Search Results

The proposed Euro-7 regulations are expected to build on the significant emissions reductions that have already been achieved using advanced Euro VI compliant after treatment systems (ATS). The introduction of in-service conformity (ISC) requirements during Euro VI paved the way for enabling compliance during real-world driving conditions. The diverse range of applications and resulting operating conditions greatly impact ATS design and the ability of the diesel particulate filter (DPF) to maintain performance under the most challenging boundary conditions including cold starts, partial/complete regenerations, and high passive soot burn operation. The current study attempts to map the particle number (PN) filtration performance of different DPF technologies under a variety of in-use cycles developed based on field-data from heavy duty Class-8 / N3 vehicles.

With more stringent CO2 emission regulation in the world, Plug-in Hybrid Electric Vehicle (PHEV, also known as off-vehicle charging hybrid electric vehicle, OVC-HEV) plays a more important role in the current modern market, such as in China. At the same time, Real Driving Emission (RDE) was introduced in both Euro 6d and China 6b regulation, which covers more factors in the real driving practice including altitude, environment temperature, fuel quality, driving behaviors, and so on, which could potentially impact the pollutant emissions. Besides above mentioned, for PHEV, the state of charge (SOC) of the battery is also considered as one important factor, which could impact the engine load and emissions.

Gasoline particulate filters (GPF) have become a standard aftertreatment component in Europe, China, and since recently, India, where particulate emissions are based on a particle number (PN) standard. The anticipated evolution of regulations in these regions towards future EU7, CN7, and BS7 standards further enhances the needs with respect to the filtration capabilities of the GPFs used. Emission performance has to be met over a broader range in particle size, counting particles down to 10nm, and over a broader range of boundary conditions. The requirements with respect to pressure drop, aiming for as low as possible, and durability remain similar or are also enhanced further. To address these future needs new filter technologies have been developed. New technologies for uncatalyzed GPF applications have been introduced in our previous publications.

The gasoline particulate filter (GPF) represents a practical solution for particulate emissions control in light-duty gasoline-fueled vehicles. It is also seen as an essential technology in North America to meet the upcoming US EPA tailpipe emission regulation, as proposed in the “Multi-pollutant Rule for Model Year 2027”. The goal of this study was to introduce advanced, uncoated GPF products and measure their particulate mass (PM) reduction performance within the existing US EPA FTP vehicle testing procedures, as detailed in Code of Federal Regulations (CFR) part 1066. Various state-of-the-art GPF products were characterized for their microstructure properties with lab-bench checks for pressure drop and filtration efficiency, then pre-conditioned with an EPA-recommended 1500 mile on-road break-in, and finally were tested on an AWD vehicle chassis-dyno emissions test cell at both 25°C and -7°C ambient conditions.

Powertrain development requires an efficient development process with no rework and model-based development (MBD). In addition, to performance design that achieves low CO2 emissions is also required. Furthermore, it also demands fuel economy performance considering real-world usage conditions, and in North America, the EPA (U.S. Environmental Protection Agency) 5-cycle, which evaluates performance in a combination of various environments, is applied. This evaluation mode necessitates predicting performance while considering engine heat flow. Particularly, simulation technology that considers behavior based on engine temperature for Hybrid Electric Vehicle (HEV) is necessary. Additionally, in the development trend of vehicle aerodynamic improvement, variable devices like Active Grille Shutter (AGS) are utilized to contribute to reducing CO2 emissions.

The ever-tightening regulation norms across the world emphasize the magnitude of the air pollution problem. The decision to leapfrog from BS4 to BS6 – with further reduction in emission limits -showed India’s commitment to clean up its atmosphere. The overall cycle emissions were reduced significantly to meet BS6 targets [1]. However, the introduction of RDE norms in BS6.2 [1] demanded further reduction in emissions under real time operating conditions – start-stop, hard acceleration, idling, cold start – which was possible only through strategies that demanded a cost effective yet robust solutions. The first few seconds of the engine operation after start contribute significantly to the cycle gaseous emissions. This is because the thermal inertia of the catalytic converter restricts the rate at which temperature of the catalyst increases and achieves the desired “light-off” temperature.

In this paper, a newly developed Active Noise Control (ANC) system is introduced, that effectively reduces road noise, which becomes a major issue with electrified vehicles, and that enhances vehicle interior sound levels matching seamless acceleration by electric drive. Conventionally, reducing road noise using ANC requires numerous sensors and speakers, as well as a processor with high computing power. Therefore, the increase in system cost and the complexity of the system are obstacles to its spread. To overcome these issues, this system is developed based on four concepts. The first is a modular system configuration with unified interface to apply to various vehicle types and grades. The second is the integration and optimal placement of noise source reference sensors to achieve both reduction in number of parts and noise reduction performance.

Honda has developed a new hybrid system targeting the C and D segments that aims for the latest environmental performance, high fuel economy, and enhanced acceleration feeling in driving. The new engine to be applied to this new hybrid system has been developed with the goal of expanding the high thermal efficiency range, realizing the latest environmental performance, and high quietness. The new engine has adopted the Atkinson cycle and cooled exhaust gas recirculation (EGR) carried over from the previous model [1], and employed an in-cylinder direct fuel injection system with fuel injection pressure of 35 MPa. The combustion chamber and ports have been newly designed to match the fuel system changes. By realizing high-speed combustion, the engine realized a high compression ratio with the mechanical compression ratio of 13.9.

As the official proposal for emission regulation Euro 7 has been released by European Commission, PN above 10nm is taken into consideration for the ultrafine particulate emissions control. The challenges of GPF filtration efficiency emerge for the light-duty manufactures to meet the future emission standards. In the present study, a China 6 compliant vehicle was tested to reveal its performance over the China 6 standards and potential to meet the upcoming Euro 7. Three GPF product types (Gen 1, Gen 2, and concept Gen 3) were mounted to the tested vehicle. WLTC tests were conducted on chassis dynamometer in laboratory as well as a self-designed aggressive cycle (“Base Cycle”) tests. To explore the GPFs performance for PN emissions above 10nm against the proposed limit 6.0E11 #/km, PN emission above 10nm were measured in our laboratory tests for both engine out and tailpipe as well as the PN emission above 23nm.

As in the past several years, we provide here an overview of recent major regulatory and technological changes for reducing emissions from the transport and off-road sector. In the past, this review was focused mostly on improvement in engine efficiency and tailpipe emissions of criteria pollutants. However, starting last year [1] we have increased the scope to broadly address the increased focus on greenhouse gas emissions and the emergence of various non-conventional fuel pathways to achieve the various decarbonization goals. There are two broad themes that are emerging, and which we describe here. Firstly, that we are approaching the implementation of the last of the major regulations on criteria pollutant emissions from cars and trucks, led by Europe, through Euro 7 standards and US, through multi-pollutant standards for light- and heavy-duty vehicles.

5 belt wind tunnels are the most common facility to conduct the experimental aerodynamics development for production cars. Among aerodynamic properties, usually drag is the most important development target, but lift force and its front/rear balance is also important for vehicle dynamics. Related to the lift measurement, it is known that the “pad correction”, the correction in the lift measurement values for the undesirable aerodynamic force acting on wheel belt surface around the tire contact patch, must be accounted. Due to the pad correction measurement difficulties, it is common to simply subtract a fixed amount of lift values from measured lift force. However, this method is obviously not perfect as the pad corrections are different for differing vehicle body shapes, aerodynamic configurations, tire sizes and shapes.

RDE test has been introduced to the light-duty vehicle certification process in both China 6 and Euro 6d standards. The RDE test shall be performed on-road with PEMS, which is developed to complement the current laboratory certification of vehicles and ensure cars to deliver low emissions under more realistic on-road driving conditions. Particulate matter has been highly perceived as a significant contributor to human health risks and thus strictly regulated globally. For the RDE evaluation, the MAW method used by the China 6 standard is usually found less stringent than the RMA method used by the Euro 6d standard. In the present study, both of the MAW and RMA methods were applied to different driving cycles and operating conditions, which met the general RDE test requirements, yet resulted in different evaluated PN results.

This review covers advances in regulations and technologies in the past year in the field of vehicular emissions. We cover major developments towards reducing criteria pollutants and greenhouse gas emissions from both light- and heavy-duty vehicles and off-road machinery. To suggest that the transportation is transforming rapidly is an understatement, and many changes have happened already since our review last year [1]. Notably, the US and Europe revised the CO2 standards for light-duty vehicles and electrification mandates were introduced in various regions of the world. These have accelerated plans to introduce electrified powertrains, which include hybrids and pure electric vehicles. However, a full transformation to electric vehicles and the required grid decarbonization will take time, and policy makers are accordingly also tightening criteria pollutant standards for internal combustion engines.

India BS6 Stage2 (2023) regulations demand all gasoline direct injection (GDI) vehicles to meet particulate number emissions (PN) below 6x10+11# per km. Gasoline particulate filters (GPF) are a proven technology and enable high PN filtration efficiencies throughout the entire vehicle lifetime. One challenge for GPF applications could be the changing emission performance characteristics as a function of mileage due to collected ash and/or soot deposits with implications on back pressure losses. The main objective of this technical contribution is to study the above-mentioned challenges while applying Indian driving conditions and typical Indian climate and other ambient conditions. The substrate technology selected for this study is a high porosity GPF designed to enable the integration of a three-way functionality into the GPF, commonly described as catalyzed GPF (cGPF).

With the introduction of EU6d and CN6 all vehicles with gasoline direct injection and many with port fuel injection engine will be equipped with a gasoline particulate filter (GPF). A range of first generation filter technologies has been introduced successfully, helping to significantly reduce the tailpipe particulate number emissions. The continued focus on particulate emissions and the increasing understanding of their impact on human health, combined with the advanced emission regulations under RDE conditions results in the desire for filters with even higher filtration efficiency, especially in the totally fresh state. At the same time, to balance with the requirements on power and CO2, limitations exist with respect to the tolerable pressure drop of filters. In this paper we will report on a new generation of gasoline particulate filters for uncatalyzed applications.

The ceramic wall-flow filter has now been globally commercialized for aftertreatment systems in light-duty gasoline engine powered vehicles. This technology, known as the gasoline particulate filter (GPF), represents a durable solution for particulate emissions control. The goal of this study was to track the evolution of tailpipe particulate and gaseous emissions of a 4-cylinder gasoline turbocharged direct injected (GTDI) 2018 North American (NA) mild-hybrid light-duty SUV, from a fresh state to the 4,000-mile, EPA certification mileage level. For this purpose, a production TWC + GPF aftertreatment system designed for a China 6b-compliant variant of this test vehicle was retrofitted in place of the North American Tier 3 Bin 85 TWC-only system. Chassis dyno emissions testing was performed at predetermined mileage points with real-world, on-road driving conducted for the necessary mileage accumulation.

As the China 6 light duty vehicle emission regulation is being implemented, PN becomes a challenge for vehicle type-approval emission tests. WLTC has replaced NEDC as the Type-I test cycle on the chassis dynamometer with more dynamic driving events. In addition, on-road RDE test is a challenge to calibrate the engine to meet tailpipe PN emissions because of the nature of the on-road conditions, i.e. varying ambient temperature, driving dynamics, altitude, etc. In response to China 6 requirements, GPF technology has been introduced. In this study, we pulled four China 6 compliant gasoline vehicles for the PN emission survey. The selected vehicles covered typical engine technologies including GDI/MPI with natural aspiration/turbo charger, representing the state of the art of the local engine capability. On one hand, it helps to build insight into the status of China 6 engine emission control technology through WLTC and RTS95 tests.

For more than two decades [1,2], Corning has served the community with an annual review of global regulatory and technological advances pertaining to emissions from internal combustion engine (ICE) driven vehicles and machinery. We continue with a review for the year 2020, which will be remembered by COVID and the significant negative impact it had on the industry. However, it also provided a glimpse of the possible improvement in air quality with reduced anthropogenic emissions. It was a year marked by goals set for climate change mitigation via reduced fossil fuel use by the transportation sector. Governments stepped up plans to accelerate the adoption of zero tailpipe emitting vehicles. However, any transformation of the transportation sector is not going to happen overnight due to the scale of the infrastructure and technology challenges. A case in point is China, which announced a technology roadmap which envisions half of the vehicles to be hybrids in 2035.

Accelerated ash loading studies provide a cost-effective means of investigating the long-term impacts of ash accumulation in diesel particulate filters (DPFs). Despite a variety of methods adopted in previous studies for accelerated ash loading, evaluation of their impact on DPF behavior has been limited primarily to pressure drop response (with & without soot), and characterization of properties of the resulting ash deposits for comparison with samples from field testing. In the current study, the potential to use ash recovered from field DPFs to perform accelerated ash loading studies is explored. Additionally, anhydrous gypsum as a surrogate for diesel ash was investigated. Benefits of using gypsum include low cost and easy access, safety during handling and testing, and consistency from test to test. Narrow control of particle sizing and composition can help compare performance over a wide range of filter sizes and applications.

According to some papers, the label fuel economy and the actual fuel economy experienced by the customers may exhibit a gap. One of the reasons may stem from the aerodynamic drag variations due to the natural wind. The fuel consumption is measured through bench test under several driving modes by using the road load as input condition. The road load is measured through the coast down test under less wind ambient conditions as determined by each regulation. The present paper aims to analyze the natural wind conditions encountered by the vehicle on public roads and to operate a comparison between the fuel consumptions and the driving energy. In this paper, the driving energy is calculated by the aerodynamic drag from the natural wind specifications and driving conditions. This driving energy and the fuel consumptions show good correlation. The fuel consumption is obtained from the vehicle Engine control unit(ECU) data.