Search Results

In general, automatic braking uses an electric stability control (ESC) hydraulic unit that can automatically increase the hydraulic pressure in the wheel cylinder (hereinafter called wheel pressure), independent of the driver’s braking operation. The hydraulic unit should have sufficient pressure response to apply autonomous emergency braking (AEB). It was necessary for the hydraulic unit to have a high flow rate for the pressure response. To satisfy the performance requirements of the AEB, a brushless motor, which has a high maximum rotational speed and good response, is adopted for the hydraulic unit. Furthermore, sensorless control, which does not require a rotation angle sensor, has been developed so that the motor size can be small and common to conventional units. The developed sensorless control can switch the driving methods in three states: pre-rotation, low speed, and high speed.

The set-off length (also referred to as the “lift-off length”) is reduced by the re-entrainment of the burned gas by the backward flow surrounding a diesel spray jet produced by a multi-hole nozzle. In the present study, to estimate the equivalence ratio at the set-off length, a means of estimating the amount of burned gas that is re-entrained into the near-nozzle region of the diesel spray jet was established. The results revealed that the suppression of soot formation in quasi-steady diesel spray flames produced by a multi-hole nozzle and a high injection pressure is not attained by reducing the equivalence ratio at the set-off length. Analysis of the amount of soot along the spray axis using a two-color method revealed that the maximum soot amount position appears in a quasi-steady spray flame, after the collapse of the head vortex in which a dense soot cloud is formed. The maximum soot amount position does not change even if the injection pressure varies.

The purpose of this study is to elucidate flame propagation behavior of homogeneous propane-air mixture under application of non-uniform electric field. A needle-shaped electrode was attached to the ceiling and a plate electrode was set at bottom of combustion chamber, so that the electric field was applied in the direction of the chamber's vertical axis. A homogeneous propane-air mixture was supplied at equivalence ratio of 1.0 and was ignited by leaser induced breakdown under atmospheric pressure and room temperature. It was found that the flame front and plate electrode were repelled each other and a thin air layer was formed between the flame and plate electrode when a relatively low positive DC non-uniform electric field was applied to the needle-shaped electrode. It might be thought that the induced current was generated in the flame front, so that the flame front and plate electrode repelled each other.

A response surface model of a diesel spray, parameterized by the internal geometries of a nozzle, is established in order to design the nozzle geometries optimally for spray mixing. The explanatory variables are the number of holes, the hole diameter, the inclined angle, the hole length, the hole inlet radius, K-factor and the sac diameter. The model is defined as a full second-order polynomial model including all the first-order interactions of the variables, and a total of 40 sets of numerical simulations based on D-optimal design are carried out to calculate the partial regression coefficients. Partial regression coefficients that deteriorate the estimate accuracy are eliminated by a validation process, so that the estimate accuracy is improved to be ±3% and ±15% for the spray penetration and the spread, respectively. Then, the model is applied to an optimization of the internal geometries for the spray penetration and the spray spread through a multi-objective genetic algorism.

At present, various efforts are being made in the industrial world to preserve the earth's environment. Automobile industry has to comply with the emission control regulations including NOx and PM and the requirement of reducing CO2 emission from the viewpoint of global warming protection and energy saving. In these situations, diesel engines having a high potential to reduce CO2 emission are attracting much attention. In order to enhance the potential of diesel to reduce CO2 while solving its problems (“slow, dirty, noisy”), common rail systems are vital. DENSO developed an advanced common rail system (CRS) that integrates fuel injectors capable of delivering up to five injection events per combustion cycle at 180MPa injection pressure. This paper describes the injection performance and effects of the 180MPa common rail system and then explains the next generation common rail system.

Many ICs are used in various electronic components in automotive applications, such as ECUs (electronic control units) and smart actuators. Automotive ICs required the following features: (1) high integration of analog, digital and output devices; (2) high breakdown voltage for analog devices standing the battery voltage; (3) highly accurate control for analog circuits; (4) susceptibility under harsh operating conditions, such as high ambient temperature and high humidity; and (5) high surge immunity such as ESD (electrostatic discharge) robustness. To meet these requirements, we developed analog and output devices with improved surge endurance based on SOI wafer and trench-dielectric-isolation technologies. Analog circuit applications, especially accurate power management or high-precision solenoid driving, demands stable temperature-compensated output. Load dump and battery-jumping also needs high voltage protection and high noise immunity for these devices.

Carbon brushes for automotive starters are used under severe conditions of high electric current density, high contact pressure and high sliding velocity. Therefore lead has traditionally been added to brushes to improve performance and durability. Lead is an environmental hazardous substance. In the EU, the law prohibits adding lead to brushes for electric motors which is installed on new automobiles in and after January 2005. In order to develop the lead free carbon brush for starters, we analyzed the effect and selected substitutive substance of lead. Adding lead to the brush reduces the electric resistance increase of the brush in high-temperature and high-humidity atmosphere and in high-temperature atmosphere. Furthermore lead reduces the wear amount of brush. We developed the lead free brush surpassing the lead addition brush in performance and durability by addition of lead alternatives silver and zinc.

A DPNR (Diesel Particulate-Nox Reduction) system is designed to simultaneously remove PM (Particulate Matter) and NOx from the exhaust of diesel engined vehicles. A DPF (Diesel Particulate Filter) is used in the DPNR system to reduce the PM. The DPF must have high PM filtering efficiency, while at the same time having low back pressure. However, filtering efficiency and back pressure have trade off relations. Therefore, it is necessary to optimize the pore distribution in the walls of the DPF to satisfy both characteristics. This paper will explain that optimized control of pore distribution enables both high PM filtering efficiency and low back pressure.

Spark plugs with higher ignitability are continuously in great demand to realize high fuel efficiency and low emissions. To meet this demand, DENSO launched the Iridium Spark Plug in 1997, which realized the two characteristics that had been conventionally difficult to achieve concurrently-high ignitability and long life. The development of this product was enabled by miniaturizing the center electrode, produced using DENSO's original, highly wear-resistant iridium alloy (featuring a high melting point and excellent oxidation resistance). While spark plugs are now required to have a longer service life, they are also required to be higher in ignitability, as exhaust gas regulations have been tightened recently. However, the effort to miniaturize the center electrode is reaching a limit.

In a conventional soldering process, solvents, such as chlorofluorocarbons (CFCs), have been necessary to remove the flux-residue after soldering. A new CFC-free fluxless soldering process has been developed to obtain high sealing ability even in a small soldering area. This new process utilizes a reducing atmosphere with an appropriate load and assembly orientation to solder the parts. Under this fluxless condition, it is found that appropriate loading and good solder-wettability of the upper part increase the wettability of the lower part.