Search Results

Spark ignition engines utilize catalytic converters to reform harmful exhaust gas emissions such as carbon monoxide, unburned hydrocarbons, and oxides of nitrogen into less harmful products. Aftertreatment devices require the use of expensive catalytic metals such as platinum, palladium, and rhodium. Meanwhile, tightening automotive emissions regulations globally necessitate the development of high-performance exhaust gas catalysts. So, automotive manufactures must balance maximizing catalyst performance while minimizing production costs. There are thousands of different recipes for catalytic converters, with each having a different effect on the various catalytic chemical reactions which impact the resultant tailpipe gas composition. In the development of catalytic converters, simulation models are often used to reduce the need for physical parts and testing, thus saving significant time and money.

Cooling airflow is an essential factor when it comes to vehicle performance and operating safety. In recent years, significant efforts have been made to maximize the flow efficiency through the heat exchangers in the under-hood compartment. Grille shutters, new fan shapes, better sealings are only some examples of innovations in this field of work. Underhood cooling airflow simulations are an integral part of the vehicle development process. Especially in the early development phase, where no test data is available to verify the cooling performance of the vehicle, computational fluid dynamics simulations (CFD) can be a valuable tool to identify the lack of fan performance and to develop the appropriate strategy to achieve airflow goals through the heat exchangers. For vehicles with heat exchangers in the underhood section the airflow through those components is of particular interest.

The LEV IV FTP PM limit in the recently approved CARB ACC II regulations for passenger cars and light duty trucks will be 1 mg/mile starting in 2025. Gravimetric PM measurement at these levels is very challenging as the net mass of PM on the filter in full flow tunnel testing ranges between 8 to 32 micrograms depending on amount of dilution. This is approaching tunnel background levels which, in combination with filter handling, static charge removal and microbalance instability, compounds the uncertainty. One major source of the uncertainty at these low levels is the tunnel contamination resulting in high variability from test to test and cell to cell. This tunnel background is mostly HC artifact which cannot be easily controlled and can be significantly higher than the 5-μg CFR allowable correction limit in some test cells.

A large amount of heat is generated in electric vehicle battery packs during high rate charging, resulting in the need for effective cooling methods. In this paper, a prototype liquid cooled large format Lithium-ion battery module is modeled and tested. Experiments are conducted on the module, which includes 31Ah NMC/Graphite pouch battery cells sandwiched by a foam thermal pad and heat sinks on both sides. The module is instrumented with twenty T-type thermocouples to measure thermal characteristics including the cell and foam surface temperature, heat flux distribution, and the heat generation from batteries under up to 5C rate ultra-fast charging. Constant power loss tests are also performed in which battery loss can be directly measured.

In the light duty diesel segment, the need persists for an advanced control system to monitor the health of an aftertreatment system throughout a vehicle’s life in order to maintain compliance with ever tightening emissions levels. In on-board diagnostics (OBD), every diagnostic is validated during development stages to detect when a system under monitoring of that diagnostic has failed. This necessitates the need to create parts which represent a failure that would be observed on the vehicle. These failed parts, referred to as limit or threshold parts, are developed through a limit part creation process. Although there are commonalities amongst Original Equipment Manufacturers (OEM), each OEM has their own detection logic which will require a unique and specific limit part. Various methods exist for creating these limit parts, and each method produces a different combination of ability to detect the failure and its associated tailpipe emissions.

Stringent requirements for high fuel economy and energy efficiency mandate using increasingly complex vehicle thermal systems in most types of electrified vehicles (xEVs). Enabling the maximum benefits of such complex thermal systems under the full envelope of their operating modes demands designing complex thermal control systems. This is becoming one of the most challenging problems for electrified vehicles. Typically, the thermal systems of such vehicles have several modes of operation, constituting nonlinear multiple-input/multiple-output (MIMO) dynamic systems that cannot be efficiently controlled using classical or rule based strategies. This paper covers the different steps towards the design of a model-based control (MBC) strategy that can improve the overall performance of xEV thermal control systems. To achieve the above objective, the latter MBC strategy is applied to control cooling of the cabin and high voltage battery.

Autoignition delay times of two full blend gasoline fuels (high and low RON) were explored in a rapid compression machine. CO2 dilution by mass was introduced at 0%, 15%, and 30% levels with the O2:N2 mole ratio fixed at 1:3.76. This dilution strategy is used to represent exhaust gas recirculation (EGR) substitution in spark ignition (SI) engines by using CO2 as a surrogate for major EGR constituents(N2, CO2, H2O). Experiments were conducted over the temperature range of 650K-900K and at 10 bar and 20 bar compressed pressure conditions for equivalence ratios of (Φ =) 0.6-1.3. The full blend fuels were admitted directly into the combustion chamber for mixture preparation using the direct test chamber (DTC) approach. CO2 addition retarded the autoignition times for the fuels studied here. The retarding effect of the CO2 dilution was more pronounced in the NTC region when compared to the lower and higher temperature range.

This paper focuses on the conjugate heat transfer analysis of an I4 engine, and discusses optimization of the coolant passages in engine coolant jackets. Direct Optimization approach integrates an optimizer with the numerical solver. This method of optimization is compared with a metamodel-based optimization in which a metamodel is generated to aid in finding an optimal design. The direct optimization and metamodel approaches are compared in terms of their accuracy, and execution time.

The Press-in-Place (PIP) gasket is a static face seal with self-retaining feature, which is used for the mating surfaces of engine components to maintain the reliability of the closed system under various operating conditions. Its design allows it to provide enough contact pressure to seal the internal fluid as well as prevent mechanical failures. Insufficient sealing pressure will lead to fluid leakage, consequently resulting in engine failures. A test fixture was designed to simulate the clamp load and internal pressure condition on a gasket bolted joint. A sensor pad in combination with TEKSCAN equipment was used to capture the overall and local pressure distribution of the PIP gasket under various engine loading conditions. Then, the test results were compared with simulated results from computer models. Through the comparisons, it was found that gasket sealing pressure of test data and CAE data shows good correlations in all internal pressure cases when the bolt load was 500 N.

The reduction of automotive emissions is instrumental in the fight against air pollution and its impact on global warming. This realization has empowered governments around the world to mandate lower levels of vehicle emissions requiring the Original Equipment Manufacturers (OEMs) to implement advanced aftertreatment technologies in their applications. Achieving emission levels as low as SULEV30 or SULEV20 would have been impossible only a couple of decades ago, however, these lower levels of emissions are now a possibility through advanced control strategies and aftertreatment systems. As a part of this mandate to lower emissions, OEMs are also continuously monitoring the health and performance of their aftertreatment and control components. The implementation of On Board Diagnostics (OBD) ensures that control systems are functioning robustly and the emission levels are achieved and maintained to high mileages for the life of the vehicle.

Mixture formation and combustion dynamics are the primary contributors to the performance and emission characteristics of direct-injected spark ignition (SI) engines. This requires assessing the benefits and tradeoffs of the design and control factors that influence mixing and the subsequent combustion event. In this study, Taguchi's L18 orthogonal array design of experiment (DoE) methodology has been applied to assess contributions and tradeoffs of varied compression ratio, piston bowl design, intake port tumble design, injector spray pattern, injection timing, injection pressure, exhaust gas recirculation (EGR) rate, and intake valve closing timing in a single-cylinder boosted gasoline direct injection (GDI) SI engine. This multiparameter study has been carried out across three speed-load conditions representative of typical automotive application operating ranges.

In response to demands for higher fuel economy and stringent emission regulations, OEMs always strive hard to improve component/system efficiency and minimize losses. In the driveline system, improving the efficiency of an automotive rear-axle is critical because it is one of the major power-loss contributor. Optimum oil-fill inside an axle is one of the feasible solutions to minimize spin losses, while ensuring lubrication performance and heat-dissipation requirements. Thus, prior to conducting vehicle development tests, several dyno-level tests are conducted to study the thermal behavior of axle-oil (optimum level) under severe operating conditions. These test conditions represent the axle operation in hot weather conditions, steep grade, maximum tow capacity, etc. It is important to ensure that oil does not exceed its thermal limits (disintegration of oil leading to degradation).

The heat generated by an internal combustion engine must be dissipated to maintain acceptable component temperatures throughout the entire powertrain system under all operating conditions. However, under cold start conditions it is beneficial to retain this available heat to achieve faster warm-up in order to reduce fuel consumption. In modern engines there are several components in the coolant circuit that are used to accelerate the warm-up of sub-system fluids such as the engine oil, transmission oil and axle oil. The magnitude of the fuel consumption reduction will depend on how these rapid warm-up devices are arranged, combined and controlled. This paper describes a methodology that was developed to optimize the distribution of coolant heat in the powertrain system during warm-up. A comparative study can be performed to optimize the arrangement of each heat exchanger in any given powertrain system to minimize cost and time early in development.

With the demand of growing cooling requirements of fast charging and new thermal architecture design in battery electric vehicles, the automotive industry is exploring electric compressors of large displacement. Compared with small and mid-size (displacement less than 33 cc) compressor, large (34-44 cc) and extra-large (45 cc and above) compressor products are used. This paper investigates the compressor sizing effect for heat pump (HP) system of A-Segment and D-Segment battery electric vehicles. The system performance is evaluated with large (34 cc) and extra-large (57 cc) compressors by considering energy efficiency, cabin thermal management and battery fast charging use cases.

Thermal management of lithium-Ion battery (LIB) has become very critical issue in recent years. One of the challenges for the design and packaging of the battery is to maintain the battery temperature within acceptable ranges and also reduce temperature gradients within the battery cells. Controlling the battery temperature is essential for the battery performance and the long-term battery life. Increased difference between battery cell temperatures can lead to non-uniform charging and non-uniform ageing of battery cells. The purpose of this paper is to investigate available technologies using heat pipes as a means of improving battery thermal management. Several studies have been conducted regarding the effect of heat pipes on battery temperature. However, in this paper we present a comprehensive study of heat pipes effects through transient analysis of a complete vehicle thermal model.

Lead-acid batteries have been widely used in automotive applications. Extending battery life and reducing battery warranty requires reducing any deteriorating to battery internals and battery electrolyte. At the end of battery life, it is required to maintain at least 50% of its initial capacity [1,2]. The rate of battery degradation increases at high battery temperatures due to increased rate of electrochemical reactions and potential loss of battery electrolyte. For Lead-Acid batteries, an electrolyte solution consists of diluted sulfuric acid. Battery electrolyte/water loss affects battery performance. Water loss is caused by high internal battery temperature and gassing off due to battery electrochemistry. High temperatures, high charging rates, and over charging can cause a loss of electrolyte in non-sealed batteries. In sealed batteries, the same factors will cause an increase in temperature and pressure which can eventually result in the release of hydrogen and oxygen gases.

Advances in diesel engine and catalyst technologies have enabled light passenger vehicles in meeting the most stringent Tier 3/LEV III emission levels and durability requirements. The advancements in diesel aftertreatment catalyst technology have made catalysts more susceptible to low levels of impurities, typically referred to as poisons. Published studies over the last two decades, have shown a significant impact on the performance of catalysts, to the presence of sulfur and other inorganics in fuels and oils. The design of an aftertreatment system (ATS) typically sets limits for lubricant and fuel quality, specific to the geographical region and availability of certain level of regulated fuels. In this study, we investigate a real-world aged diesel vehicle which exhibited deterioration in tailpipe emissions, beyond levels targeted during engineering development.

This paper proposes a domain-centralized powertrain E/E (electrical and/or electronic) architecture for all-electric vehicles that features: a powerful master controller (domain controller) that implements most of the functionality of the domain; a set of smart actuators for electric motor(s), HV (High Voltage) battery pack, and thermal management; and a gateway that routes all hardware signals, including digital and analog I/O, and field bus signals between the domain controller and the rest of the vehicle that is outside of the domain. Major functional safety aspects of the architecture are presented and a safety architecture is proposed. The work represents an early E/E architecture proposal. In particular, detailed partitioning of software components over the domain’s Electronic Control Units (ECUs) has not been determined yet; instead, potential partitioning schemes are discussed.

Internal combustion engine gets heated up due to continuous combustion of fuel. To keep engine working efficiently and prevent components damage due to very high temperature, the engine needs to be cooled down. Based on power output requirement and provision for cooling system, every engine has it’s unique cooling system. Liquid based cooling systems are majorly implemented in automobile. It’s important to keep in mind that during design phase that, cooling the engine will lower the power to fuel consumption ratio. Therefore, during lower ambient conditions, the cooling system should be able to uniformly increase the temperature of the engine components, engine oil and transmission oil. This is achieved by circulating the coolant through cooling jacket, engine oil heater and transmission oil heater, which will be heated by the combustion heat.

Maintaining the fuel temperature and fuel system components below certain values is an important design objective. Predicting these temperatures is therefore one of the key parts of the vehicle’s thermal management process. One of the physical processes affecting fuel tank temperature is fuel vaporization, which is controlled by the vapor pressure in the tank, fuel composition and fuel temperature. Models are developed to enable the computation of the fuel temperature, fuel vaporization rate in the tank, fuel temperatures along the fuel supply lines, and follow its path to the charcoal canister and into the engine intake. For diesel fuel systems where a fuel return line is used to return excess fluid back to the fuel tank, an energy balance will be considered to calculate the heat added from the high-pressure pump and vehicle under-hood and underbody.