Search Results

A vehicle fleet of seven low-mileage gasoline direct injection (GDI) vehicles from the U.S. market were tested to determine if GDI injector deposits were present causing a loss in fuel economy (FE). The real-world vehicles were tested “as-is” from the field. The data shows that, even in a deposit control additive (DCA) mandated market that uses E10 gasoline, injector deposits can still result in up to 2.7 % loss in FE. In addition, the data shows that the level of real-world FE loss is comparable to that demonstrated in the GDI injector fouling test developed to simulate real-world dirty-up of GDI vehicle injectors.

A critical market driver for rear axle lubricants continues to be the improved fuel efficiency, which is related to improvements in power transfer efficiency. Power transfer efficiency improvements are achieved with a reduction in the kinematic viscosity (KV) of rear axle lubricants. General Motors (GM) recently reduced the recommended viscosity grade for their rear axle lubricants from the Society of Automotive Engineers standard (SAE) 75W-90 to SAE 75W-85. This reduction in viscosity continues to require the optimization of rear axle lubricants to ensure durability. Lubricants that form thick elastohydrodynamic (EHD) films and are shear stable even when lower kinematic viscosities are required. This work depicts how a rear axle lubricant was developed and improved with the proper selection of base oil and polymer. This newly developed SAE 75W-85 rear axle fluid was incorporated as factory fill in 2019 in T1 LDPU-GMC Sierra and Chevrolet Silverado 1500 series pickup trucks.

There is still a need in the industry for engine oils that have low viscosities to improve vehicle fuel efficiency but also protect engines from wear. Viscosity modifiers (VMs) are chief additives responsible for adjusting the viscometric characteristics of automotive lubricants. Most notably, VMs have a significant impact on a lubricant's viscosity-temperature relationship as indicated by viscosity index (VI), cold cranking simulator (CCS) viscosity, and high temperature high shear (HTHS) viscosity of engine oils. Functional copolymers bearing branched, linear, or anti-wear functionalities have been synthesized and evaluated for viscometric and wear protection performance. The resulting polymers improved tribofilm formation, shear stability and CCS viscosities. Indirect benefits including Noack improvement and trim oil reduction were observed.

After new transmission lubricants are developed there is an extensive validation program where friction durability testing is performed on multiple clutch materials. Each durability test can run for long terms and the entire validation program can take much longer terms. A well designed lubricant and friction material will deliver the necessary friction control for construction equipment to operate at optimum level. A mechanistic construct has been evaluated to calculate friction durability in clutch systems based on fluid and surface tribological properties. Fluid properties include both boundary frictional and rheological effects. Surface properties include elastic modulus, surface roughness, asperity density and asperity tip radius. Using this mechanistic construct friction durability has been predicted.

There has been a trend in the automotive industry toward the use of lower viscosity engine oils as fuel economy requirements become more demanding across the globe. Lower viscosity fluids may improve fuel economy due to their improved pumpability, lower churning losses, and thinner lubricating films. However, there is one important caveat related to the use of these fluids: the amount of improvement, if any, is hardware design and application dependent. Standard industry fuel economy tests and engines with differing designs may show divergent responses when using lower viscosity engine oils, not always showing an improved fuel economy response. This paper summarizes the work conducted by the authors to demonstrate how and why the inconsistent results in fuel economy can occur with low viscosity oils.

Friction reduction in lubricated components through engine oil formulations has been investigated in the present work. Three different DI packages in combination with one friction modifier were blended in SAE 5 W-20 and SAE 0 W-16 viscosity grades. The friction performance of these oils was compared with GF-5 SAE 5 W-20 oil. A motored cranktrain assembly has been used to evaluate these, in which friction mean effective pressure (FMEP) as a function of engine speeds at different lubricant temperatures is measured. Results show that the choice of DI package plays a significant role in friction reduction. Results obtained from the mini-traction machine (MTM2) provide detailed information on traction coefficient in boundary, mixed and elastohydrodynamic (EHD) lubrication regimes. It has been shown that the results from the cranktrain rig are fairly consistent with those found in MTM2 tests for all the lubricants tested.

Countries from every region in the world have set aggressive fuel economy targets to reduce greenhouse gas emissions. To meet these requirements, automakers are using combinations of technologies throughout the vehicle drivetrain to improve efficiency. One of the most efficient types of gasoline engine technologies is the turbocharged gasoline direct injection (TGDI) engine. The market share of TGDI engines within North America and globally has been steadily increasing since 2008. TGDI engines can operate at higher temperature and under higher loads. As a result, original equipment manufacturers (OEMs) have introduced additional engine tests to regional and OEM engine oil specifications to ensure performance of TGDI engines is maintained. One such engine test, the General Motors turbocharger coking (GMTC) test (originally referred to as the GM Turbo Charger Deposit Test), evaluates the potential of engine oil to protect turbochargers from deposit build-up.

Mobile source emissions standards are becoming more stringent and particulate emissions from gasoline direct injection (GDI) engines represent a particular challenge. Gasoline particulate filter (GPF) is deemed as one possible technical solution for particulate emissions reduction. In this work, a study was conducted on eight formulations of lubricants to determine their effect on GDI engine particulate emissions and GPF performance. Accelerated ash loading tests were conducted on a 2.4L GDI engine with engine oil injection in gasoline fuel by 2%. The matrix of eight formulations was designed with changing levels of sulfated ash (SASH) level, Zinc dialkyldithiophosphates (ZDDP) level and detergent type. Comprehensive evaluations of particulates included mass, number, size distribution, composition, morphology and soot oxidation properties. GPF performance was assessed through filtration efficiency, back pressure and morphology.

There has been a global technology convergence by engine manufacturers as they strive to meet or exceed the ever-increasing fuel economy mandates that are intended to mitigate the trend in global warming associated with CO2 emissions. While turbocharging and direct-injection gasoline technologies are not new, when combined they create the opportunity for substantial increase in power output at lower engine speeds. Higher output at lower engine speeds is inherently more efficient, and this leads engine designers in the direction of overall smaller engines. Lubricants optimized for older engines may not have the expected level of durability with more operating time being spent at higher specific output levels. Additionally, a phenomenon that is called low-speed pre-ignition has become more prevalent with these engines.

Improving vehicle fuel efficiency is a key market driver in the automotive industry. Typically lubricant chemists focus on reducing viscosity and friction to reduce parasitic energy losses in order to improve automotive fuel efficiency. However, in a transmission other factors may be more important. If an engine can operate at high torque levels the conversion of chemical energy in the fuel to mechanical energy is dramatically increased. However high torque levels in transmissions may cause NVH to occur. The proper combination of friction material and fluid can be used to address this issue. Friction in clutches is controlled by asperity friction and hydrodynamic friction. Asperity friction can be controlled with friction modifiers in the ATF. Hydrodynamic friction control is more complex because it involves the flow characteristics of friction materials and complex viscosity properties of the fluid.

Low speed pre-ignition (LSPI) is an undesirable combustion phenomenon that limits the fuel economy, drivability, emissions and durability performance of modern turbocharged engines. Because of the potential to catastrophically damage an engine after only a single pre-ignition event, the ability to reduce LSPI frequency has grown in importance over the last several years. This is evident in the significant increase in industry publications. It became apparent that certain engine oil components impact the frequency of LSPI events when evaluated in engine tests, notably calcium detergent, molybdenum and phosphorus. However, a close examination of the impact of other formulation additives is lacking. A systematic evaluation of the impact of the detergent package, including single-metal and bimetal detergent systems, ashless and ash-containing additives has been undertaken using a GM 2.0L Ecotec engine installed on a conventional engine dynamometer test stand.

Vehicle manufactures are significantly increasing the production of Direct Injection Gasoline (DIG) engines to help meet the requirements of governmental regulations and the demands of consumers. While DIG powertrains offer multiple advantages over conventional gasoline engines they can be susceptible to fuel related deposit formation, specifically within the fuel injector nozzle. Fuel injector deposits have been linked to a number of negative effects that can impact the normal operation of the engine. A DIG deposit test has been developed to evaluate Deposit Control Additives (DCA) and their effect on injector deposits. Multiple metrics for evaluating fuel injector deposits were investigated to determine a suitable method for quantifying deposit formation. Interrogation of the vehicle On-Board Diagnostic (OBD) system was identified as the optimal method for quantifying deposit formation throughout the duration of the test.

To meet increasingly stringent diesel exhaust emissions requirements, original equipment manufacturers (OEMs) have introduced common rail fuel injection systems that develop pressures of up to 2000 bar (30,000 psi). In addition, fuel delivery schemes have become more complicated, often involving multiple injections per cycle. Containing higher pressures and allowing for precise metering of fuel requires very tight tolerances within the injector. These changes have made injectors more sensitive to fuel particulate contamination. Recently, problems caused by internal diesel injector deposits have been widely reported. In this paper, the results of an investigation into the chemical nature and probable sources of these deposits are discussed. Using an array of techniques, internal deposits were analyzed from on a number of sticking injectors from the field and from OEM test stands in North America.

Previous research to understand the mechanism for piston deposit formation in the Sequence IIIG engine test has focused on characterizing the piston deposits. These studies concluded that, in addition to lubricant derived materials, Sequence IIIG piston deposits contain a significant amount of fuel-derived carbonaceous material. The presence of fuel degradation by-products in Sequence IIIG deposits shows that blow-by is a significant contributor to deposit formation. However, blow-by can either assist in the degradation of the lubricant or can simply be a source for organic material which can be incorporated into the deposits. Therefore, a series of modified Sequence IIIG engine tests were conducted to better determine the effect of blow-by on deposit formation. In these studies deposit formation on different parts of the piston assembly were examined since different parts of the piston assembly are exposed to different amounts of blow-by.

Currently there is no axle test aimed specifically at bearing durability in automotive hypoid axles. Existing axle tests are primarily focused on gear distress and lubricant protection of gears. In light of the new test information showing axle bearing distress, there is a need to develop a new bearing durability test for automotive and truck axle lubricants. To fulfill this need, a new bearing durability test has been developed to better assess lubricant requirements for rolling element bearing durability. Although the final test of an axle lubricant is in a driven automobile or truck, an effective screening test based on actual light duty truck conditions can be used to accelerate lubricant development to enhance bearing performance in hypoid axles. This new test simulates actual road durability tests in the lab. A specific load cycle which retains the critical road test loading conditions reduces test time and helps speed up lubricant development.

In the next ILSAC passenger car motor oil specification the Sequence IIIG engine test, as well as two versions of the Thermo-Oxidation Engine Oil Simulation Test (TEOST) have been proposed as tests to determine the ability of crankcase oils to control engine deposits. The Sequence IIIG engine test and the TEOST MHT test are designed to assess the ability of lubricants to control piston deposits and the TEOST 33 test is designed to assess the ability of lubricants to control turbocharger deposits. We have previously characterized the chemical composition of Sequence IIIG piston deposits using thermogravimetric, infrared and SEM/EDS analyses. Sequence IIIG piston deposits contain a significant amount of carbonaceous material and the carbonaceous material is more prevalent on sections of the pistons that should encounter higher temperatures. Furthermore, the carbonaceous material appears to be a deposit formed by the Sequence IIIG fuel.

This report focuses on an extended investigation of the durability of Dual Clutch Transmission (DCT) fluids. The performance requirements of DCT fluids differ from those of traditional step automatic transmission fluids. For that reason, key performance lab tests are discussed in this paper. Friction durability is measured with a modified version of the JASO M348 SAE#2 friction plate test. In addition, results from a vehicle chassis dynamometer test are discussed. This test involves running a 2008 Volkswagen GTI for 60,000 dynamometer miles (42,000 cycles) of severe acceleration and high speed conditions. Finally, a new DCT fluid, which performs well in these tests, offers friction stability and superior wear protection of transmission hardware, when compared to the commercial reference fluid.

This paper reports its findings in three separate parts. First, a comparative study is made among existing commercial dual clutch automatic transmission fluids (DCTFs). Significant differences in fluid torque capacity, friction material compatibility and copper corrosion performance were found among the fluids. Second, both a new vehicle chassis dynamometer durability test and a SAE#2 durability procedure are offered, specifically designed for DCTs. A 2008 VW GTI did well in the severe 60,000 mile chassis dynamometer procedure. Third, a new DCT fluid is discussed.

Biodiesel fuel is a promising new renewable, alternate fuel source. However, its effect on diesel engine oil lubrication is largely untested at present. There is some indication that the use of biodiesel fuel can degrade diesel engine oil performance to such an extent that shortening of oil drain intervals is required. Oil which is fuel-diluted with biodiesel, which is known to contain unsaturated hydrocarbon bonds, would be expected to be more prone to oxidation. Current diesel engines designed to meet environmental standards tend to introduce more soot into the crankcase oil. The new diesel engine oils for use with biodiesel fuel must be capable of dispersing soot to minimize soot-induced viscosity increase of the oil and prevent engine wear. Oils will also need improved oxidation and corrosion inhibition. To examine soot-handling, ASTM D 7156 Mack T-11 engine test results with 20 wt% soy methyl ester in ultra-low sulfur diesel fuel (B20) were employed.

This laboratory presents a new step-automatic transmission fluid with enhanced friction durability and robustness for the Asian marketplace. This mineral-oil-based fluid also meets JASO M315-1A performance requirements on torque capacity, anti-oxidation, anti-wear, extreme pressure (EP), anti-aeration/foam control, copper corrosion and anti-rust performance. The fluid offers a JASO M349 low velocity friction apparatus (LVFA) durability lifetime of over 1100 hours. Moreover, this fluid maintains stable torque capacity during its entire LVFA durability lifetime, across the temperature range of 40 to 120 °C. Similarly, friction level changes with sliding speed are smaller than experienced by other commercial factory-fill ATFs. These critical performance features are due to a new fluid friction system approach, which may enable new types of transmission hardware or calibration.