Search Results

A few reports suggest differences in injury outcomes between cadaver tests and real-world accidents under almost similar conditions. This study hypothesized that muscle activity could primarily cause the differences, and then developed a human body finite element (FE) model with individual muscles. Each muscle was modeled as a hybrid model of bar elements with active properties and solid elements with passive properties. The model without muscle activation was firstly validated against five series of cadaver test data on impact responses in the anterior-posterior direction. The model with muscle activation levels estimated based on electromyography (EMG) data was secondly validated against four series of volunteer test data on bracing effects for stiffness and thickness of an upper arm muscle, and braced driver's responses under a static environment and a brake deceleration.

To investigate the effect of muscle activity in pre-impact on injury outcome, we developed a human arm finite element model with muscles which consisted of solid elements and truss elements that could be used for simulating muscle stiffness change for the inputted activity and 3-D geometry of each muscle. Two series of experimental tests on muscle stiffness change and arm flexion were conducted for validation of the model. Comparisons between the simulation results and test data indicated the model validity. Lateral impact simulations for a left arm demonstrated that the muscle activity in pre-impact had significant effects on the motion and stress distribution of the arm bones.

Breath alcohol interlock systems are used in Europe and the U.S. for drunk driving offenders, and a certain effect has been revealed in the prevention of drunk driving. Nevertheless, problems remain to be solved with commercialized detectors, i.e., a person taking the breath alcohol test must strongly expire to the alcohol detector through a mouthpiece for every test, more over the determination of the breath alcohol concentration requires more than 5 seconds. The goal of this research is to develop a device that functions suitable and unobtrusive enough as the interlock system. For this purpose, a new alcohol detector, which does not require a long and hard blowing to the detector through a mouthpiece, has been investigated. In this paper, as a tool available on board, a contact free alcohol detector for the prevention of drunk driving has been developed.

A task group within the SAE Automotive Corrosion and Protection (ACAP) Committee continues to pursue the goal of establishing a standard test method for in-laboratory cosmetic corrosion evaluations of finished aluminum auto body panels. The program is a cooperative effort with OEM, supplier, and consultant participation and is supported in part by USAMP (AMD 309) and the U.S. Department of Energy. Numerous laboratory corrosion test environments have been used to evaluate the performance of painted aluminum closure panels, but correlations between laboratory test results and in-service performance have not been established. The primary objective of this project is to identify an accelerated laboratory test method that correlates with in-service performance. In this paper the type, extent, and chemical nature of cosmetic corrosion observed in the on-vehicle exposures are compared with those from some of the commonly used laboratory tests

In developing the features of a spark-ignition combustion chamber, optical combustion diagnostic technology was employed to understand the factors contributing to knock propensity of the combustion system. This optical combustion visualization equipment utilizes optical prisms located around the periphery of the spark plug shell to measure light intensity of combustion. By synchronizing light intensity and cylinder pressure measurements to crankshaft position, local tracking of combustion progression is accomplished. This method was used to track knock occurrences and to evaluate their controlling parameters within this combustion system. Cylinder head and piston top geometries were developed as a result of this combustion visualization. Recommendations derived from these studies were successfully used to achieve objectives of this engine development program which included improvements in torque and power output, fuel economy, and combustion stability.

The ability to predict the interior acoustic sound field in a vehicle is important in order to avoid or to minimize unwanted noise conditions, such as boom or high pressure levels at cavity resonance frequencies. In this work an acoustic modal analysis is carried out for a minivan. The testing procedure is discussed and some results are shown. With the seats removed and for low frequencies the interior of the vehicle is similar to a rectangular box for which an analytical solution exists. At higher frequencies and with the seat, the interior acoustic field displays complex mode shapes.

Injuries of the human brain and spinal cord associated with the central nervous system (CNS) are seen in automotive accidents. CNS injuries are generally categorized into severe injuries (AIS 3+). However, it is not clear how the restraint conditions affect the CNS injuries. This paper presents a newly developed three-dimensional (3D) finite element head-neck model in order to investigate the biomechanical responses of the brain-spinal cord complex. The head model consists of the scalp, skull, and a detailed description of the brain including the cerebrum, cerebellum, brainstem with distinct white and gray matter, cerebral spinal fluid (CSF), sagittal sinus, dura, pia, arachnoid, meninx, falx cerebri, and tentorium. Additionally, the neck model consists of the cervical vertebral bodies, intervertebral discs, muscles, ligaments, spinal cord with white and gray matter, cervical pia, and CSF.

1 In general, the engine brake performance of a vehicle with an automatic transmission (AT) is inferior to that of a vehicle with a manual transmission (MT), without manually downshifting the transmission. Especially, in commercial vehicles having great variations in load capacity, improvements in engine brake performances are significant issues for vehicles with an AT in terms of both safety and performance. For such circumstances, Aisin Seiki has succeeded in the development of a 6-speed AT for commercial vehicles with an engine control system that enables the vehicle to decelerate according to desire of drivers in various driving conditions. An outline of the development of this control system is presented below.

Posterior translation of the tibia with respect to the femur can stretch the posterior cruciate ligament (PCL). Fifteen millimeters of relative displacement between the femur and tibia is known as the Injury Assessment Reference Value (IARV) for the PCL injury. Since the anterior protuberance of the tibial plateau can be the first site of contact when the knee is flexed, the knee bolster is generally designed with an inclined surface so as not to directly load the projection in frontal crashes. It should be noted, however, that the initial flexion angle of the occupant knee can vary among individuals and the knee flexion angle can change due to the occupant motion. The behavior of the tibial protuberance related to the knee flexion angle has not been described yet. The instantaneous angle of the knee joint at the timing of restraining the knee should be known to manage the geometry and functions of knee restraint devices.

The most severe ankle skeletal injury called pilon fractures can cause long term disability and impairment. Based on previous experimental studies, the pilon fractures are regarded as caused by a high-energy compressive force in the ankle joint and affected by a muscular tension force generated by emergency braking. However, quantitative injury criteria for the pilon fractures are still unknown. More accurate prediction of bone fractures in the distal tibia using a FE model of human lower leg can help us know the quantitative injury criteria. Therefore we newly proposed an anisotropic inelastic constitutive model of cortical bone including damage evolution and then implemented it to a FE code, LS-DYNA. The proposed model successfully reproduced most of anisotropy, strain rate dependency, and asymmetry of tension and compression on material and failure properties of human femoral cortical bone.

This paper gives an outline of the steering assistance system (hereinafter, SAS) and a description of its key technology: the lane recognition algorithm. To accommodate a variety of driving styles, the SAS is equipped with a lane keeping assistance mode (LKA mode) and a lane departure warning mode (LDW mode) that can be selectively set by the driver. The former mode works in combination with adaptive cruise control (ACC) and carries the advantage of relieving the driving load that is placed on the driver. The latter mode has the benefit of reducing the danger of lane departure accidents caused by the driver dozing off and taking his eyes off the road. The newly developed lane recognition ECU has a simple hardware set-up of two 32-bit microcomputers. The lane recognition algorithm was constructed on the basis of a logic process that analyzes pattern edge points and selects a set of edge points that most closely resemble lanemarks.

In order to further improve the performance of NOx storage-reduction catalysts (NSR catalysts), focus was placed on their high temperature performance deterioration via sulfur poisoning and heat deterioration. The reactions between the basicity or acidity of supports and the storage element, potassium, were analyzed. It was determined that the high temperature performance of NSR catalysts is enhanced by the interaction between potassium and zirconia, which is a basic metal oxide. Also, a new zirconia-titania complex metal oxides was developed to improve high temperature performance and to promote the desorption of sulfur from the supports after aging.

The anti-shudder effect of ATF additives and their mechanisms have been investigated. Anti-shudder durability was evaluated using an automatic transmission (AT) on an engine stand under continuously slip-controlled condition. The addition of over-based Ca-sulfonate and friction modifier (FM) remarkably improved the anti-shudder durability of ATF. The surface roughness of the contact area (contact area roughness) of the clutch plates was measured by an electron probe surface roughness analyzer. To evaluate the boundary frictional properties of the adsorbed film formed, the friction coefficient of the clutch plates in the absence of oil was examined after the anti-shudder durability test. It was found that shudder occurrence was strongly correlated with the contact area roughness and the boundary frictional property of the steel plate surface. Large contact area roughness and low boundary friction were preferred to prevent shudder.

Avoiding low-frequency pressure pulsations and establishing a good axial static pressure distribution are primary concerns for open jet wind tunnels. The current research was conducted to ensure the full scale Chrysler Aero-Acoustic Wind Tunnel (AAWT) design is consistent with good performance in these two areas. Experiments were conducted in two tunnels: a 1/3.6-scale closed-circuit tunnel and a 1/12-scale open-loop tunnel. Results from both are consistent, and a configuration that exhibits i) minimal pulsations for both empty test section and 15% vehicle blockage and ii) a good axial static pressure distribution has been identified for the AAWT. The results illustrate the effect of open jet length, collector geometry, and plenum geometry on pulsation levels and highlight the spatial variation of the pulsation levels within the plenum chamber. Pulsation levels were observed to increase with increasing open jet length and decreasing collector throat area.

Adhesive joining is a common autobody subassembly technique especially for outer panels, where visible spot welding is objectionable. To accommodate mass production with the use of certain adhesives very high thermal gradient usually exists, which may result in panel dimensional distortion and variation. The temperature distribution over location and over time are monitored, and its impact to panel dimension is investigated. Experimental results on the effect of the distance between panel and induction coil on the panel temperature is obtained. The thermal induced shape distortion is simulated with a simplified FEA model. The approach to improvement of the induction curing process is discussed.

In this paper, an analytical method is proposed for determining the stress distributions in steering knuckle/tapered stud assemblies. The method is based on solutions of the plane stress thick cylinder interference fit problem with modifications to account for the effects of stud taper and dissimilar component materials. The analytical solutions are applied to knuckle/tapered stud assemblies. The results from the analytical solutions are compared to those from a finite element analysis. It is shown that the analytical and FEA results are in good agreement for several load and frictional conditions, and the hoop and radial stress solutions presented in this paper are good engineering solutions to the knuckle/tapered stud problem where the draw distance is provided.

For the new 4.7 L, V-8 engine, which was introduced in the all new 1999 Jeep Grand Cherokee, Chrysler product engineers found they needed a bedplate material that was significantly stronger and stiffer than gray iron to help meet engine weight requirements. The material also had to provide good NVH characteristics, be cost effective, and machinable. Intermet Corporation, the casting supplier, wanted a material that was significantly tougher than gray iron, would cast sound in complex sections, and which could be reliably produced on a cost effective basis. This paper presents an overview of the development, properties, casting practices, and engine validation of enhanced compacted graphite iron, a material specifically developed and tailored for the bedplate of the new 4.7 liter engine.

This paper is a discussion on a statistical problem solving approach to determine the root cause of shimmy in a Chrysler Jeep® Cherokee. A blend of statistical approach with strong analytical quantification is used to give the problem solving a non-subjective flavor. The statistical aspect of the problem solving consists of DOE (Design of Experiments) while the analytical portion describes the instrumentation, data acquisition and analysis.

Chrysler began a limited development program directed toward a new automatic transmission fluid (ATF) early in 1989 and launched a full time effort in 1994. The development process for the new ATF involved a significant level of bench testing and eventually vehicle tests to evaluate the durability and shift quality of the ATF. The bench tests included those that pertain to oxidation and shear stability, anti-wear, frictional properties and torque converter shudder. Vehicle tests were primarily extended durability in both internal vehicle fleets and at external taxi sites. The mileage accumulated in this phase of the development program exceeded two million miles, all with no fluid drains out to 100,000 miles. Additionally, shift feel tests were conducted in Chrysler vehicles to verify compliance to targets. This paper summarizes the tests and results that lead to the development of the new Chrysler fill-for-life automatic transmission fluid.

As part of the International Lubricant Standardization and Approval Committee's (ILSAC) goal of developing a global automatic transmission fluid (ATF) specification, members have been evaluating test methods that are currently used by various automotive manufacturers for qualifying ATF for use in their respective transmissions. This report deals with comparing test methods used for determining torque capacity in friction systems (shifting clutches). Three test methods were compared, the Plate Friction Test from the General Motors DEXRON®-III Specification, the Friction Durability Test from the Ford MERCON® Specification, and the Japanese Automotive Manufacturers Association Friction Test - JASO Method 348-95. Eight different fluids were evaluated. Friction parameters used in the comparison were breakaway friction, dynamic friction torque at midpoint and the end of engagement, and the ratio of end torque to midpoint torque.