterize the influence of fuel volatility on maximum liquid-phase fuel penetration for a variety of actual Diesel fuels under realistic Diesel engine operating conditions. To do so, liquid-phase fuel penetration was measured for a total of eight Diesel fuels using laser elastic-scatter imaging. The experiments were carried out in an optically accessible Diesel engine of the “heavy-duty” size class at a representative medium speed (1200 rpm) operating condition. In addition to liquid-phase fuel penetration, ignition delay was assessed for each fuel based on pressure-derived apparent heat release rate and needle lift data. For all fuels examined, it was observed that initially the liquid fuel penetrates almost linearly with increasing crank angle until reaching a maximum characteristic length. Beyond this characteristic length, the fuel is entirely vapor phase and not just smaller fuel droplets.

A phenomenological description, or “conceptual model,” of how direct-injection (DI) diesel combustion occurs has been derived from laser-sheet imaging and other recent optical data. To provide background, the most relevant of the recent imaging data of the author and co-workers are presented and discussed, as are the relationships between the various imaging measurements. Where appropriate, other supporting data from the literature is also discussed. Then, this combined information is summarized in a series of idealized schematics that depict the combustion process for a typical, modern-diesel-engine condition. The schematics incorporate virtually all of the information provided by our recent imaging data including: liquid- and vapor-fuel zones, fuel/air mixing, autoignition, reaction zones, and soot distributions.

A parametric study of the liquid-phase fuel penetration of evaporating Diesel fuel jets has been conducted in a direct-injection Diesel engine using laser elastic-scatter imaging. The experiments were conducted in an optically accessible Diesel engine of the “heavy-duty” size class at a representative medium speed (1200 rpm) operating condition. The density and temperature at TDC were varied systematically by adjusting the intake temperature and pressure. At all operating conditions the measurements show that initially the liquid fuel penetrates almost linearly with increasing crank angle until reaching a maximum length. Then, the liquid-fuel penetration length remains fairly constant although fuel injection continues. At a TDC density of 16.6 kg/m3 and a temperature of about 1000 K the maximum penetration length is approximately 23 mm. However, it varies significantly as TDC conditions are changed, with the liquid-length being less at higher temperatures and at higher densities.

A combination of optical imaging diagnostics has been applied to the fuel jet of a direct-injection diesel engine to study the ignition and early soot formation processes. Measurements were made in an optically accessible direct-injection diesel engine of the “heavy-duty” size class at a representative medium speed (1200 rpm) operating condition. Two fuels were used, a 42.5 cetane number mixture of the diesel reference fuels and a new low-sooting fuel (needed to reduce optical attenuation at later crank angles) that closely matches both the cetane number and boiling point of the reference fuel mixture. The combustion and soot formation processes are found to be almost identical for both fuels. Ignition and early combustion were studied by imaging the natural chemiluminescence using a calibrated intensified video camera. The early soot development was investigated via luminosity imaging and simultaneous planar imaging of laser-induced incandescence (LII) and elastic scattering.

Laser-induced incandescence (LII) has been explored as a diagnostic for qualitative two-dimensional imaging of the in-cylinder soot distribution in a diesel engine. Advantages of LII over elastic-scatter soot imaging techniques include no interfering signals from liquid fuel droplets, easy rejection of laser light scattered by in-cylinder surfaces, and the signal intensity being proportional to the soot volume fraction. LII images were obtained in a 2.3-liter, single cylinder, direct-injection diesel engine, modified for optical access. To minimize laser sheet and signal attenuation (which can affect almost any planar imaging technique applied to diesel engine combustion), a low-sooting fuel was used whose vaporization and combustion characteristics are typical of standard diesel fuels. Temporal and spatial sequences of LII images were made which show the extent of the soot distribution within the optically accessible portion the combusting spray plume.