Search Results

The objective of this study was to investigate the change of relative local velocity in each pulley groove at sliding between the belt and pulleys for a metal-pushing V-belt type CVT where micro elastic slips were inevitably accompanied to transmit power, while the transmissions were widely adopted to provide comfortable driving by continuously automatically adjusting the speed ratio. Local changes of wrapping radial position and velocity of the belt in each pulley groove of the CVT were simultaneously measured by a potentiometer with a spinning roller in the experiments. The mechanical power generated by the AC motor was transmitted through the CVT unit from the driving axis to the driven axis as usual under practical conditions while the speed ratio was set to 1.0. Pulley clamping force was applied by oil pressure.

The tire is one of the most important parts, which influence the noise, vibration, and harshness of the passenger cars. It is well known that effect of rotation influences tire vibration characteristics, and earlier studies presented formulas of tire vibration behavior. However, there are no studies of tire vibration including lateral vibration on effect of rotation. In this paper, we present new formulas of tire vibration on effect of rotation using a three-dimensional flexible ring model. The model consists of the cylindrical ring represents the tread and the springs represent the sidewall stiffness. The equation of motion of lateral, longitudinal, and radial vibration on the tread are derived based on the assumption of inextensional deformation. Many of the associated numerical parameters are identified from experimental tests.

In this research, we aim at the construction of a steering cooperation-type front-wheel steering control system to reduce the rider's steering load by stabilizing the behavior of the motorcycle when turbulence in the direction of a roll occurs during low-speed driving. Finally, a front-wheel steering control system that considers cooperation with a rider's steering based on the experimental result is constructed, and the utility is verified by simulation.

The purpose of this study is to characterize the brake torque variation (BTV) of the developed brake system using wave type brake disc. The brake torque was fluctuated when the pad passed at the point of the wavy shape. The indentation of the pad into the space of wavy shape was observed. These results indicate that remarkable peak of the BTV of the wave type brake disc was related with the pad deformation. In the devised test, remarkable peak of the BTV of the wave type brake disc was decreased by insertion of spacers. This paper proposed an effective aspect to prevent the BTV of the wave type brake disc.

Improvement of vehicle interior noise is desired in recent years in the modern world of the demand of low weight, good fuel economy and offering technical advantages strongly. The dynamic force transmission of rolling tires from the road surface to the spindles is a critical factor in vehicle interior noise. We focus on structure-borne noise transferred through the spindle. It is necessary for effort of the effective tire/road noise reduction to predict spindle force excited by tire/road contact. The major issues in predicting spindle forces are to clarify the distribution of road forces and how to input on the simulation model. Therefore, it is important that road forces are measured accurately on the rolling tire. First, the dynamic road forces on the rolling tire are measured by using the tri-axial force sensor directly. In efforts to reduce interior noise due to structure-borne noise, it is necessary to predict spindle forces excited by the tire/road contact.

The demand for quieter vehicle interiors increases year after year. The dynamic force transmission of rolling tires from the road surface to the spindles is a critical factor in vehicle interior noise. We investigated the dynamic force transmission of a rolling tire as it relates to reducing vehicle interior noise. A test with a tire rolling over a cleat was conducted in order to measure the road forces and the spindle forces. The transfer function of the rolling tire was identified from the experimental results by applying multi dimensional spectral analysis. In addition, Computer Aided Engineering (CAE) technology has advanced recently. This enables prediction of spindle forces early in the design stage. One of the most important issues in predicting spindle forces accurately is to clarify the distribution of road forces. This paper also describes the distribution of the dynamic road forces of the rolling tire.

A hydraulic excavator cab is mounted on a viscous mount. When the weight of the cab is heavy, the neutral position is depressed. Besides, at a large load, the cab receives compressive repulsion power of oil thereby restricting its damping ability. In addition, it is difficult to obtain an arbitrary damping performance separately. To overcome these problems, which combines the shear force due to viscous fluid with elastic force due to air-spring a mount, was invented. The neutral position of composite mount is adjustable by air-spring according to the weight. And viscous oil is not sealed up. So, viscous oil can flow at a large load. Therefore, it may not experience the repulsion force of oil in spite of a large load. Moreover, the generated elastic force is adjustable according to change of pressure in the air spring, and the generated damping force is adjustable according to change of viscous fluid's viscosity or volume.

This study discussed the mechanism of the low speed judder for wave type brake disc developed newly for recent motorcycles. Wavy disc was examined to investigate the effect of wave configurations on the BTV (Brake Torque Variation) behavior. Torque amplitude in braking was compared with respect to the revolution order which represented the multiple number of the number of revolutions. To explain the mechanism at the mode showing largest BTV, the elastic deformation of the pad was analyzed by finite element method concerning geometrical nonlinearity with commercial code. This study found that most crucial BTV appeared on low speed judder was observed at the 3 rd peaks on the revolution order. Test data showed that this crucial BTV was related with the number of waves at the disc periphery, and caused by the indentation of the pad into notched part at disc periphery.

A prediction method was proposed for crack initiation in one-piece type brake discs under extreme braking conditions. Braking tests under extreme loading conditions were conducted by using sample discs. The variations of internal temperatures and surface strains at several locations were measured by using thermocouples and strain gages. In order to obtain the S-N curve of the disc material, specimens with a hole in their center were used for the fatigue test in which an alternative strain was cyclically applied. The numbers of strain cycles, when a 0.3mm crack initiated from the hole, were analyzed by the Weibull plot. The maximum and minimum strains at the hole edge were estimated by calculation considering the temperature variation with respect to time as well as the strain induced by friction due to braking pads. The number of cycles corresponding to the strain amplitude range was estimated by the rain-flow method.

To reduce tire/road noise, it is important to examine the noise generation mechanism. Noise generated by a rolling tire is mainly emitted from the tread block. However, it has recently been reported that smooth tires also generate noise recently. This paper remarks on a smooth tire vibration by rolling on the road. The vibration of a rolling smooth tire is mainly vibration excited from the road surface. It is difficult to measure the input from the road surface, so we measured the tire's vibration at the leading and trailing edges. Scan Laser Doppler Vibrometers were employed to measure the vibration of the tire tread.

This paper describes a steady vibration of an engine supported by rubber and hydraulic mounts at a relatively low frequency range, assuming an engine is a rigid body. We identify dynamic characteristics of a hydraulic mount with respect to frequency and amplitude. The equation of motion is solved numerically by the Newton-Raphson method, treating the mount characteristics as functions of frequency and amplitude. The excitation test to simulate an engine shake and an idling vibration was performed using a mass block instead of an actual engine. During the engine shake, we observed that the amplitude dependency of hydraulic mounts strongly influences the vibration, while idling, we investigated rolling vibration especially for the case where the torque axis does not pass through the engine's center of gravity. The theoretical predictions agree closely with the experimental results in both engine shake and idling vibration tests.

Tiny (hair-like) cracks initiated around small holes in the flange of one-piece brake discs were observed at an overloading condition. Thermally induced cyclic stress strongly affects the crack initiation in the brake discs. In order to show the crack initiation mechanism, the temperature distribution at the flange was firstly measured. The temperature distribution under overloading was analyzed by using the finite element method. Based on the experimental and calculated results, the crack initiation mechanism for one-piece brake discs at the very severe braking condition was explained. In addition, the effective methods are suggested for reducing the initiation of tiny cracks around the holes.

Generally, it is well known that road noise generated by vibration from automobile tires and suspensions can be reduced by changing the stiffness of the rubber mounts installed in the suspension systems. Such stiffness, however, is rarely changed to avoid riding discomfort and so on. In this paper, a stiffness optimization method for suspension system rubber mounts that reduces road noise, and improves riding comfort as well, is presented. In the process, Road Noise Contribution Analysis (RNCA) is applied to the target vehicle to specify the major factors of road noise. Furthermore, the suspension system of the vehicle is investigated by Sensitivity Analysis using Measured FRF data (SAMF) to identify the optimal stiffness combination of rubber mounts. As a result, an effective stiffness combination of two mounts is specified to reduce road noise and to improve riding comfort.

A new discrete model was developed in order to analyze the power transmitting mechanisms of a dry hybrid V-belt CVT not only at steady states but also at transitional states where the speed ratio was changing. Block tilting in the pulley was considered in the advanced numerical model as well as pulley deformation due to pulley thrust. The validity of the present model was well confirmed by comparing the calculated results on transmitting and normal forces with the former experimental results. The calculated results showed that both block tilting and pulley deformation meaningfully affected the pulley thrust ratio between the driving and the driven pulleys.

An advanced numerical model is proposed to analyze the power transmitting mechanisms of a CVT using a metal V-belt. By using the present model, forces acting on the belt are well estimated not only at steady states but also during transitional states where the speed ratio is changing. The numerical results show that blocks are in compression in both strands when the speed ratio is rapidly shifted. A complementary model is also developed to analyze the load distribution among bands which form the ring. The load distribution in the ring is governed by the difference in coefficients of friction among elements.