Search Results

Intelligent vehicle-to-everything connectivity is an important development trend in the automotive industry. Among various active safety systems, Autonomous Emergency Braking (AEB) has garnered widespread attention due to its outstanding performance in reducing traffic accidents. AEB effectively avoids or mitigates vehicle collisions through automatic braking, making it a crucial technology in autonomous driving. However, the majority of current AEB safety models exhibit limitations in braking modes and fail to fully consider the overall vehicle stability during braking. To address these issues, this paper proposes an improved AEB control system based on a risk factor (AERF). The upper-level controller introduces the risk factor (RF) and proposes a multi-stage warning/braking control strategy based on preceding vehicle dynamic characteristics, while also calculating the desired acceleration.

The present study introduces a novel approach for achieving path tracking of an unmanned bicycle in its local body-fixed coordinate frame. A bicycle is generally recognized as a multibody system consisting of four distinct rigid bodies, namely the front wheel, the front fork, the body frame, and the rear wheel. In contrast to most previous studies, the relationship between a tire and the road is now considered in terms of tire forces rather than nonholonomic constraints. The body frame has six degrees of freedom, while the rear wheel and front fork each have one degree of freedom relative to the body frame. The front wheel exhibits a single degree of freedom relative to the front fork. A bicycle has a total of nine degrees of freedom.

In order to study the tire friction characteristics under wet skid surface, the “pseudo” hydrodynamic pressure bearing effect is used to be equivalent to the hydrodynamics of water film, and an advanced Lugre tire hydroplaning dynamic model is developed by combining the arbitrary pressure distribution function. The water hydroplaning dynamic tests were carried out for 285/70R19.5 tire under wet of different water film thickness and dry conditions, and the parameters of the advanced Lugre tire dynamic model were identified. The results show that the tire water-skiing model proposed in this paper can effectively simulate the friction characteristics of tires under different water film thicknesses. Under dry conditions, 0.5mm water film and 1mm water film road conditions, the relative errors of the maximum tire friction coefficient between the tested and advanced Lugre tire model are 1.11%, 0.12% and 0.16%, respectively.

This paper presents a torque distribution strategy for four-wheel independent drive electric vehicles (4WIDEVs) to achieve both handling stability and energy efficiency. The strategy is based on the dynamic adjustment of two optimization objectives. Firstly, a 2DOF vehicle model is employed to define the stability control objective for Direct Yaw moment Control (DYC). The upper-layer controller, designed using Linear Quadratic Regulator (LQR), is responsible for tracking the target yaw rate and target sideslip angle. Secondly, the lower-layer torque distribution strategy is established by optimizing the tire load rate and motor energy consumption for dynamic adjustment. To regulate the weights of the optimization targets, stability and energy efficiency allocation coefficient is introduced. Simulation results of double lane change and split μ road conditions are used to demonstrate the effectiveness of the proposed DYC controller.

With the development of hardware and control theory, the application of quadcopters is constantly expanding. Quadcopters have emerged in many fields, including transportation, exploration, and object grabbing and placement. These application scenarios require accurate, stable, and rapid control, and a suitable dynamic model is one of the prerequisites. At present, many works are related to it, most of which are modeled using the Newton-Euler method. Some works have also adopted other methods, including the Lagrangian and Hamiltonian methods. This article proposes a new method that solves the Hamiltonian equation of a quadcopter expressed in quasi-coordinate. The external forces and motion of the body are expressed in the quasi-coordinate system of the body, and solved through the Hamiltonian equation. This method simplifies operations and improves computational efficiency. Additionally, a single pendulum is attached to the quadcopter to simulate application scenarios.

The tire frictional characteristics, which are the most critical factors of braking performance, depend on the road condition. Unsafe accidents always occur when driving in a hostile environment, especially under snowy road conditions. The coupled dynamic behaviors between the tire and the snow on the road are closely related to the water film generated from the tire rolling on the snow. The winter tire and summer tire with specification 175/65R14 are modeled separately by the finite element method (FEM), and the stiffness characteristics of the winter tire are analyzed. Further, the coupled dynamic model between the tire and the snowy road is built by considering the tire motion effects of the water film. The tires’ friction coefficient is investigated under the straight snowy road with different velocities.

The towbarless aircraft taxiing system (TLATS) consists of the towbarless towing vehicle (TLTV) and the aircraft. The tractor realizes the towing work by fixing the nose wheel. During the towing process, the tractor driver may cause the aircraft to collide with an obstacle because of the blind spot of vision leading to the accident. The special characteristics of aircraft do not allow us to modify the structure of the aircraft to achieve collision avoidance. In this paper, three degrees of freedom (DOE) kinematic model of the tractor system is established for each of the two cases of pushing and pulling the aircraft, and the relationship between the coordinates of each danger point and the relatively articulated angle of the TLATS and the velocity of the midpoint of the rear axle is derived.

Unsuitable shift control strategies may increase the vehicle jerk and clutch wear. In order to improve the shift quality of electric vehicles (EVs) equipped with dual clutch transmission, this paper proposes an optimal shift control strategy based on linear quadratic regulator, in which weighting matrices are selected by using genetic algorithm (GA). The dynamics of the shift process of the dual clutch transmission is analyzed to establish the dynamic model of the driving system. In addition to the vehicle jerk, the friction work of clutch is also considered as one of the performance criteria and a new linear quadratic objective function is formulated. The optimal weighting matrices for obtaining a globally optimal solution are selected benefit from the global search capacity of genetic algorithm. The optimal target trajectories of the torque of the two clutches and motor are obtained by simulating the linear quadratic regulator (LQR).

Due to the elimination of the mechanical connection between the steering column and steering gear in the Steer-by-Wire (SBW) system, the road-feeling simulation is mainly supplied by the road-feeling motor which loads a drag torque on the steering wheel rather than the actual torque transmitted from the road. To obtain more realistic steering wheel torque, a novel feedback torque of the road-feeling motor fusion estimation method based on the Kalman filter is presented in this paper. Firstly, the model-based estimation method is utilized to estimate the aligning torque between tires and ground which is converted into the rack force through the steering system. Then the estimated rack force is used as the observed data for the Kalman Filter of the sensor-based method and the Kalman Filter-based fusion estimation method is resulted, through which the more realistic feedback torque of the road-feeling motor can be obtained.

Connected and automated vehicles (CAVs) can improve traffic efficiency and reduce fuel consumption. This paper proposes a cooperative game approach to merging sequence and optimal trajectory planning of CAVs at unsignalized intersections. The trajectory of the vehicles in the control zone is optimized by the Pontryagin minimum principle. The vehicle's travel time, fuel consumption, and passenger comfort are considered to construct the joint cost function, completing the optimal trajectory planning to minimize the joint cost function. Analyzing the different states between neighboring CAVs at the intersection to calculate the minimum safety interval. The cooperative game approach to merging sequence aims to minimize the global cost and the merging sequence of CAVs is dynamically adjusted according to the gaming result. The multi-player games are decomposed into two-player games, to realize the goal of the minimal global cost and improve the calculation efficiency.

The road adhesion coefficient has a great impact on the performance of vehicle tires, which in turn affects vehicle safety and stability. A low coefficient of adhesion can significantly reduce the tire's traction limit. Therefore, the measurement of the coefficient is much helpful for automated vehicle control and stability control. Considering that the road adhesion coefficient is an inherent parameter of the road and it cannot be known directly from the information of the on-vehicle sensors. The novelty of this paper is to construct a road adhesion coefficient observer which considers the noise of sensors and measures the unknown state variable by the trained neural network. A Butterworth filter and Adaptive Neural Fuzzy Interference System (ANFIS) are combined to provide the lateral and longitudinal velocity which cannot be measured by regular sensors.

Suspension kinematics and compliance strongly influence the handling performance of the vehicle. The kinematics and compliance characteristics are determined by the suspension geometry and stiffness of suspension bodies and elastic components. However, it is usually inefficient to model all the joints, bushings, and linkage deformation in a full vehicle model. By transforming the complex modeling problem into a data-driven problem tends to be a good solution. In this research, the neural-network-based suspension kinematics and compliance model is built and implemented into a 17 DOF full vehicle model, which is a hybrid model with state variables expressed in the global coordinate system and vehicle coordinate system. The original kinematics and compliance characteristics are derived from multibody dynamics simulation of the suspension system level.

The towbarless aircraft taxiing system (TLATS) consists of the towbarless towing vehicle (TLTV) and the aircraft, of which the nose wheel is lifted and fixed by the picking up and holding system of the TLTV. The aircraft is towed to the destination in a long distance with a high speed of about 40 km/h only driven by the TLTV, which has the advantages of efficiency and economy by comparing with the traditional towing operation at a low speed of 5 km/h and with a short towing distance of about 50 m. However, the increase of the towing velocity leads to an deteriorate vibration problem in terms of the uncomfortable of the driver and reduction of the structure safe life limit, due to the lack of the chassis suspension for the vibration isolation of the TLTV. Therefore, the air suspension is introduced to the TLTV to alleviate the vibration. The dynamic model of the TLATS with air suspensions is derived.

When the drill arm reaches the specified position, the rubber top disk of the propelling beam is pressed against the rock surface by the hydraulic cylinder force and the rock drill starts drilling. Because of the reaction force and the deformation of the drill arm, the propelling beam will be offset from its target position and vibrate, which will affect the drilling accuracy. To analyze the vibration of the propelling beam, the rigid-flexible coupled model is established. The minimum displacement offset of the propelling beam from the initial position is used as the optimization function and the parameters of the rubber top disk are used as optimization variables. The amplitude of the propelling beam at a steady state is used as the constraint. From the simulation results, the rigid-flexible coupled model can describe the vibration of the propelling beam better than the rigid model, especially during the rock drill working stage.

For automated driving vehicles, path planning and trajectory tracking are the core of achieving obstacle avoidance. Real-time external environment perception and vehicle state monitoring play the important role in the decision-making of vehicle operation. Sensor measuring is an important way to obtain vehicle state parameters, but some parameters cannot be measured due to sensor cost or technical reasons, such as vehicle lateral velocity and side-slip angle. This disadvantage will adversely affect the monitoring of vehicle self-condition and the control of vehicle running, even it will lead to erroneous decision-making of vehicles. Therefore, this paper proposes an automated driving path planning and trajectory tracking control method based on Kalman filter vehicle state observer. Some of vehicle state data can be measured accurately by sensors.

In autonomous driving, variations in tire vertical load, tire slip angle, road conditions, tire pressure and tire friction all contribute to uncertainty in tire cornering stiffness. Even the same tire may vary slightly during the manufacturing process. Therefore, the uncertainty of tire cornering stiffness has an important influence for autonomous driving path planning and control strategies. In this paper, the Chebyshev interval method is used to represent the uncertainty of tire cornering stiffness and is combined with a model predictive control algorithm to obtain the trajectory interval bands under local path planning and tracking control. The accuracy of the tire cornering stiffness model and the path tracking efficiency are verified by comparing with the path planning and control results without considering the corner stiffness uncertainties.

The rubber bushing is the key component to suppress vibration in the suspension system, an accurate constitutive model of rubber bushing should capture the amplitude and frequency dependency. Based on the lumped parameter model, three types of rubber bushing models are applied and compared, including the common Kelvin-Voigt model. To evaluate the model parameter and suitable frequency range, the quasi-static and dynamic tests have been performed. Comparing with the testing result, the fractional Kelvin-Voigt model combined with Berg’s friction has the minimum relative error of dynamic stiffness on the whole. Finally, two examples of chassis bushing under different loading conditions are presented. The rubber force and deflection are analyzed in both the time domain and the frequency domain, and the results show the difference of stiffness and hysteresis loop relative to frequency.

In the petroleum and gas industry, cargo truck is one of the most important ways to transfer the skid-mounting from the manufacturer to the job location. Under the condition of bumpy road surface, the random vibration from the ground can easily cause the resonance of the internal equipment components of the skid-mounting, produce large deformation in the pipeline and equipment connection, and even the equipment will be damaged. In this paper, the finite element analysis model and dynamic rigid flexible coupling model of a TEG (Triethyleneglycol) dehydration unit regeneration skid-mounting are established by using the finite element analysis and multi-body dynamics software. The modal analysis of the skid and the vibration of the whole vehicle under different road excitation and driving conditions are carried out. Two solutions are proposed to improve the anti-vibration ability of the skid, and comparative analysis is made.

The tire is one of the key components that affect vehicle performance and ride quality. The rigid ring model has been widely used in the dynamic simulation of tire rolling uneven road surface, and calculate the tire stiffness and force of rim under quasi-static conditions. However, the traditional spring-damping between rim and belt is not accurate enough to describe the viscous damping force and hysteretic behavior of rubber. Therefore, it is necessary to propose a new rigid ring model, considering the viscoelasticity of tire side rubber and hysteretic behavior of rubber, to better adapt to the intermediate frequency response of tire. In this paper, the rigid ring model introduces the fractional derivative damping and friction force element to enhance the dynamic response of tire in higher frequency. Linear damping is replaced by a three-parameter fractional-order derivative damping model, and a Berg friction element was added between rim and belt.

In this paper, a multi-mode active seat suspension with a single actuator is proposed and built. A one-DOF seat suspension system is modelled based on a quarter car model of commercial vehicle with an actuator which is comprised of a DC motor and a gear reducer. Aiming at improving ride comfort and reducing energy consumption, a multi-mode controller is established. According to the seat vertical acceleration and suspension dynamic travel signals, control strategies switch between three modes: active drive mode, energy harvesting mode and plug breaking mode.