Search Results

Hands-free phone use is the most utilized use case for vehicles equipped with infotainment systems with external microphones that support connection to phones and implement speech recognition. Critically then, achieving hands-free phone call quality in a vehicle is problematic due to the extremely noisy nature of the vehicle environment. Noise generated by wind, mechanical and structural, tire to road, passengers, engine/exhaust, HVAC air pressure and flow are all significant contributors and sources of noise. Other factors influencing the quality of the phone call include microphone placement, cabin acoustics, seat position of the talker, noise reduction of the hands-free system, etc. This paper describes the work done to develop procedures and metrics to quantify the effects that influence the hands-free phone call quality.

The Multi Material Lightweight Vehicle (MMLV) developed by Magna International and Ford Motor Company is a result of a US Department of Energy project DE-EE0005574. The project demonstrates the lightweighting potential of a five passenger sedan, while maintaining vehicle performance and occupant safety. Prototype vehicles were manufactured and limited full vehicle testing was conducted. The Mach-I vehicle design, comprised of commercially available materials and production processes, achieved a 364kg (23.5%) full vehicle mass reduction, enabling the application of a 1.0-liter three-cylinder engine resulting in a significant environmental benefit and fuel reduction. This paper reviews the mass reduction and structural performance of aluminum, magnesium, and steel components for a lightweight multi material door design for a C/D segment passenger vehicle. Stiffness, durability, and crash requirements are assessed.

Cold idle operation of a modern design light duty diesel engine and the effect of multiple pilot injections on stability were investigated. The investigation was initially carried out experimentally at 1000rpm and at −20°C. Benefits of mixture preparation were initially explored by a heat release analysis. Kiva 3v was then used to model the effect of multiple pilots on in-cylinder mixture distribution. A 60° sector of mesh was used taking advantage of rotational symmetry. The combustion system and injector arrangements mimic the HPCR diesel engine used in the experimental investigation. The CFD analysis covers evolutions from intake valve closing to start of combustion. The number of injections was varied from 1 to 4, but the total fuel injected was kept constant at 17mm3/stroke. Start of main injection timing was fixed at 7.5°BTDC.

Available methodologies for model bias identification are mainly regression-based approaches, such as Gaussian process, Bayesian inference-based models and so on. Accuracy and efficiency of these methodologies may degrade for characterizing the model bias when more system inputs are considered in the prediction model due to the curse of dimensionality for regression-based approaches. This paper proposes a copula-based approach for model bias identification without suffering the curse of dimensionality. The main idea is to build general statistical relationships between the model bias and the model prediction including all system inputs using copulas so that possible model bias distributions can be effectively identified at any new design configurations of the system. Two engineering case studies whose dimensionalities range from medium to high will be employed to demonstrate the effectiveness of the copula-based approach.

In an effort to reduce the cost and time associated with bench level automotive electrical and electromagnetic compatibility (EMC) validation tests, a survey was created to request advice from the test labs that perform this testing. The survey focuses particularly on the development of the test plan document and the preparation of the test setup. The survey was sent to a targeted group of individuals with experience in performing this type of testing. The invitees work at laboratories that represent the majority of labs in the world that are authorized to perform component electrical / EMC validation testing for automotive original equipment manufacturers (OEMs). There were a significant number of responses; it is possible that representatives from all of the invited laboratories responded. The survey results provide demographic information about the test labs and their participants.

The objectives of this study were a) to determine how expert judges categorized valid Integrated Vehicle-Based Safety Systems (IVBSS) Forward Collision Warning (FCW) events from review of naturalistic driving data; and b) to determine how consistent these categorizations were across the judges working in pairs. FCW event data were gathered from 108 drivers who drove instrumented vehicles for 6 weeks each. The data included video of the driver and road scene ahead, beside, and behind the vehicle; audio of the FCW alert onset; and engineering data such as speed and braking applications. Six automotive safety experts examined 197 ‘valid’ (i.e., conditions met design intent) FCW events and categorized each according to a taxonomy of primary contributing factors. Results indicated that of these valid FCW events, between 55% and 73% could be considered ‘nuisance alerts’ by the driver.

This paper documents the finite element (FE) analysis of a hot stamping process for high strength aluminum sheet. In this process a 7075 blank, heated above its solvus temperature, was simultaneously die quenched and stamped in a room temperature die to form a B-pillar outer reinforcement. Two modeling approaches have been investigated: an isothermal mechanical model and a non-isothermal coupled thermo-mechanical model. The accuracy of each approach was assessed by comparing the predicted strain and thickness distributions to experimental measurements from a formed panel. The coupled thermo-mechanical model provided the most accurate prediction.

Tools are now publicly available that can potentially help a company assess the impact of its water use and risks in relation to their global operations and supply chains. In this paper we describe a comparative analysis of two publicly available tools, specifically the WWF/DEG Water Risk Filter and the WBCSD Global Water Tool that are used to measure the water impact and risk indicators for industrial facilities. By analyzing the risk assessments calculated by these tools for different scenarios that include varying facilities from different industries, one can better gauge the similarities and differences between these water strategy tools. Several scenarios were evaluated using the water tools, and the results are compared and contrasted. As will be shown, the results can vary significantly.

High ductility cast aluminum alloys are seeing more use in vehicles as a greater effort is made to replace components made from heavier steel and iron alloys with lighter weight alloys such as aluminum. High ductility cast aluminum has significant advantages by allowing for complex shape and considerable consolidation of parts in body structures. However, joining can be a challenge because one popular method for aluminum joining, self-piercing riveting (SPR), requires a ductility of greater than 10%, forcing the common high ductility Al alloys to undergo a T6 heat treatment which adds cost and potential distortion issues to Al component. In this study, friction stir spot welding was investigated as a potential joining technique for this material in the as-cast condition. Samples of as-cast Aural-2™ alloy were joined to Aural-2™, 5754, and 6061 alloys, to determine the manufacturing feasibility, weld strength, and fatigue strength using this joining technique.

There have been many articles published in the last decade or so concerning the components of an electronic stability control (ESC) system, as well as numerous statistical studies that attempt to predict the effectiveness of such systems relative to crash involvement. The literature however is free from papers that discuss how engineers might develop such systems in order to achieve desired steering, handling, and stability performance. This task is complicated by the fact that stability control systems are very complex and their designs and what they can do have changed considerably over the years. These systems also differ from manufacturer to manufacturer and from vehicle to vehicle in a given maker of automobiles. In terms of ESC hardware, differences can include all the components as well as the addition or absence of roll rate sensors or active steering gears to name a few.

Design optimization techniques are widely used to drive designs toward a global or a near global optimal solution. However, the achieved optimal solution often appears to be the only choice that an engineer/designer can select as the final design. This is caused by either problem topology or by the nature of optimization algorithms to converge quickly in local/global optimal or both. Problem topology can be unimodal or multimodal with many local and/or global optimal solutions. For multimodal problems, most global algorithms tend to exploit the global optimal solution quickly but at the same time leaving the engineer with only one choice of design. The paper explores the application of genetic algorithms (GA), simulated annealing (SA), and mixed integer problem sequential quadratic programming (MIPSQP) to find multiple local and global solutions using single objective optimization formulation.

A demonstration structure was cast in AM60. The structure, known as the Generic Frame Casting or GFC, was designed specifically to mimic features seen in castings for closure applications. Excised samples were subsequently removed from different areas of the casting and tested under axial loading conditions. Component level tests were also conducted. Comparison of the excised sample results and the component level testing indicated the influence of local properties on the component level deformation. It was shown that varying the casting processing conditions could change the local ductility and yield strength in different areas of casting with the same geometry. Lowering the local ductility decreased the total displacement in a component level test and lowered the amount of energy absorption. Therefore, understanding the processing conditions and their influence on the local properties is important for predicting behavior in a component level test.

The electroluminescence, a process where light is emitted by the recombination of electrically accelerating charges (electrons and holes) on a solid state chip, is the basis of light-emitting-diodes (LEDs) technology. Until the early 90s, LEDs were considered light sources of low efficiency. Nowadays, white high power, high efficiency LED's, based upon fluorophores are extremely promising for both vehicular / automotive and machinery usages. Associate with its high efficient light production, the long life capability of these devices keep improving their performance. In this study, three models of LEDs, from two different manufacturers were used.

Most people still remember the introduction of the IBM PC in 1981 and the first Microsoft Windows operating system in 1985. These were the pioneering technologies that started a revolution in automotive test equipment in the service bay. What was once a purely mechanical garage environment where information was published annually in large paper manuals has evolved into a highly technical computing environment. Today vehicle networks link onboard vehicle control systems with diagnostic systems and updated service information is published daily over the Internet. A lot has changed over the last twenty years, and manufacturers of diagnostic test equipment are learning to deal with the constantly evolving computing platforms and host operating systems. This paper traces the history of automotive diagnostic equipment at Ford Motor Company and shares some of the hard lessons learned from the early systems.

Current road vehicles have tendency of use softer suspension springs to improve ride comfort, but as a moving device with suspension system, vehicles have other parts that can affect attributes for comfort perception, and is necessary the correct definition of which one should be modified to address the comfort issue and avoid impact in attributes for stability. Usually springs are not the main responsible for bad comfort behavior, but shock absorbers and bushings are. A typical passenger car shows a wide possibility of loads carriage and how to set up correctly the suspensions considering its tradeoffs and brand DNA is the main issue.

In South America and other emerging markets sound package development is limited by the cost and weight of its components. Reaching the right balance between cost and a good NVH performance provides an important competitive advantage, therefore any achieved design opportunities can be replicated to other vehicle lines and markets. In this work the main noise transmission paths are verified by evaluating the contribution of sound package components to noise attenuation in two cases, initially from the tire contact patch through vehicle body to a number of positions within the vehicle interior and, next, from the engine compartment, by placing a High Frequency Sound Source (HFSS) at engine faces to the same vehicle interior positions. The main objective is to optimize sound package distribution and to prioritize which areas should have the sound package reinforced in order to improve Tire and Engine noise reduction.

Emerging markets and South America in particular, have quickly become the cornerstone of major automotive companies in recent years. Currently, all major players are located in the region, and this has created an excellent environment for developing market-tailored products. The trend in the design and technology community is one which allows the final customer to improve his own safety and reduce overall power consumption. Throughout the entire automotive industry, the lighting system has always had a very important role to play during its long history. In the past 50 years, vehicular lighting has achieved an important status due to its close relationship by enhancing passenger and vehicle security. In addition, there is still room for improvement in the halogen front lighting system. Particularly, it is of utmost importance to highlight the implementation of NEO (new efficient optics).

Vehicle target setting is an evolving process based on continually changing internal (management, standards) and external (competitive and legal) requirements. In addition to evolving requirements, the process for establishing and documenting targets may not be clear. The objective of this paper is to detail the overall process of target setting, the critical factors to consider, and key definitions for each stage of the process. It will describe the complete process from early competitive benchmarking to final verification testing. Setting targets for a vehicle requires definition and thorough benchmarking of the competition, an understanding of the key attributes used to describe the vehicles' performance, and a clearly defined set of requirements. These requirements will be regulatory, corporate and competitively based and grouped by clearly defined, customer perceived attributes which can be cascaded to specific vehicle systems.

Having, by now, introduced several new vehicles that comply with FMVSS 202a, manufacturers are reporting an increased number of complaints from consumers who find that the head restraint is too close; negatively affecting their posture. It is speculated that one of the reasons that head restraints meeting the new requirement are problematic is that the FMVSS backset measurement is performed at a back angle that is more reclined than the back angle most drivers choose and the back angle at which the seat / vehicle was designed. The objective of this paper is to confirm this hypothesis and elaborate on implications for regulatory compliance in FMVSS 202a.

A detailed investigation of the influence of anisotropic hardening models on drawbead restraining force is presented in this paper. The recently modified Yoshida model is adopted to characterize the anisotropic hardening behavior for steels. A two-dimensional drawbead model is used and the restraining forces corresponding to several different bead penetrations are obtained and compared against experimental results. The comparison of the predicted results for the Modified Yoshida Model with isotropic hardening models indicates that the anisotropic hardening gives lower drawbead restraining forces in general. The impact of hardening models on springback is also presented, and it's demonstrated that the springback amount predicted by the modified Yoshida model is much closer to the experimental data than that predicted by conventional isotropic hardening model.