Search Results

Driving simulators allow the testing of driving functions, vehicle models and acceptance assessment at an early stage. For a real driving experience, it's necessary that all immersions are depicted as realistically as possible. When driving manually, the perceived haptic steering wheel torque plays a key role in conveying a realistic steering feel. To ensure this, complex multi-body systems are used with numerous of parameters that are difficult to identify. Therefore, this study shows a method how to generate a realistic steering feel with a nonlinear open-loop model which only contains significant parameters, particularly the friction of the steering gear. This is suitable for the steering feel in the most driving on-center area. Measurements from test benches and real test drives with an Electric Power Steering (EPS) were used for the Identification and Validation of the model.

Aeroacoustics is important in the automotive industry, as it significantly influences driving comfort. Particularly in the case of battery electric vehicles (BEVs), the flow noise is already crucial at lower driving speeds, since these generate barely any drive noise and the masking effects produced by the engine are eliminated. Due to the increasing importance of drag minimization and elimination of the exhaust system, the underbody of BEVs is typically very streamlined and exhibits a low acoustic interference potential. However, even small geometric modifications to the vehicle can lead to changes in the flow around the vehicle and consequently to significant noise sources. Thus, significant flow resonances in the low frequency range below 30 Hz have been detected on certain vehicle configurations. Initial investigations have shown that the flow around the front wheel spoilers is relevant for the development of the flow phenomenon.

This paper contributes to the Committee on Commonized Aerodynamics Automotive Testing Standards (CAATS) initiative, established by the late Gary Elfstrom. It is collaboratively compiled by automotive wind tunnel users and operators within the Subsonic Aerodynamic Testing Association (SATA). Its specific focus lies in automotive wind tunnel test techniques, encompassing both those relevant to passenger car and race car development. It is part of the comprehensive CAATS series, which addresses not only test techniques but also wind tunnel calibration, uncertainty analysis, and wind tunnel correction methods. The core objective of this paper is to furnish comprehensive guidelines for wind tunnel testing and associated techniques. It begins by elucidating the initial wind tunnel setup and vehicle arrangement within it.

Dust testing of vehicles on unpaved roads is crucial in the development process for automotive manufacturers. These tests aim to ensure the functionality of locking systems in dusty conditions, minimize dust concentration inside the vehicle, and enhance customer comfort by preventing dust accumulation on the car body. Additionally, deposition on safety-critical parts, such as windshields and sensors, can pose threats to driver vision and autonomous driving capabilities. Currently, dust tests are primarily conducted experimentally at proving grounds. In order to gain early insights and reduce the need for costly physical tests, numerical simulations are becoming a promising alternative. Although simulations of vehicle contamination by dry dust have been studied in the past, they have often lacked detailed models for tire dust resuspension. In addition, few publications address the specifics of dust deposition on vehicles, especially in areas such as door gaps and locks.

The improvement of vehicle soiling behavior has increasing interest over the past few years not only to satisfy customer requirements and ensure a good visibility of the surrounding traffic but also for autonomous vehicles, for which soiling investigation and improvement are even more important due to the demands of the cleanliness and induced functionality of the corresponding sensors. The main task is the improvement of the soiling behavior, i.e., reduction or even prevention of soiling of specific surfaces, for example, windows, mirrors, and sensors. This is mostly done in late stages of vehicle development and performed by experiments, e.g., wind tunnel tests, which are supplemented by simulation at an early development stage. Among other sources, the foreign soiling on the side mirror and the side window depend on the droplet detaching from the side mirror housing.

There is a growing need for low-emissions concepts due to stricter emission regulations, more stringent homologation cycles, and the possibility of a ban on new engines by 2035. Of particular concern are the conditions during a cold start, when the Three-Way Catalyst is not yet heated to its light-off temperature. During this period, the catalyst remains inactive, thereby failing to convert pollutants. Reducing the time needed to reach this temperature is crucial to comply with the more stringent emissions standards. The post oxidation by means of secondary air injection, illustrated in this work, is a possible solution to reduce the time needed to reach the above-mentioned temperature. The strategy consists of injecting air into the exhaust manifold via secondary air injectors to oxidize unburned fuel that comes from a rich combustion within the cylinder.

The aeroacoustic development of vehicles is still mainly carried out in wind tunnels under steady flow conditions, although the real situation is different. However, as discussed in several earlier publications, a vehicle experiences unsteady, turbulent flow on road, which results for example from natural wind, wakes of other vehicles, or obstacles at the roadside in combination with side wind. The resulting temporal variations of the wind noise inside the cabin affect the passengers’ comfort and safety through fatigue. To be able to also consider the unsteady aeroacoustics in the vehicle development process, a comprehensive method has been developed that is presented in full for the first time in this paper. The on-road situation is simulated in a realistic and reproducible manner in the full-scale wind tunnel of the University of Stuttgart by means of an active turbulence generator, developed by FKFS.

Numerical methodologies for aeroacoustic analyses are increasingly crucial for car manufacturers to optimize the effectiveness of vehicle development. In the present work, a hybrid numerical tool based on the combination of a delayed detached-eddy simulation and a finite element model, which relies on the Lighthill’s acoustic analogy and the acoustic perturbation equations, is presented. The computational aeroacoustics is performed by the software OpenFOAM and Actran, concerning respectively the CFD and the FEM. The aeroacoustic behavior of the SUV Lamborghini Urus at a cruising speed of 140 km/h has been investigated. The main aerodynamic noise phenomena occurring in the side mirror region in a frequency range up to 5 kHz are discussed. The numerical simulations have been verified against the measurements performed in the aeroacoustic wind tunnel of the University of Stuttgart, operated by FKFS.

Dry dust testing of vehicles on unpaved dust roads plays a crucial role in the development process of automotive manufacturers. One of the central aspects of the test procedure is ensuring the functionality of locking systems in the case of dust ingress and keeping the dust below a certain concentration level inside the vehicle. Another aspect is the customer comfort because of dust deposited on the surface of the car body. This also poses a safety risk to customers when the dust settles on safety-critical parts such as windshields and obstructs the driver’s view. Dust deposition on sensors is also safety critical and is becoming more important because of the increasing amount of sensors for autonomous driving. Nowadays, dust tests are conducted experimentally at dust proving grounds. To gain early insights and avoid costly physical testing, numerical simulations are considered a promising approach. Simulations of vehicle contamination by dry dust have been studied in the past.

A computational study of the vehicle aerodynamics influenced by the wake of the rotating wheel taking into account a detailed rim geometry is presently performed. The car configuration corresponds to a full-scale (1:1) notchback configuration of the well-known ‘DrivAer’ vehicle model, Heft et al. [1]. The objective of the present work is to investigate the performance of some popular turbulence models in conjunction with different methods for handling the wheel rotation – rotating wall velocity, ‘multiple reference frame’ and ‘sliding grid algorithm’. The specific focus hereby is on a near-wall RANS eddy-viscosity model based on elliptic-relaxation, sensitized to resolve fluctuating turbulence by introducing a specifically modeled production term in the scale-supplying equation, motivated by the Scale-Adaptive Simulation approach (SAS, [2]), proposed by Krumbein et al. [3].

The accelerated processes in vehicle development require new technologies for function development and validation. With this motivation, Function-in-the-Loop (FiL) simulation was developed as a link between Software-in-the-Loop (SiL) and Hardware-in-the-Loop (HiL) simulation. The combination of real Electronic Control Unit (ECU) hardware and software in conjunction with virtual components is very well suited for function development and testing. This approach opens up new possibilities for mechatronic systems that would otherwise require special test benches. For this reason, an Electric Power Steering (EPS) was transferred to a virtual environment using FiL simulation. This enables a wide range of applications, from EPS testing to the development of connected driving functions on an integrated platform. Right from the early development phases, the technology can be used purposefully with short integration cycles.

The investigation of vehicle soiling by improvement of vehicle parts to optimize the surrounding airflow is of great importance not only because of the visibility through windows and at mirrors but also the functionality of different types of sensors (camera, lidar, radars, etc.) for the driver assistance systems and especially for autonomous driving vehicles has to be guaranteed. These investigations and corresponding developments ideally take place in the early vehicle development process since later changes are difficult to apply in the vehicle production process for many reasons. Vehicle soiling is divided into foreign soiling and self-soiling with respect to the source of the soiling water, e.g., direct rain impact, swirled (dirty) water of other road users and own rotating wheels. The investigations of the soiling behavior of vehicles were performed experimentally in a wind tunnel and street tests.

The new CO2 and emissions limits imposed to European manufacturers require the adoption of different innovative solutions, such as the use of potentially CO2-neutral synthetic fuels alongside a tailored development of the internal combustion engine, as an excellent solution to accompany the hybridization of vehicles. Dr.Ing. h.c. F. Porsche AG and FKFS, already partners for the development of engines with eFuels, propose a new study carried out on a research engine, investigating the combination of Porsche synthetic gasoline (POSYN) with an engine with millerization and passive pre-chamber. The use of CO2-neutral fuels allow for an immediate reduction in CO2 emissions from all cars already on the market, particularly since Porsche is one of the manufacturers whose cars remain in use for the longest time. The data collected on a single-cylinder engine test bench, for different fuels, with conventional spark plug are used as input for the calibration of 3D-CFD simulations.

Automotive engineers use the wind tunnel to improve a vehicle’s aerodynamic properties on the road. However, a car driving on the road does not experience the steady-state, uniform flow characteristic of the wind tunnel. Wind, terrain and traffic all cause the flow experienced by the vehicle to be highly transient. Therefore, it is imperative to understand the effects of forces acting on the vehicle resulting from unsteady flow. To this end, the FKFS swing® installed in the University of Stuttgart’s model scale wind tunnel was used to create 36 different incident flow signals with time-resolved yaw angles. The cD values of five different 25% vehicle models, each with a notchback and a squareback configuration, were measured while under the influence of the aforementioned signals. The vehicle models were chosen to ensure a variety of different geometries, but at the same time also to enable isolated comparison of specific geometric properties.

The increasingly stringent targets for the automotive industry towards sustainability are being addressed not only with the improvement of engine efficiency, but also with growing research about alternative, synthetic, and CO2-neutral fuels. These fuels are produced using renewable energy sources, with the goal of making them CO2-neutral and also to reduce a significant amount of engine emissions, especially particulate matter (PM) and total hydrocarbon (THC). The objective of this work is to study the behavior and the potential of an eFuel developed by Porsche, called POSYN (POrscheSYNthetic) and to compare it with a standard gasoline.

For the regeneration of the Lean NOx Trap (LNT) a rich air-to-fuel ratio must be generated. This operation is very critical and has low combustion stability, especially in low load operation. A certain minimum engine load is always required for the regeneration phase. In the Real Driving Emissions this minimum engine load can be undercut over a long period of time. Hence, a reliable regeneration phase is not possible. The aim of these investigations is to extend the engine map range in which regeneration is possible towards lower loads. This is done by means of a variable valve train with second exhaust valve lift, which increases the internal residual gas amount. This in turns increases the temperature at start of combustion in the cylinder. Especially at low load and low combustion stability this leads to a stabilization of the combustion process. This advantage in combustion stability can be used for a reduction of the minimum engine load.

The wind tunnel is the standard tool in the development and improvement of vehicle aerodynamics. Usually, automotive wind tunnels contain an open test section, which results in a shear layer developing on the edge of the jet. This shear layer brings instabilities that can lead to resonance effects in the wind tunnel influencing the pressure distribution in the test section. To investigate the resonance effects, the classic wind tunnel corrections were applied to averaged drag measurements recorded in a resonance and nonresonance configuration of the model scale wind tunnel of the University of Stuttgart. The Mercker-Wiedemann-Method shows good compensation for the differing pressure gradients. Pressure measurements on the surface of the DrivAer Notchback model show different separation points on the rear window for measurements in resonance and nonresonance configuration. This means that the resonance effects can influence the separation significantly.

To date, no generally valid statements can be made about the service life of brake pads, which may be due to factors such as driving style, the friction material used or the varying vehicle weight. While dynamic friction models including friction history are already established [1], the investigation of wear and wear dust behavior is currently in the focus of many research projects. One example is the investigation of calculation models for brake pad wear while neglecting the temperature development in the brake [2]. In cars, temperatures of up to 800°C occur in the brake under high loads, which leads to a significant increase in wear. Accordingly, the question arises how an estimation of brake pad wear can be applied to highly dynamic load cases. To do this, however, the processes taking place in the boundary layer between pad and disc must first be comprehensively understood and described.

The increase in efficiency is the focus of current engine development by adopting different technologies. One limiting factor for the rise of SI-engine efficiency is the onset of knock, which can be mitigated by improving the combustion process. HCCI/SACI represent sophisticated combustion techniques that investigate the employment of pre-chamber with lean combustion, but the effective use of them in a wide range of the engine map, by fulfilling at the same time the need of fast load control are still limiting their adoption for series engine. For these reasons, the technologies for improving the characteristics of a standard combustion process are still largely investigated. Among these, water injection, in combination with the Miller cycle, offers the possibility to increase the knock resistance, which in turn enables the rise of the engine geometric compression ratio.

The reliability of electronic components is of increasing importance for further progress towards automated driving. Thermal aging processes such as electromigration is one factor that can negatively affect the reliability of electronics. The resulting failures depend on the thermal load of the components within the vehicle lifetime - called temperature collective - which is described by the temperature frequency distribution of the components. At present, endurance testing data are used to examine the temperature collective for electronic components in the late development stage. The use of numerical simulation tools within Vehicle Thermal Management (VTM) enables lifetime thermal prediction in the early development stage, but also represents challenges for the current VTM processes [1, 2]. Due to the changing focus from the underhood to numerous electronic compartments in vehicles, the number of simulation models has steadily increased.