Search Results

We have developed a methodology for predicting combustion and emissions in a Homogeneous Charge Compression Ignition (HCCI) Engine. The methodology judiciously uses a fluid mechanics code followed by a chemical kinetics code to achieve great reduction in the computational requirements; to a level that can be handled with current computers. In previous papers, our sequential, multi-zone methodology has been applied to HCCI combustion of short-chain hydrocarbons (natural gas and propane). Applying the same procedure to long-chain hydrocarbons (iso-octane) results in unacceptably long computational time. In this paper, we show how the computational time can be made acceptable by developing a segregated solver. This reduces the run time of a ten-zone problem by an order of magnitude and thus makes it much more practical to make combustion studies of long-chain hydrocarbons.

High-speed diagnostics capable of accurately resolving emission transients are required to provide the most detailed understanding and optimization of active exhaust-emissions-treatment processes, such as NOX adsorbers. A portable, mass-spectrometry-based instrument with high temporal resolution, linear response and broad dynamic range is described. This instrument provides transient-concentration measurement capability for many relevant exhaust species including total NOX. In applications for evaluation of NOX-adsorber systems using heavy-duty diesel engines, the instrument revealed relevant emission transients not previously resolved with conventional analyzers. Specifically, the instrument resolved transient emissions associated with the competition between desorption and reduction rates. The temporal resolution of the instruments is sufficient to resolve kinetic rates of the NOX-adsorber system.

The advantages and disadvantages for the current oil consumption measurement systems, including the real-time oil consumption measurement and traditional weight methods, are reviewed. Based on the review, the Smart Oil Consumption Measuring System developed by Cummins Engine Co. in an effort to resolve some of the disadvantages of the systems developed earlier, especially compared to the Gravity Fed oil consumption measurement system, will be discussed. In addition, the uncertainty analysis of the Smart Oil Consumption Measuring System will also be briefly discussed here. The Smart Oil Consumption Measuring System has proven to be an effective tool to measure the oil consumption at almost any engine test conditions, including the steady and cyclic tests in a shorter time than most of traditional oil consumption measurement systems.

The specific goal of this project was to determine if there is a difference in the lube oil degradation rates in a heavy-duty diesel engine equipped with an EGR system, as compared to the same configuration of the engine, but minus the EGR system. A secondary goal was to develop FTIR analysis of used lube oil as a sensitive technique for rapid evaluation of the degradation properties of lubricants. The test engine selected for this work was a Caterpillar 3176 engine. Two engine configurations were used, a standard 1994 design and a 1994 configuration with EGR designed to meet the 2004 emissions standards. The most significant changes in the lubricant occurred during the first 50-100 hours of operation. The results clearly demonstrated that the use of EGR has a significant impact on the degradation of the engine lubricant.

In order to meet EPA's emission requirements for 1999 diesel engines, soot levels in the crankcase oil will increase significantly due to retarded timing to lower NOx. This study uses the Cummins M11 engine at soot levels up to 9% in the crankcase oil to demonstrate how oils can be formulated to prevent valve train wear, extend filter life, and maintain oil pumpability. The study includes the oil formulation development and the evaluation of API CG-4/SJ oils at 4.5% soot and API CH-4/SJ oils at 9% soot. In addition it includes X-Ray Photoelectron Spectroscopy (XPS) for surface film analysis and Surface Optical Profilometry and Scanning Electron Microscopy (SEM) of the valve train valve-bridges and rocker pads to determine the mechanism of failure. The oil's low temperature rheology as it affects oil pumpability is defined by Mini Rotary Viscometer (MRV TP-1), Scanning Brookfield Test (SBT), and Cold Cranking Simulator (CCS).

This paper examines the feasibility of using the boundary element method (BEM) and the Rayleigh integral to assess the sound radiation from engine components such as oil pans. Two oil pans, one cast aluminum and the other stamped steel, are used in the study. All numerical results are compared to running engine data obtained for each of these oil pans on a Cummins engine. Measured running-engine surface velocity data are used as input to the BEM calculations. The BEM models of the oil pains are baffled in various ways to determine the feasibility of analyzing the sound radiated from the oil pan in isolation of the engine. Two baffling conditions are considered: an infinite baffle in which the edge of the oil pan are attached to an infinite, flat surface; and a closed baffle in which the edge of the oil pan is sealed with a rigid structure. It is shown that either of these methods gives satisfactory results when compared to experiment.

A survey is made of compression brake noise levels in heavy duty diesel trucks, using test procedures based on the ISO and EPA driveby acceleration noise tests. The data shows that compression brake noise levels are very high if worn out or open stack exhaust systems are used. Compression brake noise is also audible with OEM exhaust systems and, in at least one case, potentially objectionable. Two methods for reducing brake noise are investigated: improved mufflers and the use of an exhaust brake with the compression brake. Both techniques demonstrate a potential for reducing compression brake noise.

In this paper, a procedure for the measurement of noise produced by compression brakes on heavy duty trucks is proposed and evaluated. The test procedure is an adaptation of the ISO exterior vehicle noise regulation, ISO 362, to measure compression brake noise. The test consists of two parts, a driveby test and a stationary brake test, which are both developed to accentuate compression brake noise. The proposed test is demonstrated to provide results that are indicative of on-road compression brake noise. The sensitivity of the test results to variations in several test parameters is also examined.

Evolving diesel engine design trends are expected to include fuel systems operating at significantly higher pressures and temperatures than in the past. Accordingly, meaningful laboratory tests are needed to help guide this development. Two candidate test methods were evaluated in this exploratory study. Scuffing Load Ball-on Cylinder Lubricity Evaluator (BOCLE) and Modified High-Frequency Reciprocating Rig (HFRR) test results covering a range of operating temperatures were compared with fuel property data. Correlations of the Modified HFRR test data with BOCLE results were also made.

The ability of a piston oil ring to conform to liner distortions during engine operation is directly related to its radial stiffness. The ability to conform is also very important for controlling lubricant oil consumption and emissions. This paper describes the procedure utilized to investigate the technical feasibility of using flexible high performance engineering plastics to replace metal as base material for oil rings. Bench tests and engines were used to select and evaluate different types of plastics for wear resistance and structural integrity. Engine test results indicated no structural failures but wear levels were found to be unacceptably high for use in durable heavy duty diesel engines.

The EPA Heavy Truck Driveby Noise test is used to regulate trucks over 10,000 pounds GVW. The EPA test procedure is based on SAE J366. The EPA/J366 procedure is used both as a regulatory compliance tool and as a development tool. When the test procedure is used as a development tool, the goal is to determine the most cost effective means of meeting the legal requirement. Since J366 was not intended as a development tool, it can be difficult or misleading to use it to make decisions on product configuration. In order to use J366 successfully in vehicle or engine development, one must understand and properly account for the inherent variability of the J366 driveby test procedure. This paper examines both the extent and some of the sources of J366 driveby test variability. Strategies are proposed to ensure the proper interpretation of test results. Several repeat tests are required to accurately determine a small change in driveby noise level.

Reports of disabling diesel engine seal failures which accompanied the introduction of low sulfur diesel fuel in October '93 prompted an in-depth survey of diesel fuel chemical and physical properties. The purpose of the survey was to anticipate other possible problems which might arise with the newly introduced low sulfur fuels. The survey will produce a database containing over 1000 number 2 diesel fuels from various parts of the US. About 75% of the samples tested were on-highway low sulfur diesel fuels. Samples analyzed were from the D-A Lubricant Company, Cummins customers failures (truck fleets of various sizes), and a number of retail fueling stations. Properties under investigation are % Sulfur, Cloud/Pour Points, Viscosity, API Gravity, TAN/TBN, Boiling Range, Aromatics content, Heat Content, Lubricity, and Peroxide number.

Corrosive wear of non-ferrous engine components by lubricants is a concern of all major heavy duty diesel engine manufacturers since warranty on key engine components has been extended to 500,000 miles. Several commercial lubricants have been linked to premature cam and rod bearing failures induced by corrosion in certain fleets. Although the overall failure rate is low, specific fleets have experienced significantly higher failure rates due to the lubricants used. These failures usually occur at high mileages but less than 500,000 miles. This kind of slow corrosion easily escapes detection of engine tests contained in current oil specifications, and it represents a serious issue in long term warranty cost to diesel engine manufacturers. A comprehensive fleet database has been established to identify the most corrosive lubricants. These lubricants have served as reference oils to develop a corrosion bench test.

A high horsepower, low heat rejection diesel engine is being developed to meet future Army heavy combat vehicle requirements. This engine features high power output in a compact design that is oil-cooled allowing for a significant reduction in radiator size. This design requires a lubricant which can survive a sump temperature of 160°C, for 300 hours with transient sump temperature surges to over 177°C. A comprehensive high temperature lubricant development program has been initiated to address the need for this new design. A modified Cummins 10 liter diesel engine was used to simulate the operating condition of this low heat rejection engine. The premium commercial lubricant that was tested survived only 58 hours before completely losing oxidative stability. Several of the experimental lubricants completed the 200-hour peak torque endurance test.

Data link interfaces are a very important part of the heavy duty vehicle industry; sharing information between subsystems is vital. SAE Recommended Practices J1708, J1587 and J1922 were developed to provide standards for proprietary communications, general information sharing, diagnostic definition and early powertrain controls. The industry realized, however, that these standards would not accomplish the ultimate goal-that of a high speed control and communications network. The development of more capable serial data communications for the heavy duty vehicle industry was prompted by the following: the desire of component suppliers to integrate subsystems for improved performance; the advancement of technology; customer expectations; and government regulations.

The Cummins A3.4-125 (rated 93 kW at 3600 rpm) has been developed to meet 1991 US and California light-heavy duty emission standards, replacing the Cummins 6AT3.4 (formerly Onan L634T-A). Compliance with the stringent particulate standard has been achieved by redesigning the combustion chamber, a systematic oil control program, and charge air cooling. The Ricardo Comet combustion chamber was modified to a downstream glowplug configuration. Oil control efforts addressed all sources of oil derived particulate. With charge air cooling, NOx emissions were reduced while improving fuel economy, torque output, altitude capability, and engine durability. THE CUMMINS A3.4-125 is an evolutionary development of the 1988-90 6AT3.4 engine. The development was driven primarily by 1991 US and California light-heavy duty emission standards, but also was the result of a policy of continuous product improvement. The Cummins A Series diesel engine family was conceived as the Onan L Series (1*).

This paper discusses the various process changes, engine improvements, and equipment evolution that have contributed to significant increases in test productivity for heavy duty engines over the past several years. It deals with the development of short test cycles, methods of diagnosing operating problems, methods of maintaining test accuracy and discusses systems for minimizing test equipment down time. Finally it presents historical overview of the changes as they occurred at Cummins Engine Company and how performance improved over that transition period.

A Cummins B55 in3 350 bhp heavy-duty, turbocharged diesel engine was tested in fully cooled and uncooled modes over the EPA transient emission test cycles for comparison of gaseous and particulate emissions. The results are presented at the same fuel injection timing and at similar NOx emission levels. Also, steady state emission measurements and analysis of real-time transient emission data of selected runs are discussed. The uncooled engine does not represent an adiabatic (insulated) engine in its emission characateristics, but may indicate some trends. It may be useful in identifying design and/or operating parameters that need optimization.

The ongoing need for improved fuel economy, longer engine life, lower emissions, and in some cases, increased power output makes lower charge air temperatures more desirable. In 1983, Cummins introduced the new BCIV engine at 400 H.P. (298 KW) with “Optimized Aftercooling”, and is now introducing this concept to its remaining 10 and 14 Litre premium diesel engines. This Tuned Low Flow Cooling design provides many advantages when compared to the other alternatives studied, which included air-to-air and systems incorporating two radiators. The selection process considered performance, durability, fuel economy, emissions, noise, investment, and total vehicle installed cost. Computer simulations and vehicle tests were used to determine performance for each charge air cooling alternative. The simulations were used to guide prototype development and the selection of production hardware.