Search Results

We have studied the formability of continuous strip cast (CC) AA5754 aluminum alloy for automotive applications. Strip casting technology can considerably reduce material cost compared with conventional direct chill (DC) cast aluminum sheets. However, the CC material tends to exhibit much less post-localization deformation and lower fracture strains compared with DC sheets with similar Fe content, although both alloys show similar strains for the onset of localization. Bendability of the CC alloy is also found to be inferior. The inferior behavior (post-necking and bendability) of the CC alloy can be attributed to the higher incidence of stringer-type particle distributions in the alloy. The formability of the AA5754 alloy has also been studied using two dimensional microstructure-based finite element modeling. The microstructures are represented by grains and experimentally measured particle distributions.

The use of sheet magnesium for automobile body applications is limited, in part, due to its low room temperature formability. Elevated temperature forming of magnesium sheet could enable the manufacture of automobile body closure and structural panels to meet vehicle mass targets. The effect of temperature in improving the formability of sheet magnesium has been known since the 1940's; however, automobile applications for sheet magnesium still have been very limited. The present work characterizes the elevated temperature mechanical behavior of commercially available magnesium sheet alloys at temperatures between 300°C and 500°C. The materials are then evaluated using both warm forming and superplastic forming technologies.

A family of low-cost, creep-resistant magnesium alloys has been developed. These alloys, containing aluminum, calcium, and strontium are designated as “ACX” alloys. Developed for engine blocks and transmissions, the “ACX” alloys have at least 40% greater tensile and 25% greater compressive creep resistance than AE42, and corrosion resistance as good as AZ91D (GMPG 9540P/B corrosion test). These alloys are estimated to cost only slightly more than AZ91D and have as good castability. Creep data up to 200°C, tensile properties at room temperature and 175°C, corrosion results and microstructure analysis are presented and discussed. These alloys have the potential to enable the extension of the substantial weight reduction benefits of magnesium to powertrain components.

This paper presents an overview of techniques for measuring friction using bench tests and fired engines. The test methods discussed have been developed to provide efficient, yet realistic, assessments of new component designs, materials, and lubricants for in-cylinder and overall engine applications. A Cameron-Plint Friction and Wear Tester was modified to permit ring-in-piston-groove movement by the test specimen, and used to evaluate a number of cylinder bore coatings for friction and wear performance. In a second study, it was used to evaluate the energy conserving characteristics of several engine lubricant formulations. Results were consistent with engine and vehicle testing, and were correlated with measured fuel economy performance. The Instantaneous IMEP Method for measuring in-cylinder frictional forces was extended to higher engine speeds and to modern, low-friction engine designs.

This paper describes a bench method to evaluate the frictional behavior, under scuffing conditions, of some test coupons of standard materials currently used in making cylinder bores and pistons. The usefulness of this method is in evaluating new materials and coatings that may enable the elimination of iron liners from engine blocks. While investigating the potential application of Plasma Source Ion Implantation (PSII) on engine piston/bore materials, we have systematically studied the scuffing related friction behavior of aluminum 390 alloy and cast iron. A pin-on-disk tribometer is used under dry sliding conditions. Testing parameters for simulating cold scuff in bench tests have been specified. This proposed test method offers a screening tool desirable for the development of PSII technology and may also be useful for the design of other new surface modification techniques.

This paper examines the potential use of diamond-like carbon (DLC) on aluminum alloy pistons of internal combustion engines. Our approach is to apply a DLC coating on the piston running against an aluminum-390 bore thus eliminating the iron liners in a standard piston/bore system. Experimental data, using a pin-on-disk tribometer under unlubricated test conditions, indicate that the performance of the DLC coating against aluminum 390 exhibits superior friction resistance compared to aluminum-390 against cast iron; the latter material couple representing the materials currently being used in production for the piston/bore application. Moreover, by thermally cycling the DLC coatings we show that improved friction and wear properties can he maintained to temperatures as high as 400°C.

ACuZinc™ 5, a GM-patented, high-performance ternary zinc-copper-aluminum alloy which is suitable for manufacturing net shape die castings, plays a vital role in the success of new automotive parts and systems. The new parts were designed to meet the auto industry's higher load and safety specifications. The superior mechanical properties of ACuZinc™ make it suitable for structural applications where commercial zinc die casting alloys have been found to be inadequate. From a business viewpoint, ACuZinc™ can help in penetrating new markets by competing for cast iron, powder metal and brass applications. ACuZinc is a registered GM trademark.