Search Results

This study focuses on evaluation of various fuels within a conventional gasoline internal combustion engine (ICE) vehicle and the implementation of advanced emissions reduction technology. It shows the robustness of the implemented technology packages for achieving ultra-low tailpipe emissions to different market fuels and demonstrates the potential of future GHG neutral powertrains enabled by drop-in lower carbon fuels (LCF). An ultra-low emission (ULE) sedan vehicle was set up using state-of-the-art engine technology, with advanced vehicle control and exhaust gas aftertreatment system including a prototype rapid catalyst heating (RCH) unit. Currently regulated criteria pollutant emission species were measured at both engine-out and tailpipe locations. Vehicle was run on three different drive cycles at the chassis dynamometer: two standard cycles (WLTC and TfL) at 20°C, and a real driving emission (RDE) cycle at -7°C.

Software-in-the-Loop (SiL) test environments are the ideal virtual platforms for enabling continuous-development, -integration, -testing -delivery or -deployment commonly referred as Continuous-X (CX) of the complex functionalities in the current automotive industry. This trend especially is contributed by several factors such as the industry wide standardization of the model exchange formats, interfaces as well as architecture definitions. The approach of frontloading software testing with SiL test environments is predominantly advocated as well as already adopted by various Automotive OEMs, thereby the demand for innovating applicable methods is increasing. However, prominent usage of the existing monolithic architecture for interaction of various elements in the SiL environment, without regarding the separation between functional and non-functional test scope, is reducing the usability and thus limiting significantly the cost saving potential of CX with SiL.

The prime factor which influences noise and vibrations of electro-mechanical drives is wear at the components. This paper discusses the numerical methods developed for abrasion, vibration calculations and the coupling between wear and Noise Vibration and Harshness (NVH) models of the drive unit. The vibration domain model, initially, focuses on the calculations of mechanical excitations at the gear shafts which are generated via a nonlinear dynamic model. Furthermore, the bearings are studied for the influences on their stiffness and eventually their impact on the harmonics of the drivetrain. Later, free and forced vibrations of the complete drivetrain are simulated via a steady-state dynamic model. Consequently, the paper concentrates on the abrasion calculations at the gears. Wear is a complex process and understanding it is essential for determining the vibro-acoustics characteristics.

In order to optimize spray layouts of commonly used high-pressure injectors for gasoline direct injection (GDI) engines featuring multi-hole valve seats, a detailed understanding of the cause-effect relation between inner spray hole geometries and inner flow conditions, initializing the process of internal mixture formation, is needed. Therefore, a novel measurement setup, capable of determining spray hole individual mass flow rates, is introduced and discussed. To prove its feasibility, a 2-hole configuration is chosen. The injected fuel quantities are separated mechanically and guided to separate pressure tight measurement chambers. Each measurement chamber allows for time resolved mass flow rate measurements based on the HDA measurement principle (German: “Hydraulisches Druck-Anstiegsverfahren”).

Large Eddy Simulations (LES) and tracer-based Laser-Induced Fluorescence (LIF) measurements were performed to study the dynamics of fuel wall-films on the piston top of an optically accessible, four-valve pent-roof GDI research engine for a total of eight operating conditions. Starting from a reference point, the systematic variations include changes in engine speed (600; 1,200 and 2,000 RPM) and load (1000 and 500 mbar intake pressure); concerning the fuel path the Start Of Injection (SOI=360°, 390° and 420° CA after gas exchange TDC) as well as the injection pressure (10, 20 and 35 MPa) were varied. For each condition, 40 experimental images were acquired phase-locked at 10° CA intervals after SOI, showing the wall-film dynamics in terms of spatial extent, thickness and temperature.

Particulate emissions from Gasoline Direct Injection (GDI) engines have been an important topic of recent research interest due to their known environmental effects. This review paper will characterise the influence of different gasoline direct injection fuel systems on particle number (PN) emissions. The findings will be reviewed for engine and vehicle measurements with appropriate driving cycles (especially real driving cycles) to evaluate effects of the fuel injection systems on PN emissions. Recent technological developments alongside the trends of the influence of system pressure and nozzle design on injector tip wetting and deposits will be considered. Besides the engine and fuel system it is known that fuel composition will have an important effect on GDI engine PN emissions. The evaporation qualities of fuels have a substantial influence on mixture preparation, as does the composition of the fuel itself.

The fuel spray behavior in the near nozzle region of a gasoline injector is challenging to predict due to existing pressure gradients and turbulences of the internal flow and in-nozzle cavitation. Therefore, statistical parameters for spray characterization through experiments must be considered. The characterization of spray velocity fields in the near-nozzle region is of particular importance as the velocity information is crucial in understanding the hydrodynamic processes which take place further downstream during fuel atomization and mixture formation. This knowledge is needed in order to optimize injector nozzles for future requirements. In this study, the results of three experimental approaches for determination of spray velocity in the near-nozzle region are presented. Two different injector nozzle types were measured through high-speed shadowgraph imaging, Laser Doppler Anemometry (LDA) and X-ray imaging.

The official Indian accident statistics show that the number of road accidents and fatalities are one of the highest worldwide. These official statistics provide important facts about the current accident situation. It is suspected that for various reasons not all accidents are reported to the official statistic. This study estimates the degree of underreporting of traffic accidents with casualties in India. In order to get a national overview of the traffic accident situation it is necessary to improve the knowledge about underreported accidents. Therefore, the in-depth accident database of “Road Accident Sampling System India” (RASSI) was analyzed [1]. This project is organized by a consortium that has collected traffic accidents scientifically in four different regions since 2011 on the spot which have been reported either by police or by local hospitals and own patrol by RASSI engineers.

The fuel-independent particulate emissions of a direct injection gasoline engine were investigated. This was done by running the engine with reference gasoline at four different loads and then switching to hydrogen or methane port fuel operation and comparing the resulting particulate emissions and their size distribution. Differences in the combustion characteristics of hydrogen and gasoline were accounted for by diluting the inlet air with nitrogen and matching the pressure or heat release traces to those of gasoline operation. Methane operation is expected to generate particulate emissions lower by several orders of magnitude compared to gasoline and hydrogen does not contribute to carbon soot formation because of the lack of carbon atoms in the molecule. Thus, any remaining particulate emissions at hydrogen gas operation must arise from non fuel related sources, e.g. from lubrication oil, metal abrasion or inlet air.

This paper presents the development of a novel direct coil cooling approach which can enable high performance for electric traction motor, and in further significantly reduce motor losses. The proposed approach focuses on bypassing critical thermal resistances in motor by cooling coils directly in stator slots with oil flow. Firstly, the basic configuration and features are shown: sealed stator slots to air gap, pressure reservoirs on both side of the slots and slot channels for oil flow. The key to enhance thermal performance of the motor here is based on introducing fluid guiding structure in the slot channels. Next, heat transfer in the channel with guiding structure is investigated by CFD and compared with bare slot channel without guiding structure. For studying the effectiveness of proposed cooling concept, numerical analysis is conducted to compare it with HEV favored oil impingement cooling.

Cost reduction of engine management systems (EMS) for two-wheeler applications is the key to utilize their potentials compared to carburetor bikes regarding emissions, fuel economy and system robustness. In order to reduce the costs of a system with port fuel injection (PFI) Bosch is developing an EMS without a manifold air pressure (MAP) sensor. The pressure sensor is usually used to compensate for different influences on the air mass, which cannot be detected via the throttle position sensor (TPS) and mean engine speed. Such influences are different leakage rates of the throttle body and changing ambient conditions like air pressure. Bosch has shown in the past that a virtual sensor relying on model based evaluation of engine speed can be used for a detection of leakage air mass in idling to improve the pre-control of the air-fuel ratio. This provides a functionality which so far was only possible with an intake pressure sensor.

Regarding the strongly growing two-wheeler market fuel economy, price and emission legislations are in focus of current development work. Fuel economy as well as emissions can be improved by introduction of engine management systems (EMS). In order to provide the benefits of an EMS for low cost motorcycles, efforts are being made at BOSCH to reduce the costs of a port fuel injection (PFI) system. The present paper describes a method of how to reduce the number of sensors of a PFI system by the use of sophisticated software functions based on high-resolution engine speed evaluation. In order to improve the performance of a system working without a MAP-sensor (manifold air pressure sensor) an air charge feature (ACFn) based on engine speed is introduced. It is shown by an experiment that ACFn allows to detect and adapt changes in manifold air pressure. Cross-influences on ACFn are analyzed by simulations and engine test bench measurements.

In order to fulfil emission legislation and achieve good drivability of combustion-engine-powered vehicles, information about the air charge and feedback about the engine condition is necessary. In current systems, different sensors are used, e.g. the MAP (manifold air pressure) sensor and a lambda sensor. Aiming at reducing costs, efforts are being made to reduce the number of sensors while still retrieving the necessary information. Various engine speed based functions are state-of-the-art for automotive engines, e.g. for fuel-calibration, misfire-detection etc. Those functions evaluate the engine speed fluctuations during a working cycle induced by combustion. For multiple-cylinder engines, those influences are overlapping, therefore evaluation possibilities are limited. The work presented is based on the effect that at a single-cylinder engine, there is no overlap of combustion influences of various cylinders on the crankshaft.

The SAE J2716 SENT (Single Edge Nibble Transmission) Protocol has entered production with a number of announced products. The SENT protocol is a point-to-point scheme for transmitting signal values from a sensor to a controller. It is intended to allow for high resolution data transmission with a lower system cost than available serial data solution. The SAE SENT Task Force has developed a number of enhancements and clarifications to the original specification which are summarized in this paper.

The emissions legislation in the US and Europe introduces the need for the application of diesel particulate filters (DPF) in most diesel vehicles. In order to fulfill future OBD legislations, which include more stringent requirements on monitoring the functionality of those particulate filters, new sensors besides the differential pressure sensor are necessary. The new sensors need to directly detect the soot emission after DPF and withstand the harsh exhaust gas environment. Based on multi layer ceramic sensor technology, an exhaust gas sensor for particulate matter (EGS-PM) has been developed. The soot-particle-sensing element consists of two inter-digitated comb-like electrodes with an initially infinite electrical resistance. During the sensor operation, soot particles from the exhaust gas are collected onto the inter-digital electrodes and form conductive paths between the two electrode fingers leading to a drop of the electrical resistance.

This paper looks at the underlying fundamentals of diesel fuel system lubrication for the highly-loaded contacts found in fuel injection equipment like high-pressure pumps. These types of contacts are already occurring in modern systems and their severity is likely to increase in future applications due to the requirement for increased fuel pressure. The aim of the work was to characterise the tribological behavior of these contacts when lubricated with diesel fuel and diesel fuel treated with lubricity additives and model nitrogen and sulphur compounds of different chemical composition. It is essential to understand the role of diesel fuel and of lubricity additives to ensure that future, more severely-loaded systems, will be free of any wear problem in the field.

Increasing injection pressures together with Diesel fuel lubricated Common Rail pumps replacing oil lubricated systems demand a more sophisticated investigation of robustness and durability against particle contamination of fuel. The established way of requiring filtration efficiency levels per lab standard is not significant enough if we look at variable factors like vibration of the fuel filter and viscosity of the fuel. Because these and other factors tremendously influence filtration efficiency, future Diesel FIE cleanliness requirements will need to define an allowable contamination limit downstream of the filter. More precisely, this is not a scalar limit but a contamination collective that considers the varying vehicle filtration and operating environment. This paper describes a procedure for defining allowable contamination limits of the FIE components. The procedure includes sensitivity, robustness and “key life” tests.

1 High precision high pressure diesel common rail fuel injection systems play a key role in emission control, fuel consumption and driving performance. Deposits have been observed on internal injector components, for example in the armature assembly, in the slots of the piston and on the nozzle needle. The brownish to colourless deposits can adversely impact driveability and result in non-compliance with the Euro 4 or Euro 5 emission limits. The deposits have been extensively studied to understand their composition and their formation mechanism. Due to the location of these deposits, the influence of combustion gas can be completely ruled out. In fact, their formation can be explained by interactions of certain diesel fuel additives, including di- and mono-fatty acids. This paper describes the methodology used and the data generated that support the proposed mechanisms. Moreover, approaches to avoid such interactions are discussed.

Today's wide range oxygen sensors are based on the limiting current principle, where an applied voltage induces electrochemical reactions in a ceramic cell. Since the diffusive transport of exhaust gas to the electrodes is limited by a transport barrier, the resulting electric current can be related to the exhaust gas composition. A model is presented which describes the transient transport of gas mixtures from the bulk exhaust gas to the electrodes of an oxygen sensor at variable pressure and composition. The internal structure of the transport barrier was accounted for by geometrical parameters. A variety of numerical results are compared with experimental data.

Since the brake colloquium in 2004 the role of climatic conditions and their relations to noise occurrence, sound pressure level and friction coefficient level is widely discussed in the US and European working groups on brake noise. A systematic study has been started to investigate the influence of relative humidity, absolute humidity and temperature on brake noise and the corresponding friction coefficient level. In this study an enormous effort was taken to keep the influences of the brake parameters, e.g. lining material, Eigenfrequencies and dimensions of the different components as small as possible to investigate the climatic influence only. Strategic humidity and temperature levels were tested according to the Mollier-Entropy-Enthalpy-Diagram which are corresponding to the seasons in the various international regions. A regression analysis evaluates the correlation and the influence of each parameter to noise and friction coefficient level.